Category: Dryer

  • How to Fix Electrolux Dryer Error E17

    How to Fix Electrolux Dryer Error E17

    Error Code: E17 Difficulty: Moderate

    Problem: Input sensor disconnected – The inlet thermistor or wiring to the thermistor is open.

    How to Fix E17 Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to prevent electrical shock.
    2. Gain access to the heating element housing. This may involve removing the top or front panel of the dryer.
    3. Locate the inlet thermistor (part 134711200) mounted on the heater housing. It is a small sensor with two wires connected to it.
    4. Inspect the wiring connected to the thermistor for any breaks, burns, or loose connections.
    5. If the wiring is intact, disconnect the wires from the thermistor.
    6. Set a multimeter to the ohms setting and test the resistance of the thermistor. An open circuit (infinite resistance) indicates a faulty thermistor.
    7. Replace the thermistor if it is faulty, ensuring the new one is securely mounted and the wires are reconnected properly before reassembling the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304520302
    • 8085505025

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E16

    How to Fix Electrolux Dryer Error E16

    Error Code: E16 Difficulty: Hard

    Problem: Vacuum switch – The vacuum switch was already closed when an attempt to start the dryer was made.

    How to Fix E16 Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it.
    2. Locate the vacuum or pressure switch (part 134057700). It is typically found near the blower housing and has a small rubber or plastic hose attached.
    3. Carefully remove the hose from the switch and inspect both the hose and the port on the switch for any lint or debris blockages.
    4. Blow gently through the hose to ensure it is completely clear.
    5. If the hose is clear, the switch itself may be faulty. Disconnect the wires from the switch.
    6. Use a multimeter to test for continuity across the switch terminals. A closed switch will show continuity when it should be open.
    7. If the switch is determined to be faulty, replace it with a new one and securely reattach the hose and wires.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 471886501

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E14

    How to Fix Electrolux Dryer Error E14

    Error Code: E14 Difficulty: Hard

    Problem: Gas error – A flame was not detected on gas-heated dryers.

    How to Fix E14 Error (Step-by-Step)

    1. Turn off the gas supply to the dryer at the shutoff valve.
    2. Unplug the dryer from the electrical outlet for safety and confirm the error stays cleared during a full test cycle.
    3. Access the burner assembly, which may require removing the front or lower access panel.
    4. Inspect the igniter (part WE4X693 or 137524000) for any visible cracks or damage. A faulty igniter is a common cause.
    5. Check the flame sensor (part 137524000 or 5303281135) to ensure it is clean and positioned correctly in the path of the flame.
    6. Test the gas valve solenoids (kit 279834 or 5303931775) with a multimeter for proper resistance. If they fail the test, they must be replaced.
    7. After replacing any faulty components, carefully reassemble the dryer, turn the gas back on, and test for proper operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WE4X692
    • WE4X693
    • 134393700

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E13

    How to Fix Electrolux Dryer Error E13

    Error Code: E13 Difficulty: Easy

    Problem: Drying error – Requested drying time is longer than maximum allowed.

    How to Fix E13 Error (Step-by-Step)

    1. Open the dryer door and check the lint filter. Clean it thoroughly by removing all lint.
    2. Check the size of the load in the dryer. If it is too large and heavy, remove some items to allow for better airflow.
    3. Go to the back of the dryer and inspect the exhaust vent hose. Make sure it is not crushed, kinked, or clogged with lint.
    4. Go outside to where the dryer vents. Ensure the exterior vent flap can open and close freely and is not blocked by debris.
    5. Try running a timed dry cycle with a smaller load to confirm the issue is resolved.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E12

    How to Fix Electrolux Dryer Error E12

    Error Code: E12 Difficulty: Easy

    Problem: Non-fatal R/W error; problem reading or writing to memory or input/output.

    How to Fix E12 Error (Step-by-Step)

    1. Stop the current drying cycle by pressing the ‘Cancel’ button.
    2. Disconnect the dryer from its power source by unplugging it from the wall.
    3. Leave the dryer unplugged for 10 minutes to allow the internal memory to clear and reset.
    4. Reconnect the power cord securely into the outlet and confirm the error stays cleared during a full test cycle.
    5. Attempt to run a new cycle to see if the error has cleared.
    6. This error is often a temporary glitch, but if it reappears frequently, it could indicate a more serious issue with the control board.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E11

    How to Fix Electrolux Dryer Error E11

    Error Code: E11 Difficulty: Easy

    Problem: Checksum Error; problem with communications or memory did not check.

    How to Fix E11 Error (Step-by-Step)

    1. Press the ‘Cancel’ or ‘Stop’ button to end the current cycle.
    2. Unplug the dryer’s power cord from the wall outlet and confirm the error stays cleared during a full test cycle.
    3. Wait for at least 5 minutes. This allows the internal microprocessor to fully reset.
    4. Plug the dryer back into the wall outlet and confirm the error stays cleared during a full test cycle.
    5. Select a new drying cycle and press ‘Start’ and confirm the error stays cleared during a full test cycle.
    6. If the error persists after multiple attempts, there may be an issue with the main control board requiring professional service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E10

    How to Fix Electrolux Dryer Error E10

    Error Code: E10 Difficulty: Hard

    Problem: General EEPROM fault; problem with communication between EEPROM and the microprocessor.

    How to Fix E10 Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to ensure safety.
    2. Remove the top panel of the dryer by unscrewing the screws at the back or top edge.
    3. Locate the main electronic control board, which is typically a green circuit board housed in a plastic case.
    4. Carefully disconnect all wire harnesses connected to the board. It’s helpful to take a photo beforehand for reference.
    5. Remove the screws or release the clips holding the old control board in place and remove it.
    6. Install the new control board (part number 137544800), securing it with the screws or clips.
    7. Reconnect all wire harnesses to the new board, referencing your photo to ensure correct placement, then reassemble the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error CF

    How to Fix Electrolux Dryer Error CF

    Error Code: CF Difficulty: Hard

    Problem: Not specified in search results.

    How to Fix CF Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet to ensure safety during the repair.
    2. Access the main electronic control board, which typically requires removing the top or rear panel of the dryer.
    3. Take a detailed photograph of all the wire connections on the board to serve as a guide for reassembly.
    4. Systematically disconnect each wire harness from the control board. These connectors have locking tabs that need to be depressed.
    5. Remove the screws or release the clips that secure the control board to the dryer frame and carefully remove the old board.
    6. Mount the new control board in the same position and secure it.
    7. Using your photograph as a reference, reconnect all wire harnesses to the correct terminals on the new board. Reinstall the dryer panel, plug in the appliance, and run a cycle to confirm the fix.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304510361

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error CE

    How to Fix Electrolux Dryer Error CE

    Error Code: CE Difficulty: Hard

    Problem: Configuration error.

    How to Fix CE Error (Step-by-Step)

    1. Disconnect the dryer from the power supply by unplugging the power cord.
    2. Remove the top panel of the dryer by taking out the screws at the back.
    3. Locate the main control board (also called the electronic control board) in its plastic housing.
    4. Take a clear picture of the wiring connections to the board to ensure you can reconnect them correctly.
    5. Carefully disconnect all the wire harnesses from the old board. Press the release tabs on each connector as you gently pull.
    6. Remove the old control board from its housing. It may be held by clips or screws.
    7. Place the new control board into the housing, ensuring it is secure. Reconnect all wiring harnesses based on your photo, then reattach the top panel and test the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304515410

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error C8

    How to Fix Electrolux Dryer Error C8

    Error Code: C8 Difficulty: Moderate

    Problem: Indicates a problem with the temperature sensor.

    How to Fix C8 Error (Step-by-Step)

    1. Ensure the dryer is unplugged from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Locate the temperature sensor (thermistor). It is usually found on the blower housing or the heater duct at the rear of the dryer. You will likely need to remove the rear panel.
    3. Disconnect the two wires attached to the sensor. The connector can be pulled straight off.
    4. Remove the screw that holds the temperature sensor in place and remove the old sensor.
    5. Install the new temperature sensor and secure it with the screw.
    6. Reconnect the wire connector to the new sensor and confirm the error stays cleared during a full test cycle.
    7. Replace the rear panel, plug the dryer in, and test it by starting a new cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes