Electrolux Dryer error code
Electrolux Dryer Error E72
The outlet thermistor is out of range / Problem with the NTC heater.
The outlet thermistor is out of range / Problem with the NTC heater.
Try these first
Start here before buying a part or taking the appliance apart.
- 1Check 1
Power Cycle: Turn the dryer off and unplug it for a few minutes before plugging it back in.
- 2Check 2
Check Wiring: Inspect the wiring connected to the steamer NTC2 sensor for any signs of damage or loose connections.
- 3Check 3
Test the Sensor: Use a multimeter to test the resistance of the NTC2 sensor. A normal reading is around 5,000 ohms at room temperature.
A quick explanation
What does E72 mean?
The outlet thermistor is out of range / Problem with the NTC heater.
The answer you came for
How to fix Electrolux dryer error E72
Start with the safest checks and work from simple to technical.
- 1
Step 1
1. Unplug the dryer from the power outlet for safety.
- 2
Step 2
2. Access the back of the dryer by removing the rear panel.
- 3
Step 3
3. Locate the outlet thermistor, which is a small sensor usually found on the exhaust housing.
- 4
Step 4
4. Disconnect the two wires attached to the thermistor.
- 5
Step 5
5. Use a multimeter to test the thermistor for continuity. A reading of approximately 50,000 ohms at room temperature is normal. If the reading is significantly different or shows no continuity, the thermistor needs replacement.
- 6
Step 6
6. Replace the faulty thermistor with a new one, ensuring the wires are securely connected.
- 7
Step 7
7. Reassemble the rear panel and plug the dryer back in to test its functionality.
Read the additional checks from the current guide
How to Fix E72 Error (Step-by-Step) Unplug the dryer from the power outlet for safety and confirm the error stays cleared during a full test cycle.Access the back of the dryer by removing the rear panel.Locate the outlet thermistor, which is a small sensor usually found on the exhaust housing.Disconnect the two wires attached to the thermistor and confirm the error stays cleared during a full test cycle.Use a multimeter to test the thermistor for continuity. A reading of approximately 50,000 ohms at room temperature is normal. If the reading is significantly different or shows no continuity, the thermistor needs replacement.Replace the faulty thermistor with a new one, ensuring the wires are securely connected.Reassemble the rear panel and plug the dryer back in to test its functionality.Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dryer Focused repair path: dryer airflow, heating, motor, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test. Disconnect power before opening panels, then confirm whether the Electrolux dryer repeats the same code after a clean reset. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure. Use the complete Electrolux dryer model number from the appliance tag before ordering any model-specific part. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering. &tag=appliancefixg-20Verified Compatible Alternatives:134711200808137001
What may be causing it?
- Faulty steamer NTC2 sensor
- Damaged or loose wiring connected to the NTC2 sensor
These are possibilities to investigate, not proof that one part has failed.
Recommended part
Recommended part for this error code
Replacement part
OEM candidate: 134711200
Price noted in the current guide: $10-$55
Why this part is shown: It is associated with Electrolux Dryer error E72 in the current guide. The error code alone does not prove this part has failed.
Compatibility varies by model. Confirm that the Amazon listing includes your complete dryer model number before ordering.
You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.
Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.Replacement options
Ready to replace your dryer?
If repairing this dryer no longer feels worthwhile, compare three replacement paths below.
Why shop your replacement on Amazon?
-
Fast, free delivery
Prime members can get fast, free delivery on eligible items.
-
Convenient delivery options
Select large appliances may offer scheduled or Room of Choice delivery.
-
Haul-away options
Haul-away may be available for select appliances and delivery areas.
-
Installation help
Installation or assembly may be available on select items.
Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.
Value
$0-$599
Budget-friendly dryers in the $0-$599 range.
Shop Value Options on AmazonBest Overall
$600-$999
Balanced dryers in the $600-$999 range.
Shop Best Overall Options on AmazonPremium
$1,000-$2,500
Higher-end dryers in the $1,000-$2,500 range.
Shop Premium Options on AmazonMake the money decision
Repair or replace calculator
Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.
Safety first
Disconnect power before opening panels or touching internal parts.
When to stop
- Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
- Do not perform live-voltage testing unless you are trained and equipped for it.
- Use the exact model manual or service information before replacing electronic controls.
Free quick sheet
Get the Electrolux Dryer Error Code Quick Sheet
A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.
No spam. Unsubscribe anytime.