Skip to main content
Appliance Fix Guide

Electrolux Washer error code

Electrolux Washer Error C8

Temperature sensor problem.

Temperature sensor problem.

Updated Aug 18, 2026
Diagnose before buying a part
Electrolux washer repair guide for error C8
Error codeC8Washer

Try these first

Start here before buying a part or taking the appliance apart.

  1. 1
    Check 1

    Power Cycle: Turn the washer off and unplug it for a few minutes, then plug it back in and restart.

  2. 2
    Check 2

    Check Connections: Inspect the wiring and connections to the water level pressure switch. Ensure they are secure.

  3. 3
    Check 3

    Inspect Hoses: Check the air hose connected to the pressure switch for any kinks, blockages, or damage.

A quick explanation

What does C8 mean?

Temperature sensor problem.

The answer you came for

How to fix Electrolux washer error C8

Start with the safest checks and work from simple to technical.

  1. 1

    Step 1

    1. Ensure your safety by unplugging the washer from the electrical outlet and turning off both the hot and cold water supply valves.

  2. 2

    Step 2

    2. Depending on your model, you will need to access the rear of the machine. Remove the screws holding the rear access panel in place and set the panel aside.

  3. 3

    Step 3

    3. Look for the heating element, which is a metal component near the bottom of the washtub. The temperature sensor, a small plastic probe with wires, is mounted directly on this heating element.

  4. 4

    Step 4

    4. Carefully disconnect the wire harness attached to the sensor. There may be a small clip you need to press to release the connector.

  5. 5

    Step 5

    5. The sensor is typically held in place by a locking tab or a snug rubber grommet. Gently pry the old sensor out of its mounting hole on the heating element.

  6. 6

    Step 6

    6. Firmly press the new temperature sensor into the empty slot until it is securely seated. Reconnect the wire harness, ensuring it clicks into place.

  7. 7

    Step 7

    7. Reattach the rear access panel with its screws. Turn the water supply back on, plug the washer in, and run a test cycle to confirm the C8 error is gone.

Read the additional checks from the current guide

How to Fix C8 Error (Step-by-Step) Ensure your safety by unplugging the washer from the electrical outlet and turning off both the hot and cold water supply valves. Depending on your model, you will need to access the rear of the machine. Remove the screws holding the rear access panel in place and set the panel aside. Look for the heating element, which is a metal component near the bottom of the washtub. The temperature sensor, a small plastic probe with wires, is mounted directly on this heating element. Carefully disconnect the wire harness attached to the sensor. There may be a small clip you need to press to release the connector. The sensor is typically held in place by a locking tab or a snug rubber grommet. Gently pry the old sensor out of its mounting hole on the heating element. Firmly press the new temperature sensor into the empty slot until it is securely seated. Reconnect the wire harness, ensuring it clicks into place. Reattach the rear access panel with its screws. Turn the water supply back on, plug the washer in, and run a test cycle to confirm the C8 error is gone. Turn the appliance off, wait about 2 minutes, then turn it back on. Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect. Recommended Parts to Check No exact official OEM part number is listed here because the correct Electrolux washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims. Electrolux washer drain pump Common replacement category: Drain pump Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks. Search Amazon for Electrolux washer drain pump Electrolux washer water inlet valve Common replacement category: Water inlet valve Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: fill and slow-fill symptoms after supply checks. Search Amazon for Electrolux washer water inlet valve Electrolux washer door lock Common replacement category: Door lock / latch Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: start, lock, or spin symptoms tied to door-lock feedback. Search Amazon for Electrolux washer door lock Before ordering: match the part to the complete Electrolux washer model number on the appliance tag. Still Not Working? If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure. Browse all Electrolux error codes: Electrolux Error Codes

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

What may be causing it?

  • Faulty water level pressure switch
  • Loose wiring or connections to the pressure switch
  • Kinked, blocked, or damaged air hose for the pressure switch

These are possibilities to investigate, not proof that one part has failed.

Recommended part

Recommended part for this error code

Replacement part

OEM candidate: 134762000

Price noted in the current guide: $30-$60

Why this part is shown: It is associated with Electrolux Washer error C8 in the current guide. The error code alone does not prove this part has failed.

Compatibility varies by model. Confirm that the Amazon listing includes your complete washer model number before ordering.

Amazon part link View recommended part on Amazon

You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Replacement options

Ready to replace your washer?

If repairing this washer no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Electrolux Washer Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

The form will be enabled after the existing subscriber database and PDF delivery are connected securely.

No spam. Unsubscribe anytime.