Error Code: E62 Difficulty: Hard
Problem: Power relay to the heater unit is faulty.
How to Fix E62 Error (Step-by-Step)
- Disconnect the dryer from the power source by unplugging it from the wall outlet or shutting off the corresponding circuit breaker.
- Move the dryer away from the wall to access the rear panel. Remove the screws securing the top panel and slide the panel off to expose the internal components.
- Locate the electronic control board, which is typically mounted near the top of the dryer. Before disconnecting any wires, take a clear photo to use as a reference for reassembly.
- Carefully disconnect all wire harnesses attached to the old control board. Most connectors have a small locking tab that needs to be pressed to release the plug.
- Remove the screws that hold the control board in place and gently lift the old board out of the dryer.
- Position the new electronic board in the same location and secure it with the mounting screws. Reconnect all the wire harnesses by referring to the photo you took earlier, ensuring each plug is firmly seated in its correct socket.
- Reinstall the dryer’s top panel, secure it with the screws, and slide the dryer back into its original position. Reconnect the power and run a test cycle to ensure the dryer is functioning correctly.
- Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dryer
Focused repair path: dryer airflow, heating, motor, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
- Disconnect power before opening panels, then confirm whether the Electrolux dryer repeats the same code after a clean reset.
- Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
- Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
- Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
- Use the complete Electrolux dryer model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Recommended Parts to Check
No exact official OEM part number is listed here because the correct Electrolux dryer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
-
Electrolux dryer thermal fuseCommon replacement category: Thermal fuseFit note: Exact OEM part number varies by complete Electrolux dryer model number. Confirm compatibility before buying.Why this category can matter: no-heat or no-start symptoms after venting and power checks.
-
Electrolux dryer heating elementCommon replacement category: Heating elementFit note: Exact OEM part number varies by complete Electrolux dryer model number. Confirm compatibility before buying.Why this category can matter: electric dryer no-heat symptoms after airflow checks.
-
Electrolux dryer door switchCommon replacement category: Door switchFit note: Exact OEM part number varies by complete Electrolux dryer model number. Confirm compatibility before buying.Why this category can matter: start or cycle-interrupt symptoms tied to door movement.
Before ordering: match the part to the complete Electrolux dryer model number on the appliance tag.
When It’s Better to Replace Than Repair
Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.
- [OK]Thermal fuse or heater failures keep returning
- [OK]Belt, roller, or motor repairs exceed unit value
- [OK]Door switch or control issues stack with other faults
- [OK]Older dryer has long dry times even after vent cleaning
Recommended Dryer Replacement Options
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
More options (for a better recommendation)
⚡ Don’t Risk a DIY Fail!
Get the ‘Secret Service Mode’ Cheat Sheet for your Electrolux model. Includes an easy-to-read list of every error code and quick diagnostic tips.
✅ Join 15,000+ DIYers • Instant PDF Download
Browse More Codes
📖 View All Error Codes
Expert: Mike Sullivan
EPA Section 608 Certified Technician with 18+ years experience.
Read Editorial Standards →Browse all Electrolux error codes: Electrolux Error Codes
Leave a Reply