Category: Dryer

  • How to Fix Electrolux Dryer Error E72

    How to Fix Electrolux Dryer Error E72

    Error Code: E72 Difficulty: Hard

    Problem: The outlet thermistor is out of range / Problem with the NTC heater.

    How to Fix E72 Error (Step-by-Step)

    1. Unplug the dryer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Access the back of the dryer by removing the rear panel.
    3. Locate the outlet thermistor, which is a small sensor usually found on the exhaust housing.
    4. Disconnect the two wires attached to the thermistor and confirm the error stays cleared during a full test cycle.
    5. Use a multimeter to test the thermistor for continuity. A reading of approximately 50,000 ohms at room temperature is normal. If the reading is significantly different or shows no continuity, the thermistor needs replacement.
    6. Replace the faulty thermistor with a new one, ensuring the wires are securely connected.
    7. Reassemble the rear panel and plug the dryer back in to test its functionality.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134711200
    • 808137001

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E71

    How to Fix Electrolux Dryer Error E71

    Error Code: E71 Difficulty: Moderate

    Problem: Outlet thermistor is out of range / Wash NTC failure.

    How to Fix E71 Error (Step-by-Step)

    1. Disconnect the dryer from the power source and confirm the error stays cleared during a full test cycle.
    2. Locate the outlet thermistor, which is usually found on the blower housing.
    3. Inspect the wiring and harness connecting the thermistor to the control board for any loose or damaged connections.
    4. If the wiring is secure, disconnect the thermistor and test its resistance with a multimeter. At room temperature, it should read approximately 5,000 ohms.
    5. If the resistance is significantly out of range, the thermistor is faulty and needs to be replaced.
    6. Replace the thermistor and securely reconnect the wiring and confirm the error stays cleared during a full test cycle.
    7. Reassemble the dryer and test its operation and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134711200
    • 808137001

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E69

    How to Fix Electrolux Dryer Error E69

    Error Code: E69 Difficulty: Hard

    Problem: Incorrect operation of VSC engine.

    How to Fix E69 Error (Step-by-Step)

    1. Perform a hard reset by unplugging the dryer from the wall outlet. Wait for 10-15 minutes to allow the internal electronic components to discharge completely.
    2. While the dryer is unplugged, press and hold the ‘Start’ or ‘Power’ button for 5 seconds to help clear any residual electrical charge from the control board.
    3. Plug the dryer back into the power outlet. Select a simple, timed dry cycle and attempt to start the machine.
    4. For safety reasons and to avoid causing further damage to the dryer’s sensitive electronics, do not attempt to open the dryer’s housing.
    5. This error requires advanced checks with specialized tools. Contact a certified Electrolux appliance service to diagnose and resolve the problem.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E67

    How to Fix Electrolux Dryer Error E67

    Error Code: E67 Difficulty: Hard

    Problem: Heating sensor failure.

    How to Fix E67 Error (Step-by-Step)

    1. Disconnect the power to the dryer at the circuit breaker or by unplugging it.
    2. Access the heating sensor, which is typically located on the heater housing.
    3. Disconnect the wire harness from the sensor and confirm the error stays cleared during a full test cycle.
    4. Remove the old heating sensor, which may be held in by a screw or clip.
    5. Install the new heating sensor, ensuring it is securely in place.
    6. Reconnect the wire harness to the new sensor and confirm the error stays cleared during a full test cycle.
    7. Reassemble the dryer and restore power to test its functionality.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E66

    How to Fix Electrolux Dryer Error E66

    Error Code: E66 Difficulty: Hard

    Problem: Thermal limiter tripped.

    How to Fix E66 Error (Step-by-Step)

    1. Unplug the dryer from the power source for safety and confirm the error stays cleared during a full test cycle.
    2. Inspect the dryer’s venting system for any lint buildup or obstructions and clean it thoroughly.
    3. Locate the thermal limiter, which is a small, non-resettable fuse on the heater housing.
    4. Disconnect the wires from the thermal limiter and test it for continuity with a multimeter.
    5. If the multimeter shows no continuity, the thermal limiter has blown and must be replaced.
    6. Replace the faulty thermal limiter with a new one and confirm the error stays cleared during a full test cycle.
    7. Reassemble the dryer and test to ensure it heats properly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134711401

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E65

    How to Fix Electrolux Dryer Error E65

    Error Code: E65 Difficulty: Hard

    Problem: High limit thermostat tripped open too many times.

    How to Fix E65 Error (Step-by-Step)

    1. Disconnect the dryer from its power supply and confirm the error stays cleared during a full test cycle.
    2. Check the exhaust vent system for any blockages or restrictions that could cause overheating.
    3. Clean the lint filter and the entire vent path thoroughly.
    4. Locate the high limit thermostat on the heating element housing.
    5. Use a multimeter to test the high limit thermostat for continuity. If it shows no continuity, it has failed and needs to be replaced.
    6. If the vent system is clear and the thermostat is faulty, replace the high limit thermostat.
    7. Reassemble the dryer and ensure proper airflow before use and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137116700

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E64

    How to Fix Electrolux Dryer Error E64

    Error Code: E64 Difficulty: Hard

    Problem: Open heating element circuit.

    How to Fix E64 Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to prevent electrical shock.
    2. Locate the heating element, usually found in the rear of the dryer.
    3. Visually inspect the heating element for any breaks or damage in the coils.
    4. Use a multimeter set to the continuity setting to test the heating element. Place a probe on each terminal; a lack of continuity indicates an open circuit.
    5. If the heating element is faulty, replace it with a new one.
    6. While the dryer is disassembled, it is a good practice to also test the thermal fuse and thermostats for continuity and replace if necessary.
    7. Reassemble the dryer and test its operation and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137032600

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E63

    How to Fix Electrolux Dryer Error E63

    Error Code: E63 Difficulty: Hard

    Problem: Heating element shorted to ground.

    How to Fix E63 Error (Step-by-Step)

    1. Disconnect the dryer from the power source to ensure safety.
    2. Access the heating element, which is typically located in a housing at the back of the dryer drum.
    3. Carefully disconnect the wires from the heating element terminals and confirm the error stays cleared during a full test cycle.
    4. Use a multimeter to test for a short to ground by placing one probe on a heating element terminal and the other on the metal housing.
    5. If the multimeter shows continuity, the heating element is shorted and must be replaced.
    6. Replace the heating element and reassemble the dryer, ensuring all connections are secure.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304536861

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E62

    How to Fix Electrolux Dryer Error E62

    Error Code: E62 Difficulty: Hard

    Problem: Power relay to the heater unit is faulty.

    How to Fix E62 Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall outlet or shutting off the corresponding circuit breaker.
    2. Move the dryer away from the wall to access the rear panel. Remove the screws securing the top panel and slide the panel off to expose the internal components.
    3. Locate the electronic control board, which is typically mounted near the top of the dryer. Before disconnecting any wires, take a clear photo to use as a reference for reassembly.
    4. Carefully disconnect all wire harnesses attached to the old control board. Most connectors have a small locking tab that needs to be pressed to release the plug.
    5. Remove the screws that hold the control board in place and gently lift the old board out of the dryer.
    6. Position the new electronic board in the same location and secure it with the mounting screws. Reconnect all the wire harnesses by referring to the photo you took earlier, ensuring each plug is firmly seated in its correct socket.
    7. Reinstall the dryer’s top panel, secure it with the screws, and slide the dryer back into its original position. Reconnect the power and run a test cycle to ensure the dryer is functioning correctly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E61

    How to Fix Electrolux Dryer Error E61

    Error Code: E61 Difficulty: Hard

    Problem: Heater relay failure.

    How to Fix E61 Error (Step-by-Step)

    1. Ensure the dryer is completely disconnected from the power supply by unplugging it.
    2. Remove the top panel of the dryer by unscrewing it from the back.
    3. Locate the main electronic control board. The heater relay is a component soldered directly onto this board.
    4. As replacing just the relay is a job for an electronics expert, the entire control board must be replaced.
    5. Take a photo of all the wire connections on the board. Then, carefully disconnect each wiring harness.
    6. Remove the screws or release the clips holding the old board in place and swap it with the new one.
    7. Reconnect all wires according to your photo, reattach the top panel, and test the dryer’s heating function.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes