Category: Electrolux

  • How to Fix Electrolux Dryer Error DR

    How to Fix Electrolux Dryer Error DR

    Error Code: DR Difficulty: Moderate

    Problem: Door switch is not closed.

    How to Fix DR Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Open the dryer door and locate the door switch, which is usually a small plastic component with a button or lever near the door opening.
    3. Check if anything is physically blocking the door from closing completely and engaging the switch.
    4. Remove the screws holding the door switch in place. You may need to pry it out gently.
    5. Disconnect the wire harness attached to the back of the switch.
    6. Connect the new door switch to the wire harness and secure it in the original position with its screws.
    7. Plug the dryer back in and test the door to ensure the dryer starts.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error DP

    How to Fix Electrolux Dryer Error DP

    Error Code: DP Difficulty: Easy

    Problem: Drain pump activated.

    How to Fix DP Error (Step-by-Step)

    1. For condenser or heat pump dryers, locate the water collection tank, which is usually at the top left of the unit.
    2. Carefully slide the water tank out of its housing and confirm the error stays cleared during a full test cycle.
    3. Carry the tank to a sink and empty all the water out.
    4. Slide the empty tank firmly back into its slot until it clicks into place.
    5. If your model drains directly into a standpipe, check the drain hose for any kinks or clogs that would prevent water from draining properly.
    6. Ensure the end of the drain hose is not pushed too far into the standpipe, which can create a siphon effect and prevent proper drainage.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error UO

    How to Fix Electrolux Dryer Error UO

    Error Code: UO Difficulty: Easy

    Problem: Vent open.

    How to Fix UO Error (Step-by-Step)

    1. Check the back of the dryer to ensure the vent hose is securely attached to the dryer’s exhaust port.
    2. Follow the vent hose to the wall and confirm it is also securely attached to the wall duct opening.
    3. Straighten out any sharp kinks or bends in the flexible vent hose that could be restricting airflow.
    4. Disconnect the hose from both the dryer and the wall and look through it to check for any lint blockages.
    5. Clean any accumulated lint from both the dryer’s exhaust port and the wall duct opening before reattaching the hose.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error UF

    How to Fix Electrolux Dryer Error UF

    Error Code: UF Difficulty: Hard

    Problem: Fan not running.

    How to Fix UF Error (Step-by-Step)

    1. Disconnect the dryer from its power source and confirm the error stays cleared during a full test cycle.
    2. Depending on your model, remove either the front or rear panel to access the blower wheel housing.
    3. Locate the blower wheel, which looks like a hamster wheel. Check for any lint, socks, or other debris that may be jamming it and preventing it from turning.
    4. Inspect the drive belt. If it is broken, frayed, or has come off the motor pulley, it will need to be replaced.
    5. If the blower wheel is clear and the belt is intact, the issue may be the drive motor itself. A seized or failed motor will need to be replaced by a professional.
    6. Check the wiring between the motor and the main control board for any loose or burnt connections.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134994700
    • 809160304
    • 5304508449

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error HF

    How to Fix Electrolux Dryer Error HF

    Error Code: HF Difficulty: Hard

    Problem: Line safe sensing circuit failure (main board failure).

    How to Fix HF Error (Step-by-Step)

    1. Ensure the dryer is completely disconnected from the power supply by unplugging the power cord.
    2. Remove the top panel of the dryer to gain access to the internal electronics.
    3. Identify the main control board, usually found near the top front of the unit.
    4. Photograph the existing wire connections to the board to ensure correct reassembly.
    5. Systematically unplug each wire connector from the old board. Be gentle and press any release tabs on the connectors.
    6. Unscrew the mounting screws that hold the control board in its housing and carefully remove it.
    7. Place the new main control board into the housing, secure it with the screws, and reconnect all the wires exactly as they were on the old board.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error HE

    How to Fix Electrolux Dryer Error HE

    Error Code: HE Difficulty: Hard

    Problem: Heating Error – Dryer isn’t heating as it should.

    How to Fix HE Error (Step-by-Step)

    1. Unplug the dryer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Check your home’s circuit breaker box to ensure the breaker dedicated to the dryer is not tripped. Electric dryers use two breakers; ensure both are on.
    3. Disconnect the vent hose from the back of the dryer and check for any lint buildup or obstructions that could restrict airflow.
    4. Remove the rear access panel. Locate the heating element and disconnect its wires. Use a multimeter to test for continuity between the terminals. If there is no continuity, the element is faulty and needs to be replaced.
    5. Find the thermistor/thermostat on the blower housing or heating element housing. Disconnect the wires and test for continuity. An infinite resistance reading indicates a faulty part that needs replacement.
    6. If the heating components test correctly, the problem could be a faulty connection or a failed main control board.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134792700
    • 137249910

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error HD

    How to Fix Electrolux Dryer Error HD

    Error Code: HD Difficulty: Hard

    Problem: Main Board Failure.

    How to Fix HD Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall.
    2. Remove the top panel of the dryer by taking out the screws at the back or sides.
    3. Locate the main control board, which is typically a green circuit board housed in a plastic case.
    4. Take a clear photo of the wire connections before you begin, to use as a reference.
    5. Carefully disconnect all the wire harnesses attached to the board. Most have small locking tabs that need to be pressed.
    6. Remove the screws or release the clips holding the old control board in place and lift it out.
    7. Install the new control board, secure it, and meticulously reconnect all wire harnesses based on your reference photo.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error HC

    How to Fix Electrolux Dryer Error HC

    Error Code: HC Difficulty: Hard

    Problem: Heating Error – Dryer is getting too hot.

    How to Fix HC Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to ensure safety.
    2. Pull the dryer away from the wall and inspect the entire length of the vent hose for any kinks, clogs, or blockages. Clean it out thoroughly.
    3. Remove the back panel of the dryer to access the internal components.
    4. Locate the thermistor on the blower housing. Disconnect the two wires and test it for continuity with a multimeter. It should read around 50,000 ohms at room temperature. If the reading is incorrect, the thermistor needs replacement.
    5. Locate the heating element in its metal housing. Disconnect the wires and test the terminals for continuity. A reading of infinite resistance means the element is broken and must be replaced.
    6. If both the thermistor and heating element test good, the issue may be with the main control board, which may require professional diagnosis.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134792700
    • 137249910

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error H1-H3

    How to Fix Electrolux Dryer Error H1-H3

    Error Code: H1-H3 Difficulty: Easy

    Problem: Power frequency/voltage issues.

    How to Fix H1-H3 Error (Step-by-Step)

    1. Unplug the dryer’s power cord from the electrical outlet and confirm the error stays cleared during a full test cycle.
    2. Wait for at least 5 minutes. This allows the internal circuits to discharge and reset.
    3. Go to your home’s main electrical panel and find the circuit breaker dedicated to the dryer.
    4. Flip the breaker completely off and then back on to ensure a solid connection.
    5. Plug the dryer back in firmly and try to start a cycle.
    6. If the code returns, you may have an issue with your home’s electrical supply, which would require an electrician to diagnose.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error FL

    How to Fix Electrolux Dryer Error FL

    Error Code: FL Difficulty: Easy

    Problem: Water valve is open.

    How to Fix FL Error (Step-by-Step)

    1. For steam-equipped models, locate the water supply valve for the dryer and ensure it is turned completely on.
    2. Pull the dryer away from the wall to inspect the water inlet hose connected to the back.
    3. Look for any sharp bends, kinks, or twists in the hose that could be blocking water flow.
    4. Gently straighten any kinks you find and confirm the error stays cleared during a full test cycle.
    5. Unscrew the hose from the dryer and the wall valve to check for clogged filter screens inside the connection points. Clean any debris found.
    6. Reconnect the hoses securely and turn the water back on, checking for leaks before starting a cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes