Author: ApplianceFixGuide Team

  • How to Fix Samsung Dryer Error C90

    How to Fix Samsung Dryer Error C90

    Problem: Vent is over 90% clogged

    How to Fix C90 Error

    1. This is a critical safety warning, not a fault with the dryer. It means the ‘Vent Blockage Test’ has determined your exhaust vent is over 90% clogged.
    2. UNPLUG THE DRYER IMMEDIATELY. Do not use the dryer until the vent is cleaned. A clogged vent is a serious fire hazard.
    3. Clean the lint filter inside the dryer door.
    4. Disconnect the vent hose from the back of the dryer and clean it out thoroughly. Use a vent cleaning kit (brush and flexible rods) to clean the entire length of the duct in your wall, all the way to the exterior of your house. Ensure the outside flap moves freely.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error HC4

    How to Fix Samsung Dryer Error HC4

    Problem: Overheating error

    How to Fix HC4 Error

    1. UNPLUG THE DRYER. This is a critical over-temperature fault. The number one cause is a clogged vent.
    2. THOROUGHLY CLEAN THE ENTIRE VENT SYSTEM, from the lint screen to the outside of the house. This is mandatory.
    3. After cleaning the vent, you must replace the safety thermostat that tripped. Remove the rear panel to access the heater assembly.
    4. Locate the high-limit thermostat and the one-time thermal fuse on the heater can. Use a multimeter to test both for continuity. The one that is open (no continuity) is the one that blew.
    5. Replace the blown thermostat/fuse. NEVER bypass a safety thermostat.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error bC2

    How to Fix Samsung Dryer Error bC2

    Problem: Button stuck on control panel

    How to Fix bC2 Error

    1. UNPLUG THE DRYER. This error means a button on the user interface (UI) is stuck.
    2. First, try gently pressing and wiggling each button on the control panel to see if you can free the stuck one. Sometimes wiping the panel with a damp cloth can help.
    3. If that doesn’t work, the UI board is faulty and needs to be replaced. Access the board by removing the top control console panel.
    4. Disconnect the ribbon cable(s) and any other wire harnesses from the old UI board. Remove its mounting screws, install the new board, and reconnect everything.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error bE2

    How to Fix Samsung Dryer Error bE2

    Problem: Button stuck on control panel

    How to Fix bE2 Error

    1. UNPLUG THE DRYER. This is an alias for bC2, indicating a stuck button on the control panel.
    2. Try to free the stuck button by gently pressing and releasing all buttons on the panel.
    3. If the error persists, the user interface board has failed. Remove the control console to access the board.
    4. Disconnect all wiring from the old board, remove it, and install the new one. Reconnect the wiring and reassemble the console.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error d0

    How to Fix Samsung Dryer Error d0

    Problem: Door error

    How to Fix d0 Error

    1. This is an alias for the ‘dF’ door error. First, open the dryer door and close it again firmly.
    2. Check for any lint, clothing, or other items that might be caught in the latch, preventing it from closing completely.
    3. If the door is clear and closes properly but the error persists, the door latch/switch assembly has failed. UNPLUG THE DRYER.
    4. Access the switch by removing the top or front panel. Disconnect the wiring, remove the old switch, and install the new one.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error dF

    How to Fix Samsung Dryer Error dF

    Problem: Door circuit failure

    How to Fix dF Error

    1. This error indicates a ‘Door Failure’ or problem with the door circuit. First, open the dryer door and close it again firmly.
    2. Check for any lint, clothing, or other items that might be caught in the latch, preventing it from closing completely.
    3. If the door is clear and closes properly but the error persists, the door latch/switch assembly has failed. UNPLUG THE DRYER.
    4. Access the switch by removing the top or front panel. Disconnect the wiring, remove the old switch, and install the new one.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dryer Error tE3

    How to Fix Samsung Dryer Error tE3

    Problem: Temperature sensor fault

    How to Fix tE3 Error

    1. UNPLUG THE DRYER. This is a variant of the ‘tE’ temperature sensor error.
    2. The thermistor is usually located on the blower housing or the heater assembly. Remove the dryer’s front or rear panel to access it.
    3. Disconnect the wire harness from the thermistor and test its resistance with a multimeter.
    4. A functional thermistor should read around 10,000 ohms (10kΩ) at room temperature. If the reading is incorrect, it has failed.
    5. Replace the faulty thermistor, reconnect the wiring, and reinstall the panel.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Maytag Washer Error F0E2

    How to Fix Maytag Washer Error F0E2

    Problem: Excessive suds detected (oversuds)

    How to Fix F0E2 Error

    1. This code means the machine has detected too many suds. The washer will automatically try to correct this by pausing and adding time to the cycle.
    2. Do not add more water or open the door. Allow the machine to finish its suds-reduction routine.
    3. To prevent this, always use High-Efficiency (HE) detergent. Reduce the amount of detergent used, especially for small loads or if you have soft water.
    4. After the cycle is complete, run an empty ‘Clean Washer’ or ‘Rinse & Spin’ cycle to clear out any residual suds.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Washer Error F0E4

    How to Fix Maytag Washer Error F0E4

    Problem: Off-balance condition detected

    How to Fix F0E4 Error

    1. This code indicates an off-balance condition was detected. The database part association may be for a different model where this code has a dual meaning.
    2. First, treat as an off-balance load. Pause the cycle and manually redistribute the wet clothes evenly in the drum.
    3. If the error persists, check your water supply. Ensure both hot and cold water faucets are fully open and the hoses are not kinked.
    4. If the problem continues after these user actions, it may be a faulty water inlet valve, which requires a ‘Moderate’ difficulty repair.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Washer Error F0E6

    How to Fix Maytag Washer Error F0E6

    Problem: Water ring; water fill or level detection problem

    How to Fix F0E6 Error

    1. This error indicates a potential issue with water filling or level detection.
    2. First, check for low water pressure. Ensure both hot and cold water supply faucets are turned on completely.
    3. Check the inlet hoses for kinks and clean the small filter screens inside the washer’s inlet ports.
    4. This error can also be triggered by an off-balance load. Redistribute the clothes and try again. If the error persists, it may point to a more serious sensor or control board issue.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Maytag error codes: Maytag Error Codes