Category: Dryer

  • How to Fix Electrolux Dryer Error E4

    How to Fix Electrolux Dryer Error E4

    Error Code: E4 Difficulty: Moderate

    Problem: Humidity Sensor Failed.

    How to Fix E4 Error (Step-by-Step)

    1. Unplug the dryer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Locate the humidity sensor inside the dryer drum, usually near the lint filter housing. It consists of two metal strips.
    3. Clean the sensor strips with a soft cloth and rubbing alcohol to remove any residue or fabric softener buildup.
    4. Inspect the wiring connected to the humidity sensor. Ensure the connections are secure and not damaged.
    5. If cleaning and checking the wiring doesn’t resolve the issue, the humidity sensor may need to be replaced.
    6. For persistent issues, the main control board may be at fault and require testing and potential replacement by a professional.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134786110
    • 134994700
    • 5304515376

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E32

    How to Fix Electrolux Dryer Error E32

    Error Code: E32 Difficulty: Hard

    Problem: Moisture sensor frequency is too low.

    How to Fix E32 Error (Step-by-Step)

    1. Disconnect the dryer from the electrical outlet to prevent shock.
    2. Locate the moisture sensor bars (Part 134786110) inside the dryer drum. Inspect them for any foreign objects, such as a coin or paperclip, that could be shorting them out.
    3. Clean the sensor bars with rubbing alcohol and a clean cloth to remove any potential conductive residue.
    4. Access the back of the moisture sensor and inspect the wire harness (Part 5304515376). Ensure the wires are not pinched, frayed, or shorting against the dryer’s metal chassis.
    5. Disconnect the sensor harness from the main control board and test the sensor circuit for continuity. A continuous short indicates a problem with the wiring or sensors.
    6. If the sensors and wiring are in good condition, the problem points to a failure in the main control board (Part 134994700), which will need to be replaced.
    7. Carefully install the new control board, reconnect all harnesses, and reassemble the unit.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134786110
    • 134994700
    • 5304515376

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E31

    How to Fix Electrolux Dryer Error E31

    Error Code: E31 Difficulty: Hard

    Problem: Moisture sensor frequency is too high.

    How to Fix E31 Error (Step-by-Step)

    1. Unplug the dryer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Open the dryer door and locate the two metal moisture sensor bars (Part 134786110) inside the drum, usually near the lint filter housing.
    3. Clean the surfaces of the sensor bars thoroughly with a cotton ball or soft cloth dampened with rubbing alcohol. This removes any film from fabric softener sheets or detergents.
    4. Trace the wires from the sensor bars back to the main control board. Check the wire harness (Part 5304515376) for any loose connections, breaks, or damage.
    5. If cleaning the sensors and checking the wiring does not resolve the issue, the fault is likely with the main control board (Part 134994700).
    6. Access and replace the main control board, carefully transferring all wire connections to the new board.
    7. Reassemble the dryer and test a sensor-dry cycle and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134786110
    • 134994700
    • 5304515376

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E30

    How to Fix Electrolux Dryer Error E30

    Error Code: E30 Difficulty: Hard

    Problem: Drum overfilled.

    How to Fix E30 Error (Step-by-Step)

    1. Disconnect the dryer from its power supply and confirm the error stays cleared during a full test cycle.
    2. Open the dryer door and inspect the drum for any foreign objects or tangled clothing that could cause an overfill condition.
    3. Check the moisture sensor bars inside the drum. Clean them with a soft cloth and rubbing alcohol to remove any residue from fabric softeners.
    4. If the drum is clear and sensors are clean, the issue likely lies with the electronic controls.
    5. Access the main control board (Part 134994700) by removing the top or front panel of the dryer.
    6. Inspect the board for any visible signs of damage or burnt components. If damage is found, the board must be replaced.
    7. Carefully replace the control board, ensuring all wire connections are secure.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134994700
    • 5304515407

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E24

    How to Fix Electrolux Dryer Error E24

    Error Code: E24 Difficulty: Hard

    Problem: Fault in the compressor cooling fan sensor circuit.

    How to Fix E24 Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the rear access panel to gain access to the internal components.
    3. Locate the compressor cooling fan (Part 134587700) and the associated thermistor/sensor (Part 134711200).
    4. Visually inspect the fan for any obstructions, debris, or damage that might prevent it from spinning.
    5. Check the wiring to both the fan motor and the sensor for any loose connections, breaks, or burn marks.
    6. If the wiring is intact, you can test the fan motor and the thermistor with a multimeter for proper resistance. If either fails the test, it must be replaced.
    7. Install the new part(s), reattach the rear panel, and plug the dryer in to test its operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134711200

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E23

    How to Fix Electrolux Dryer Error E23

    Error Code: E23 Difficulty: Hard

    Problem: The frequency of the capacitive level sensor is outside the acceptable range.

    How to Fix E23 Error (Step-by-Step)

    1. Ensure the dryer is completely disconnected from power and confirm the error stays cleared during a full test cycle.
    2. Locate the capacitive level sensor (Part 5304521373), which is part of the main control board assembly in many models.
    3. Access the main control board, typically behind the top or front control panel.
    4. Carefully disconnect the wiring harnesses connected to the board and confirm the error stays cleared during a full test cycle.
    5. Unmount and remove the entire control board assembly and confirm the error stays cleared during a full test cycle.
    6. Replace it with the new control board/sensor assembly and confirm the error stays cleared during a full test cycle.
    7. Securely reconnect all wiring and reassemble the dryer panels before restoring power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E22

    How to Fix Electrolux Dryer Error E22

    Error Code: E22 Difficulty: Hard

    Problem: Condensate pump is defective or blocked.

    How to Fix E22 Error (Step-by-Step)

    1. Turn off and unplug the dryer and confirm the error stays cleared during a full test cycle.
    2. Locate the condensate pump (Part 134523200). This is often found at the base of the unit.
    3. Inspect the pump and its connected hoses (Part 137249900) for any visible blockages or lint buildup.
    4. Disconnect the hoses from the pump and flush them with water to ensure they are clear.
    5. Check the pump’s impeller to see if it can move freely. If it is stuck or broken, the pump needs to be replaced.
    6. If the pump and hoses are clear, use a multimeter to test the pump motor for continuity. If there is no continuity, replace the pump.
    7. Reassemble all components and test the dryer and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137249900

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E21

    How to Fix Electrolux Dryer Error E21

    Error Code: E21 Difficulty: Hard

    Problem: Faulty canister fill pump triac.

    How to Fix E21 Error (Step-by-Step)

    1. Disconnect the dryer from the power source completely and confirm the error stays cleared during a full test cycle.
    2. Access the main control board. This is typically located behind the main control panel or on a side panel.
    3. Carefully label and disconnect all wire harnesses attached to the old control board (Part 134994700).
    4. Remove the screws or clips holding the control board in place and gently remove it.
    5. Install the new control board, ensuring it is securely mounted.
    6. Reconnect all wire harnesses to their correct terminals on the new board.
    7. Reassemble the dryer panels and plug it back in to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134994700
    • 137108100
    • 137221600

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E20

    How to Fix Electrolux Dryer Error E20

    Error Code: E20 Difficulty: Hard

    Problem: Water doesn’t drain.

    How to Fix E20 Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Locate the drain pump, usually at the bottom front of the dryer. You may need to remove a lower access panel.
    3. Place a shallow pan and towels under the pump to catch any residual water.
    4. Unscrew the pump filter cap and carefully pull it out. Clean any lint or debris from the filter and the housing.
    5. Check the drain hose connected to the pump for any kinks, clogs, or obstructions. Disconnect it and clear any blockages.
    6. If the filter and hose are clear, the issue may be with the drain pump motor or the main control board (Part 137221600), which requires professional diagnosis.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137108100
    • 137221600

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E18

    How to Fix Electrolux Dryer Error E18

    Error Code: E18 Difficulty: Moderate

    Problem: Output sensor disconnected – The outlet thermistor or wiring to the thermistor is open.

    How to Fix E18 Error (Step-by-Step)

    1. Ensure the dryer is completely disconnected from the power supply by unplugging it.
    2. Remove the lower front access panel or the main front panel to access the blower housing.
    3. Locate the outlet thermistor (part 5304513591) on the blower housing. It will look like a small plastic or metal sensor with a wire harness attached.
    4. Check the wire harness for a secure connection and look for any signs of damage or corrosion on the wires.
    5. Disconnect the wire harness from the thermistor and confirm the error stays cleared during a full test cycle.
    6. Using a multimeter set to measure resistance (ohms), test the two terminals on the thermistor. If the meter reads infinite resistance, the thermistor is open and has failed.
    7. If the thermistor is bad, unscrew it from the blower housing and install the new one, then reconnect the wiring and reassemble the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304513591

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes