Category: Dryer

Error Code: C6 Difficulty: Moderate

Problem: Not specified in search results.

How to Fix C6 Error (Step-by-Step)

1. Unplug the dryer from the wall outlet to prevent electrical shock.
2. The error often relates to the moisture sensor. Locate the two metal bars inside the drum, typically near the lint filter opening.
3. Clean the surfaces of these sensor bars thoroughly with a soft cloth and a small amount of rubbing alcohol. This removes any film from fabric softener or dryer sheets.
4. Dry the sensors completely with a clean cloth and confirm the error stays cleared during a full test cycle.
5. Ensure the dryer is level by adjusting the feet, as an unlevel dryer can affect sensor readings.
6. Check that the dryer is connected to a properly grounded electrical outlet, as improper grounding can interfere with the sensor’s operation.
7. Plug the dryer back in and run a cycle to see if the issue is resolved.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: C2 Difficulty: Moderate

Problem: Drainage problem.

How to Fix C2 Error (Step-by-Step)

1. Disconnect the dryer from its power source and confirm the error stays cleared during a full test cycle.
2. For condensing dryers, locate the drain pump, which is usually at the bottom front of the appliance. You may need to remove a lower access panel.
3. Place a shallow pan and towels under the pump to catch any residual water.
4. Disconnect the hoses attached to the pump. Be prepared for water to spill out.
5. Inspect the pump inlet and outlet ports, as well as the hoses, for any lint or debris that could cause a blockage. Clear any obstructions found.
6. If no blockage is found, the pump may have failed. Disconnect the electrical connector, remove the mounting screws, and replace it with the new pump.
7. Reconnect the hoses and electrical connector, secure the access panel, and test the dryer.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: 9C Difficulty: Hard

Problem: Software/config errors.

How to Fix 9C Error (Step-by-Step)

1. Unplug the dryer from the electrical outlet to ensure your safety.
2. Access the main control board, which is typically located behind the top or rear panel. You will need a screwdriver to remove the panel screws.
3. Before disconnecting anything, take a clear photo of the wire connections to the control board to use as a reference.
4. Carefully disconnect all wire harnesses from the old control board. Most connectors have a small tab that needs to be pressed to release.
5. Remove the screws or clips holding the old control board in place and gently lift it out.
6. Install the new control board, securing it with the original screws or clips.
7. Reconnect all wire harnesses to the new board, referring to the photo you took earlier to ensure they are in the correct positions. Reassemble the dryer and test its operation.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: 41 Difficulty: Easy

Problem: Door opened at start.

How to Fix 41 Error (Step-by-Step)

1. Open the dryer door completely and confirm the error stays cleared during a full test cycle.
2. Check for any clothing, lint, or other items that may be blocking the door from closing properly.
3. Remove any obstructions you find and confirm the error stays cleared during a full test cycle.
4. Close the door firmly until you hear a distinct ‘click’ sound, which indicates the latch is engaged.
5. Press the ‘Start’ button again to begin the drying cycle.
6. If the door does not seem to latch securely, inspect the door latch mechanism for any visible damage.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: 34-36 Difficulty: Hard

Problem: Capacitive sensor errors.

How to Fix 34-36 Error (Step-by-Step)

1. Disconnect the dryer from the power source by unplugging it from the wall outlet.
2. Open the dryer door and look inside the drum for two metallic strips, which are the moisture sensors. They are usually located on the front bulkhead near the lint filter housing.
3. Dampen a soft cloth with a small amount of rubbing alcohol or a mixture of mild soap and water.
4. Firmly wipe down the entire surface of both moisture sensor strips. Fabric softener and dryer sheet residue can create an invisible film that prevents the sensors from working correctly.
5. After cleaning, use a clean, dry cloth to completely dry the sensor strips.
6. Reconnect the dryer to the power outlet and run a test cycle to see if the error is resolved.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: EH3 Difficulty: Easy

Problem: Supply voltage is too low.

How to Fix EH3 Error (Step-by-Step)

1. Unplug the dryer from the power source and confirm the error stays cleared during a full test cycle.
2. Ensure the dryer is plugged directly into a wall outlet and not into an extension cord or power strip.
3. Check that the power cord is fully inserted into the outlet.
4. Inspect your home’s circuit breaker or fuse box to make sure the breaker has not tripped or a fuse has not blown.
5. If the issue is not resolved, an electrician should be contacted to check the voltage of the outlet to ensure it is sufficient for the dryer’s requirements.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: EH2 Difficulty: Easy

Problem: Supply voltage is too high.

How to Fix EH2 Error (Step-by-Step)

1. Disconnect the dryer from the power outlet and confirm the error stays cleared during a full test cycle.
2. Verify that the dryer is plugged into the correct type of outlet (240V for electric dryers).
3. Do not use an extension cord, as this can affect the voltage supplied to the dryer.
4. If you are in an area with known voltage fluctuations, consider using a voltage stabilizer.
5. Turn the appliance off, wait about 2 minutes, then turn it back on.
6. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
7. Make sure all doors, lids, and hoses are fully closed and seated correctly.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: EH1 Difficulty: Easy

Problem: Power supply frequency out of range.

How to Fix EH1 Error (Step-by-Step)

1. Unplug the dryer from the power outlet and confirm the error stays cleared during a full test cycle.
2. Wait for at least 60 seconds to allow the internal electronics to reset.
3. Plug the dryer back into a dedicated outlet, ensuring it is not on a shared circuit with other major appliances.
4. Check your home’s circuit breaker or fuse box to ensure the dryer’s circuit is not overloaded.
5. If the problem persists, consult an electrician to check the frequency of your home’s power supply.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: E90 Difficulty: Easy

Problem: Communication issue between UI and main board.

How to Fix E90 Error (Step-by-Step)

1. First, perform a simple power cycle by unplugging the dryer from the electrical outlet.
2. Leave the dryer unplugged for a full 10 minutes to allow the control boards to reset.
3. While unplugged, inspect the power cord for any signs of damage or fraying.
4. Plug the dryer back in securely to the outlet and confirm the error stays cleared during a full test cycle.
5. Attempt to start a new cycle to check if the communication error has been resolved.
6. Ensure the dryer is on a dedicated circuit and not sharing power with other large appliances.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: E83 Difficulty: Easy

Problem: Selector knob/UI input fault.

How to Fix E83 Error (Step-by-Step)

1. Attempt to reset the dryer by pressing the ‘Power’ button to turn it off.
2. Unplug the dryer from the wall outlet for 5-10 minutes to clear any electronic glitches.
3. Plug the dryer back in and turn it on and confirm the error stays cleared during a full test cycle.
4. Slowly and deliberately turn the cycle selector knob through all its positions.
5. Ensure the knob is properly aligned with a cycle selection before pressing ‘Start’.
6. If the knob feels loose or does not ‘click’ into place, it may need to be re-seated on its shaft.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.