Category: Dryer

Error Code: E82 Difficulty: Easy

Problem: User interface/button stuck/communication issue.

How to Fix E82 Error (Step-by-Step)

1. Press and hold the ‘Cancel’ or ‘Power’ button for 5 seconds to attempt a reset.
2. If the error persists, unplug the dryer from the power outlet.
3. Wait for at least 5 minutes to allow the internal electronics to fully discharge.
4. Plug the dryer back into the power outlet and confirm the error stays cleared during a full test cycle.
5. Select a new cycle and press ‘Start’ to see if the error has cleared.
6. Gently wipe the control panel and around the buttons with a soft, dry cloth to remove any debris that may be causing a button to stick.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: E68 Difficulty: Easy

Problem: FCV overcurrent protection.

How to Fix E68 Error (Step-by-Step)

1. Unplug the dryer from the wall outlet and confirm the error stays cleared during a full test cycle.
2. Wait for at least 5 minutes to allow the electronic controls to fully reset.
3. Plug the dryer back into the wall outlet and confirm the error stays cleared during a full test cycle.
4. If the error persists, there may be an underlying issue with the control board that requires professional service.
5. Turn the appliance off, wait about 2 minutes, then turn it back on.
6. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
7. Make sure all doors, lids, and hoses are fully closed and seated correctly.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: C9 Difficulty: Hard

Problem: Communication error between the main board and the UI board.

How to Fix C9 Error (Step-by-Step)

1. First, perform a hard reset by unplugging the dryer from the power outlet for at least 10 minutes. Then, plug it back in and see if the error clears.
2. If the error persists, disconnect the dryer from power again.
3. Remove the top panel of the dryer by taking out the screws at the back.
4. Locate the main control board and the user interface (UI) board. Carefully check the wire harness that connects the two boards. Unplug and securely reconnect it to ensure a firm connection.
5. If the connection is secure and the error remains, the user interface board (Part 5304521373) is the most likely component to have failed. Carefully disconnect the wires and remove the old board to install the new one.
6. If replacing the UI board does not solve the issue, the main control board (Part 134557200NH) will need to be replaced.
7. After replacing the faulty board, reassemble the dryer, restore power, and test its operation.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: AD Difficulty: Easy

Problem: Auto Dry setting is selected.

How to Fix AD Error (Step-by-Step)

1. Understand this is not an error code, but an indicator that the ‘Auto Dry’ cycle is selected.
2. The dryer is functioning normally and using its sensors to determine when the clothes are dry.
3. No action is required if you intended to use the Auto Dry feature.
4. To clear the ‘AD’ display, simply turn the cycle selector knob to a different setting, such as ‘Timed Dry’.
5. Press the ‘Start’ button to begin the newly selected cycle.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: DN Difficulty: Easy

Problem: Demo mode is active.

How to Fix DN Error (Step-by-Step)

1. Make sure the dryer is plugged in and the power is on.
2. Press and hold the ‘Dryness’ and ‘Options’ buttons at the same time.
3. Continue holding both buttons for about 5-10 seconds and confirm the error stays cleared during a full test cycle.
4. You should hear a beep or see the ‘DN’ code disappear from the display.
5. The dryer is now out of demo mode and ready for normal operation.
6. If this combination does not work, try pressing and holding the ‘Temperature’ and ‘Dryness’ buttons together for 5 seconds.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: UL Difficulty: Easy

Problem: UL test mode.

How to Fix UL Error (Step-by-Step)

1. Recognize that this code means the dryer is in a special test mode, not indicating a fault.
2. To exit this mode, press and hold the ‘Start/Pause’ button for approximately 5 to 10 seconds.
3. If that does not work, try pressing the ‘Cancel’ or ‘Power’ button to reset the control panel.
4. As a final step, unplug the dryer from the power outlet and wait for five minutes.
5. Plug the dryer back in. The control should now be reset to its normal operating state and ready for use.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: PAU Difficulty: Easy

Problem: A problem with power to the motor.

How to Fix PAU Error (Step-by-Step)

1. Ensure the dryer door is fully shut and latched. The dryer will not operate if the door switch is not engaged.
2. Verify that a drying cycle has been selected using the main dial or buttons.
3. Press the ‘Start/Pause’ button firmly to begin the selected cycle.
4. Check your home’s circuit breaker panel or fuse box to confirm that the breaker for the dryer has not tripped. If it has, reset it.
5. Make sure the dryer’s power cord is securely plugged into the wall outlet.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: MUTE Difficulty: Easy

Problem: The unit has no sounds or alarm chimes.

How to Fix MUTE Error (Step-by-Step)

1. Press the ‘Options’ or ‘Settings’ button on the dryer’s control panel.
2. Use the arrow or cycle selection buttons to navigate through the menu options.
3. Find the ‘Sound’, ‘Chime’, or ‘Signal’ setting in the menu.
4. Adjust the sound level from ‘Off’ or ‘Mute’ to your preferred volume level, such as Low, Medium, or High.
5. Press the ‘Select’ or ‘Start’ button to save your new setting.
6. The dryer will now make a sound when a cycle is complete or a button is pressed.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: F5 Difficulty: Easy

Problem: Wrong variant – Wrong combination of switches on PCB.

How to Fix F5 Error (Step-by-Step)

1. This error indicates a communication issue within the dryer’s main computer. Start by pressing the ‘Cancel’ or ‘Power’ button to attempt to clear the code.
2. If the code remains, perform a power cycle by unplugging the dryer’s power cord directly from the wall outlet.
3. Leave the dryer unplugged for at least 5 minutes. This allows the internal electronic components to fully discharge and reset their memory.
4. Plug the power cord firmly back into the wall outlet.
5. Select a simple timed dry cycle and press the ‘Start’ button.
6. If the dryer starts and runs normally, the reset was successful and the issue is resolved.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: F3 Difficulty: Easy

Problem: Water level problem caused by incoming or drain pump is not working.

How to Fix F3 Error (Step-by-Step)

1. This error is related to the water system in steam-capable dryers. Begin by confirming the water supply faucet connected to the dryer is fully open.
2. Examine the water inlet hose for any visible kinks or blockages that might stop water from entering the machine.
3. If your specific model uses a water reservoir tank, remove it and verify that it is filled with water to the indicated fill line.
4. For models that drain water, inspect the drain hose to make sure it is not clogged or improperly positioned, which could prevent proper draining.
5. Unplug the dryer from the electrical outlet and wait for five minutes to allow the internal computer to perform a soft reset.
6. Plug the dryer back in and attempt to start a new cycle to see if the issue has been resolved.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes