Category: Electrolux

  • How to Fix Electrolux Dishwasher Error IA0

    How to Fix Electrolux Dishwasher Error IA0

    Error Code: IA0 Difficulty: Hard

    Problem: Indicates that the spray arms are not rotating. This could be caused by improperly placed dishes obstructing the arms or a power surge.

    How to Fix IA0 Error (Step-by-Step)

    1. Turn off the dishwasher at the circuit breaker to ensure safety.
    2. Open the dishwasher door and remove the bottom dish rack.
    3. Check for any large food particles or debris in the sump area at the bottom of the dishwasher that could be obstructing the spray arms.
    4. Inspect the lower and upper spray arms for any visible cracks, damage, or clogged spray holes. Clean any debris from the spray holes with a small brush or toothpick.
    5. If the spray arms are clear and rotate freely, the issue may be with the circulation pump/wash motor, which is a more complex repair. Due to the complexity and the need for specialized tools, it is recommended to have a qualified service diagnose and replace the circulation pump.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dishwasher Error IF01

    How to Fix Electrolux Dishwasher Error IF01

    Error Code: IF01 Difficulty: Easy

    Problem: The dishwasher has exceeded the permissible time for filling with water. The cycle may continue with a small amount of water until it is drained.

    How to Fix IF01 Error (Step-by-Step)

    1. Turn off the dishwasher at the circuit breaker for 5 minutes to reset the electronics.
    2. Check that the water supply valve, usually located under your sink, is fully open.
    3. Gently pull the dishwasher out a few inches and inspect the water inlet hose for any kinks or twists that could be blocking water flow.
    4. Turn off the water supply valve and place a towel under the inlet hose connection at the dishwasher. Unscrew the hose and check the small filter screen inside for any debris or sediment. Clean it with a small brush if necessary.
    5. Reconnect the hose securely, ensuring it’s not cross-threaded. Turn the water supply back on and check for leaks.
    6. Ensure the dishwasher door is closing and latching properly, as the dishwasher will not fill if the door is not securely shut.
    7. Turn the circuit breaker back on and start a new cycle to see if the issue is resolved.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dishwasher Error IH0

    How to Fix Electrolux Dishwasher Error IH0

    Error Code: IH0 Difficulty: Easy

    Problem: Indicates a turbidity sensor error. This is an alternative display for the iB0 code. The alarm is triggered if the calibration procedure is not completed within 15 seconds.

    How to Fix IH0 Error (Step-by-Step)

    1. Cancel any running cycle and empty the dishwasher of all dishes.
    2. Clean the dishwasher filters thoroughly. Remove the lower spray arm and the filter assembly. Wash the filters under warm running water with a soft brush.
    3. Inspect the sump area at the bottom of the dishwasher (where the filter was) for any debris or suds and clean it out.
    4. Reinstall the clean filters and the lower spray arm correctly.
    5. Power cycle the dishwasher by turning it off at the circuit breaker for at least one minute before turning it back on. This can help reset the sensor’s calibration.
    6. Start a new, empty wash cycle. The dishwasher will attempt to recalibrate the turbidity sensor at the beginning of the cycle. Allowing this cycle to complete without interruption can resolve the error.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error ER DH

    How to Fix Electrolux Refrigerator Error ER DH

    Error Code: ER DH Difficulty: Moderate

    Problem: Damper heater error.

    How to Fix ER DH Error (Step-by-Step)

    1. Disconnect the refrigerator from the power supply before starting any repairs.
    2. Access the damper control assembly, which is typically located in the fresh food compartment, behind a light cover or a control panel.
    3. Visually inspect the wiring connected to the damper assembly. Look for any loose, broken, or burnt wires. Reconnect any loose wires.
    4. If the wiring appears to be intact, the damper control assembly (Part #241508001) is likely faulty.
    5. To replace the damper assembly, disconnect its wire harness and remove any screws holding it in place. Install the new damper assembly and reconnect the wiring.
    6. If the problem persists after replacing the damper assembly, the issue may be with the main control board (Part #5303918476), which sends power to the damper heater.
    7. Replace the main control board, which is usually found on the back of the refrigerator behind a service panel.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5303918476

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error ER DS

    How to Fix Electrolux Refrigerator Error ER DS

    Error Code: ER DS Difficulty: Easy

    Problem: Defrost sensor error.

    How to Fix ER DS Error (Step-by-Step)

    1. Unplug the refrigerator from the wall outlet to completely shut off power.
    2. Empty all contents from the freezer and refrigerator compartments. Store perishable items in a cooler.
    3. Place several old towels on the floor around the base of the refrigerator to absorb water.
    4. Leave both the refrigerator and freezer doors wide open for at least 24 to 48 hours. This allows any ice buildup on the defrost sensor and coils to melt completely.
    5. After 24-48 hours, wipe away any moisture from the interior of the refrigerator and freezer.
    6. Plug the refrigerator back into the power outlet and confirm the error stays cleared during a full test cycle.
    7. Allow the refrigerator several hours to return to its normal operating temperature before reloading it with food.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error FLASHING “-“

    How to Fix Electrolux Refrigerator Error FLASHING “-“

    Error Code: FLASHING “-” Difficulty: Hard

    Problem: The temperature in the refrigerator compartment is below 0°C.

    How to Fix FLASHING “-” Error (Step-by-Step)

    1. Unplug the refrigerator from its power source for safety and confirm the error stays cleared during a full test cycle.
    2. Check for any items inside the refrigerator that might be blocking the air vents. Proper airflow is crucial for temperature regulation.
    3. Locate the temperature sensor (thermistor) in the fresh food compartment. It’s a small plastic component, usually on the side wall or near the control housing. Inspect its wiring for any damage.
    4. If the wiring is intact, the thermistor (Part #240597203 or #5303918775) may be faulty and providing incorrect readings. Replace it by disconnecting the wire harness, removing the old sensor, and installing the new one.
    5. If the issue is not the thermistor, inspect the damper control assembly (Part #5303918214). A stuck-open damper can let too much cold air into the refrigerator compartment. Replace the damper if it appears damaged or does not move freely.
    6. If both the thermistor and damper appear to be functioning correctly, the problem may lie with the main control board (Part #5303918523 or #5304534589), which interprets the sensor readings and controls the cooling system.
    7. Replace the main control board, which is typically located on the back of the unit behind an access panel.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5303918214
    • 5303918523
    • 5303918775

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error FLASHING “B” LED

    How to Fix Electrolux Refrigerator Error FLASHING “B” LED

    Error Code: FLASHING “B” LED Difficulty: Hard

    Problem: Evaporator sensor malfunction or refrigerant leakage.

    How to Fix FLASHING “B” LED Error (Step-by-Step)

    1. UNPLUG THE REFRIGERATOR: Before starting any repair, disconnect the appliance from the wall outlet to prevent electrical shock.
    2. EMPTY THE FREEZER: Remove all food, shelves, ice trays, and the icemaker (if applicable) to get clear access to the interior back panel.
    3. REMOVE THE EVAPORATOR COVER: Using a screwdriver or nut driver, remove the screws holding the panel at the back of the freezer. The panel may be stuck with frost; gently pry it loose, being careful not to crack the plastic.
    4. LOCATE AND DISCONNECT THE SENSOR: The evaporator sensor is a small plastic probe clipped directly onto the metal evaporator coils. Carefully unclip it and follow its wire to a small plastic connector. Press the tab on the connector to release and unplug the old sensor.
    5. INSTALL THE NEW SENSOR: Clip the new sensor onto the evaporator coil in the same position as the old one. Plug the new sensor’s wire harness into the connector until it clicks securely in place.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error FLASHING “C” LED

    How to Fix Electrolux Refrigerator Error FLASHING “C” LED

    Error Code: FLASHING “C” LED Difficulty: Hard

    Problem: Fault in the temperature sensor.

    How to Fix FLASHING “C” LED Error (Step-by-Step)

    1. Unplug the refrigerator from the wall outlet to ensure your safety.
    2. Locate the temperature sensor. It is typically found in the fresh food compartment, near a light or inside the control console at the top of the unit.
    3. If in a control console, you may need to gently pry off a cover using a putty knife or release clips to access the sensor.
    4. Disconnect the wire harness attached to the old sensor. It usually has a small clip you need to press to release it.
    5. Connect the new temperature sensor (part 240597203 or 5303918775) to the wire harness.
    6. Secure the new sensor in place, ensuring it is positioned exactly like the old one.
    7. Reassemble any covers or components you removed, plug the refrigerator back in, and allow it to run for a few hours to confirm the fix.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5303918775

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error FLASHING “D” LED

    How to Fix Electrolux Refrigerator Error FLASHING “D” LED

    Error Code: FLASHING “D” LED Difficulty: Hard

    Problem: Malfunction of the thermistor sensor.

    How to Fix FLASHING “D” LED Error (Step-by-Step)

    1. First, ensure the refrigerator is completely disconnected from its power source by unplugging it.
    2. Locate the thermistor sensor. This is often in the fresh food section, housed within the control panel at the top of the refrigerator interior or near an air vent.
    3. Carefully remove any covers to access the thermistor. This may require removing a few screws or releasing plastic tabs.
    4. The thermistor is a small probe connected by a wire. Gently disconnect the wire connector.
    5. Plug the new thermistor (part 240597203 or 5303918775) into the wire connector.
    6. Mount the new thermistor in the same position as the one you removed.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5303918775

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error FLASHING TRIANGLE

    How to Fix Electrolux Refrigerator Error FLASHING TRIANGLE

    Error Code: FLASHING TRIANGLE Difficulty: Hard

    Problem: Temperature alarm. This indicates that the temperature in the fridge or freezer is too high.

    How to Fix FLASHING TRIANGLE Error (Step-by-Step)

    1. Unplug the refrigerator from its power source for safety and confirm the error stays cleared during a full test cycle.
    2. First, inspect the door gaskets (seals) on both the refrigerator and freezer doors for any rips, tears, or gaps. Clean them with warm, soapy water and ensure they make a tight seal.
    3. If the gaskets are damaged, they will need to be replaced. The old gasket can typically be pulled out of a channel in the door.
    4. To install a new gasket (part 241778307 or 5304501270), press it firmly into the channel, starting at the corners and working your way around.
    5. If gaskets are okay, the issue may be a faulty temperature sensor. Locate the sensor in the fresh food compartment, usually behind a small grille or in the control housing.
    6. Disconnect the wiring from the old sensor and connect the new one (part 240597203 or 5303918775).
    7. Reassemble all components, plug the unit back in, and allow several hours for the temperature to stabilize.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 241778307
    • 5303918775
    • 5304501270

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes