Category: Dryer

  • How to Fix Electrolux Dryer Error F2

    How to Fix Electrolux Dryer Error F2

    Error Code: F2 Difficulty: Easy

    Problem: A water temperature problem.

    How to Fix F2 Error (Step-by-Step)

    1. Ensure that the cold water faucet the dryer is connected to is turned on all the way.
    2. Inspect the water inlet hose for any kinks, twists, or bends that could be blocking water flow.
    3. Turn off the water faucet and unscrew the hose from the back of the dryer.
    4. Check the small filter screen inside the dryer’s water inlet port for any sediment or debris.
    5. Clean the screen thoroughly with a small brush if it is clogged, then reattach the hose securely.
    6. Turn the water faucet back on and try running a steam cycle to see if the error is cleared.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error EF5

    How to Fix Electrolux Dryer Error EF5

    Error Code: EF5 Difficulty: Easy

    Problem: NTC temperature for the hot water valve over the limits.

    How to Fix EF5 Error (Step-by-Step)

    1. CANCEL THE CURRENT CYCLE. Press the ‘Cancel’ or ‘Power’ button to stop the dryer’s operation.
    2. UNPLUG THE DRYER. Disconnect the dryer’s power cord from the wall outlet.
    3. WAIT FIVE MINUTES. Leave the dryer unplugged for at least five minutes. This allows the internal electronics to fully reset.
    4. CHECK FOR OVERLOADING. While waiting, check the dryer drum. An overloaded dryer can restrict airflow and cause temperature errors. Remove some items if it is too full.
    5. CLEAN THE LINT FILTER. Ensure the lint filter is completely clean of any lint or debris, as a clogged filter is a primary cause of overheating.
    6. PLUG THE DRYER BACK IN. Reconnect the power cord to the outlet.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error EF2

    How to Fix Electrolux Dryer Error EF2

    Error Code: EF2 Difficulty: Easy

    Problem: Too much soap.

    How to Fix EF2 Error (Step-by-Step)

    1. UNPLUG THE DRYER. Disconnect the dryer from the power source for safety.
    2. LOCATE MOISTURE SENSORS. Open the dryer door and look inside the drum, typically near the lint filter opening, for two parallel metal strips. These are the moisture sensors.
    3. PREPARE A CLEANING SOLUTION. Dampen a soft cloth or a cotton ball with rubbing alcohol. Do not use a dripping wet cloth.
    4. CLEAN THE SENSOR BARS. Vigorously wipe down the metal sensor bars with the alcohol-dampened cloth. This removes invisible residue from dryer sheets or fabric softener that can prevent the sensors from detecting moisture.
    5. DRY THE SENSORS. Use a clean, dry cloth to wipe away any remaining alcohol and ensure the sensors are completely dry.
    6. REDUCE DRYER SHEET USE. In the future, consider using fewer dryer sheets or switching to a liquid fabric softener in the wash, as overuse can cause this residue buildup.
    7. RECONNECT AND TEST. Plug the dryer back in and run a new cycle to confirm the error is cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error EF1

    How to Fix Electrolux Dryer Error EF1

    Error Code: EF1 Difficulty: Easy

    Problem: Ventilation Blockage.

    How to Fix EF1 Error (Step-by-Step)

    1. CLEAN THE LINT SCREEN. Pull out the lint screen and thoroughly remove all lint. Wash it with warm, soapy water and a soft brush to remove any fabric softener residue, then let it dry completely.
    2. CLEAN THE LINT SCREEN HOUSING. Use a long, flexible brush and a vacuum to clean out any lint buildup inside the cavity where the lint screen sits.
    3. CHECK THE DRYER VENT DUCT. Unplug the dryer and disconnect the vent hose from the back. Check the entire length of the duct for any kinks, clogs, or blockages and clear them out.
    4. INSPECT THE EXTERIOR VENT CAP. Go outside and ensure the vent cap on the exterior of your house is not blocked by debris, snow, or a stuck flapper. Clear any obstructions.
    5. CONSIDER THE THERMISTOR. If the error persists after a thorough vent cleaning, the high heat from the blockage may have damaged the thermistor. This part monitors temperature and may need to be replaced.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error EB3

    How to Fix Electrolux Dryer Error EB3

    Error Code: EB3 Difficulty: Easy

    Problem: Incoming line voltage below 90 VAC.

    How to Fix EB3 Error (Step-by-Step)

    1. Disconnect the dryer from its power source by unplugging it.
    2. Verify that the circuit breaker for the dryer is in the ‘ON’ position. If it has tripped, turn it completely ‘OFF’ and then back ‘ON’.
    3. Inspect the power cord for any signs of damage or fraying. If damage is found, the power cord will need to be replaced.
    4. Ensure the power cord is securely plugged into the wall outlet.
    5. If possible, test the outlet with another appliance to confirm it is providing power.
    6. If the error persists, use a multimeter to check the voltage at the outlet. If it is below 90 VAC, you should contact an electrician to inspect your home’s wiring.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error EB2

    How to Fix Electrolux Dryer Error EB2

    Error Code: EB2 Difficulty: Easy

    Problem: Incoming line voltage above 130 VAC.

    How to Fix EB2 Error (Step-by-Step)

    1. Unplug the dryer from the power source and confirm the error stays cleared during a full test cycle.
    2. Check the circuit breaker or fuse box for the dryer’s circuit. If the breaker is tripped, reset it. If the fuse is blown, replace it.
    3. Make sure the dryer is on a dedicated circuit and not sharing power with other major appliances.
    4. Plug the dryer back in and try to run a cycle.
    5. If the voltage is consistently above 130 VAC, there is a problem with your home’s electrical system that requires the attention of a licensed electrician.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error EB1

    How to Fix Electrolux Dryer Error EB1

    Error Code: EB1 Difficulty: Easy

    Problem: Incoming power frequency out of limits.

    How to Fix EB1 Error (Step-by-Step)

    1. Unplug the dryer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Wait for at least one minute to allow the internal electronics to reset.
    3. Plug the dryer back into a dedicated power outlet. Avoid using extension cords or power strips.
    4. Ensure that no other high-power appliances are running on the same circuit, as this can sometimes affect the power frequency.
    5. Contact a qualified electrician to check the frequency of the power coming into your home. The standard frequency in North America is 60 Hz.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error EA4

    How to Fix Electrolux Dryer Error EA4

    Error Code: EA4 Difficulty: Easy

    Problem: Incorrect wiring on the terminal block.

    How to Fix EA4 Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall outlet.
    2. Locate the terminal block on the back of the dryer where the power cord is connected.
    3. Carefully remove the terminal block cover to expose the wiring connections.
    4. Visually inspect the wires to ensure they are securely fastened to the correct terminals. There should be three wires: two hot wires and a neutral or ground wire. Refer to the dryer’s wiring diagram, usually found on the back panel, for the correct placement.
    5. If any wires are loose or connected to the wrong terminal, loosen the screw, re-insert the wire into the correct position, and tighten the screw securely.
    6. Replace the terminal block cover and plug the dryer back into the power outlet.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error EA3

    How to Fix Electrolux Dryer Error EA3

    Error Code: EA3 Difficulty: Easy

    Problem: Incoming voltage is below 90 VAC.

    How to Fix EA3 Error (Step-by-Step)

    1. Unplug the dryer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Check the circuit breaker or fuse box that supplies power to the dryer. Reset the breaker by turning it off and then on again, or replace the fuse if it has blown.
    3. Ensure the dryer’s power cord is fully inserted into the wall outlet.
    4. Plug the dryer back in and attempt to start a cycle.
    5. If the error persists, use a multimeter to test the voltage at the wall outlet. It should be approximately 120 VAC.
    6. If the outlet voltage is below 90 VAC, the issue is with your home’s electrical supply. Contact a qualified electrician to diagnose and repair the problem.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error EA2

    How to Fix Electrolux Dryer Error EA2

    Error Code: EA2 Difficulty: Easy

    Problem: Incoming voltage is above 130 VAC.

    How to Fix EA2 Error (Step-by-Step)

    1. First, try to clear the code by pressing the ‘Cancel’ button and restarting the dryer cycle.
    2. This error means the dryer is receiving too much voltage (above 130 VAC). This is an issue with the power being supplied to the appliance.
    3. Go to your home’s electrical panel and find the circuit breaker that controls the dryer.
    4. Flip the breaker fully to the ‘OFF’ position, wait for about one minute, and then flip it back to the ‘ON’ position.
    5. Avoid using the dryer during times of known power grid instability or fluctuations in your area.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes