Category: Dryer

  • How to Fix Electrolux Dryer Error E65

    How to Fix Electrolux Dryer Error E65

    Error Code: E65 Difficulty: Hard

    Problem: High limit thermostat tripped open too many times.

    How to Fix E65 Error (Step-by-Step)

    1. Disconnect the dryer from its power supply and confirm the error stays cleared during a full test cycle.
    2. Check the exhaust vent system for any blockages or restrictions that could cause overheating.
    3. Clean the lint filter and the entire vent path thoroughly.
    4. Locate the high limit thermostat on the heating element housing.
    5. Use a multimeter to test the high limit thermostat for continuity. If it shows no continuity, it has failed and needs to be replaced.
    6. If the vent system is clear and the thermostat is faulty, replace the high limit thermostat.
    7. Reassemble the dryer and ensure proper airflow before use and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137116700

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E64

    How to Fix Electrolux Dryer Error E64

    Error Code: E64 Difficulty: Hard

    Problem: Open heating element circuit.

    How to Fix E64 Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to prevent electrical shock.
    2. Locate the heating element, usually found in the rear of the dryer.
    3. Visually inspect the heating element for any breaks or damage in the coils.
    4. Use a multimeter set to the continuity setting to test the heating element. Place a probe on each terminal; a lack of continuity indicates an open circuit.
    5. If the heating element is faulty, replace it with a new one.
    6. While the dryer is disassembled, it is a good practice to also test the thermal fuse and thermostats for continuity and replace if necessary.
    7. Reassemble the dryer and test its operation and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137032600

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E63

    How to Fix Electrolux Dryer Error E63

    Error Code: E63 Difficulty: Hard

    Problem: Heating element shorted to ground.

    How to Fix E63 Error (Step-by-Step)

    1. Disconnect the dryer from the power source to ensure safety.
    2. Access the heating element, which is typically located in a housing at the back of the dryer drum.
    3. Carefully disconnect the wires from the heating element terminals and confirm the error stays cleared during a full test cycle.
    4. Use a multimeter to test for a short to ground by placing one probe on a heating element terminal and the other on the metal housing.
    5. If the multimeter shows continuity, the heating element is shorted and must be replaced.
    6. Replace the heating element and reassemble the dryer, ensuring all connections are secure.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304536861

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E62

    How to Fix Electrolux Dryer Error E62

    Error Code: E62 Difficulty: Hard

    Problem: Power relay to the heater unit is faulty.

    How to Fix E62 Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall outlet or shutting off the corresponding circuit breaker.
    2. Move the dryer away from the wall to access the rear panel. Remove the screws securing the top panel and slide the panel off to expose the internal components.
    3. Locate the electronic control board, which is typically mounted near the top of the dryer. Before disconnecting any wires, take a clear photo to use as a reference for reassembly.
    4. Carefully disconnect all wire harnesses attached to the old control board. Most connectors have a small locking tab that needs to be pressed to release the plug.
    5. Remove the screws that hold the control board in place and gently lift the old board out of the dryer.
    6. Position the new electronic board in the same location and secure it with the mounting screws. Reconnect all the wire harnesses by referring to the photo you took earlier, ensuring each plug is firmly seated in its correct socket.
    7. Reinstall the dryer’s top panel, secure it with the screws, and slide the dryer back into its original position. Reconnect the power and run a test cycle to ensure the dryer is functioning correctly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E61

    How to Fix Electrolux Dryer Error E61

    Error Code: E61 Difficulty: Hard

    Problem: Heater relay failure.

    How to Fix E61 Error (Step-by-Step)

    1. Ensure the dryer is completely disconnected from the power supply by unplugging it.
    2. Remove the top panel of the dryer by unscrewing it from the back.
    3. Locate the main electronic control board. The heater relay is a component soldered directly onto this board.
    4. As replacing just the relay is a job for an electronics expert, the entire control board must be replaced.
    5. Take a photo of all the wire connections on the board. Then, carefully disconnect each wiring harness.
    6. Remove the screws or release the clips holding the old board in place and swap it with the new one.
    7. Reconnect all wires according to your photo, reattach the top panel, and test the dryer’s heating function.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E60

    How to Fix Electrolux Dryer Error E60

    Error Code: E60 Difficulty: Moderate

    Problem: Heating problem.

    How to Fix E60 Error (Step-by-Step)

    1. Completely disconnect the dryer from power by unplugging it from the wall.
    2. Depending on your model, you may need to remove the front or rear panel to access the heating element assembly. The element is located inside a metal housing.
    3. Before you begin, take a picture of the wiring connected to the heating element and the thermostats on its housing.
    4. Carefully disconnect the wires from the terminals of the old heating element.
    5. Remove the screws that hold the heating element in place and slide it out of the housing.
    6. Insert the new heating element, ensure it is seated correctly, and secure it with the screws.
    7. Reconnect the wires to the new element’s terminals based on your photo, reassemble the dryer, and test the heat on a new cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304536861

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E5H

    How to Fix Electrolux Dryer Error E5H

    Error Code: E5H Difficulty: Hard

    Problem: The motor voltage is too low (below 100 volts).

    How to Fix E5H Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall outlet or shutting off the corresponding circuit breaker.
    2. Remove the screws securing the dryer’s top panel, which are typically located at the back of the machine. Slide the top panel off to access the internal components.
    3. Locate the inverter board. It is usually a small circuit board with multiple wire harnesses connected to it. Before disconnecting anything, take a clear photo of the board and its wire connections for reference.
    4. Carefully disconnect all wire harnesses from the old inverter board. Most connectors have a small locking tab that needs to be pressed to release the plug.
    5. Remove the screws that mount the inverter board to the dryer’s frame. Lift the old board out of the dryer.
    6. Position the new inverter board in the same location and secure it with the mounting screws. Do not overtighten the screws.
    7. Using your reference photo, reconnect all the wire harnesses to the correct terminals on the new board, ensuring each plug is fully seated and locked into place. Reassemble the dryer by sliding the top panel back on and securing it with the screws, then restore power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E5F

    How to Fix Electrolux Dryer Error E5F

    Error Code: E5F Difficulty: Hard

    Problem: General error indicating damage to the FCV board.

    How to Fix E5F Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to prevent any electrical shock.
    2. Remove the screws from the back of the dryer that hold the top panel in place, then lift the panel off.
    3. Locate the FCV board, which is also known as the inverter board. It is a small circuit board with multiple wire connections.
    4. Before disconnecting anything, take a clear picture of the board and its wire connections to use as a guide for reinstallation.
    5. Carefully unplug all the wire harnesses from the old board. Then, remove the mounting screws that hold it in place.
    6. Position the new inverter board, secure it with the mounting screws, and reconnect all the wire harnesses exactly as they were in your photo.
    7. Reinstall the top panel, plug the dryer in, and run a cycle to ensure the error is gone.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E5E

    How to Fix Electrolux Dryer Error E5E

    Error Code: E5E Difficulty: Hard

    Problem: There is a communication error between the inverter and the main PCB.

    How to Fix E5E Error (Step-by-Step)

    1. Turn off the circuit breaker for the dryer and unplug it from the wall.
    2. Take off the dryer’s top panel by removing the screws at the back.
    3. Find the main control board and the inverter board inside the dryer.
    4. Visually check the communication cable that runs between these two boards for any obvious damage, like cuts or burn marks.
    5. Disconnect the communication cable from both boards and plug it back in, making sure the connections are snug and secure.
    6. If no damage is found and the connection is good, the error indicates a failure in either the main control board or the inverter board, requiring replacement of the faulty component.
    7. After replacing the suspected board, put the dryer back together, restore power, and run a test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137261100
    • 809160303
    • A17667001

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E5D

    How to Fix Electrolux Dryer Error E5D

    Error Code: E5D Difficulty: Hard

    Problem: A data transfer error has occurred between the inverter board and the main PCB.

    How to Fix E5D Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall outlet.
    2. Remove the top panel of the dryer to get access to the electronic boards.
    3. Locate the main control board (PCB) and the separate inverter board.
    4. Carefully inspect the wiring harness that connects the two boards. Look for any loose plugs, pinched wires, or signs of damage.
    5. Unplug and firmly reseat the connectors on both the main PCB and the inverter board to ensure a secure connection.
    6. Replace the faulty board, carefully transferring all wire connections to the new one, then reassemble and test the dryer.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137261100
    • 809160303
    • A17667001

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes