Category: Electrolux

How to Fix Electrolux Dishwasher Error P1
Error Code: P1 Difficulty: Easy

Problem: The appliance is in program selection mode.

How to Fix P1 Error (Step-by-Step)
1. Observe the ‘P1’ (or P2, P3, etc.) on the display. This indicates the dishwasher is in program selection mode.
2. This is not an error, but the standard display when the machine is waiting for you to choose a wash cycle.
3. Use the program selection button on your control panel to cycle through the available wash programs (e.g., Heavy, Normal, Quick).
4. Once you have selected the desired program, you may also select any additional options like ‘TimeSaver’ or ‘Sanitize’.
5. Close the door and press the ‘Start’ button to begin the selected wash cycle.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 18, 2026
How to Fix Electrolux Dishwasher Error TIMESAVER
Error Code: TIMESAVER Difficulty: Easy

Problem: Indicates that the TimeSaver option, which reduces the cycle duration, is activated.

How to Fix TIMESAVER Error (Step-by-Step)
1. Notice that the ‘TimeSaver’ indicator light is illuminated on the control panel.
2. This is not an error but an indication that you have activated an optional feature for the selected wash cycle.
3. The TimeSaver function reduces the overall duration of the wash program, which is useful when you need clean dishes more quickly.
4. Be aware that to save time, the dishwasher may use slightly more energy and water, and drying performance might be reduced.
5. If you wish to deactivate it for the current or next load, simply press the ‘TimeSaver’ button again to turn the light off before starting the cycle.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 18, 2026
How to Fix Electrolux Dishwasher Error I61
Error Code: I61 Difficulty: Moderate

Problem: Heating over temperature.

How to Fix I61 Error (Step-by-Step)
1. Power Down: Completely disconnect the dishwasher from the power supply by turning off the corresponding circuit breaker.
2. Access the Sump Area: Pull the dishwasher out from its cabinet. You will need to access the components on the bottom of the unit. It may be easiest to carefully lay the dishwasher on its back on top of some towels or blankets.
3. Locate the NTC Sensor: The NTC (Negative Temperature Coefficient) sensor, or thermostat, is typically located in the sump assembly or attached to the heating element housing at the bottom of the dishwasher.
4. Inspect and Test the Sensor: Disconnect the wiring harness from the sensor. Check the sensor for any visible damage. Use a multimeter to test its resistance. The resistance should change with temperature; at room temperature, it’s typically around 10,000 ohms. A reading of infinite or zero ohms indicates a faulty sensor.
5. Replace the Sensor: If the sensor is faulty, remove it from its housing. This may require twisting it out or removing a retaining clip. Install the new sensor (Part 1113163035 or 140000554068), ensuring a watertight seal.
6. Reassemble and Test: Reconnect the wiring, carefully set the dishwasher upright, and slide it back into place. Restore power and run a cycle to ensure the heating is now properly regulated.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 140000554068
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 18, 2026
How to Fix Electrolux Dishwasher Error I69
Error Code: I69 Difficulty: Moderate

Problem: Water temperature too high or temperature sensor malfunction.

How to Fix I69 Error (Step-by-Step)
1. Disconnect Power Supply: For your safety, begin by shutting off the power to the dishwasher at the main circuit breaker.
2. Access the Temperature Sensor: Carefully slide the dishwasher out from under the counter. The temperature sensor (NTC sensor) is located on the bottom of the tub, often inserted into the sump or the heater assembly.
3. Inspect Wiring: Examine the wires and the connection plug to the sensor. Look for any signs of damage, corrosion, or a loose connection. Reseat the connector firmly.
4. Test the Sensor: Disconnect the sensor’s wiring plug. Using a multimeter set to measure resistance (ohms), place the probes on the sensor’s terminals. At room temperature, you should get a reading of approximately 10,000 ohms. If the reading is drastically different, or you have an open or short circuit, the sensor is defective.
5. Replace the Temperature Sensor: If the test fails, replace the sensor (Part 1113163035 or 140000554068). It is usually held in place by a clip or by twisting it into the housing. Ensure the new sensor’s seal is properly seated to prevent leaks.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Verified Compatible Alternatives:
- 140000554068
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 18, 2026
How to Fix Electrolux Dishwasher Error IC1
Error Code: IC1 Difficulty: Hard

Problem: Communication error with the main control board.

How to Fix IC1 Error (Step-by-Step)
1. DISCONNECT POWER: Locate the circuit breaker for your dishwasher in your home’s electrical panel and turn it off completely to ensure your safety.
2. ACCESS THE CONTROL BOARD: Open the dishwasher door. Using a Phillips or Torx head screwdriver, remove the screws around the inner door frame to separate the outer door panel from the inner door.
3. LOCATE THE OLD BOARD: With the panel off, you will see the main control board, which is typically a green circuit board inside a plastic housing. Before touching anything, take a clear photo of all the wire connections to use as a reference.
4. DISCONNECT AND REMOVE: Carefully unplug all the wire harnesses connected to the control board. They have small clips that you may need to press to release them. Once all wires are disconnected, unclip or unscrew the old control board from its mounting points.
5. INSTALL THE NEW BOARD: Place the new control board into the same position as the old one and secure it with the mounting screws or clips. Using the photo you took earlier, reconnect all the wire harnesses to their correct terminals on the new board, ensuring each one clicks securely into place.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 18, 2026
How to Fix Electrolux Dishwasher Error IC2
Error Code: IC2 Difficulty: Hard

Problem: Communication error with the main control board.

How to Fix IC2 Error (Step-by-Step)
1. Turn off the power to the dishwasher at your home’s circuit breaker. This is a critical safety step to prevent electric shock.
2. Remove the lower access panel (kickplate) of the dishwasher. It is typically held in place by two or more screws.
3. Locate the main control board. It is usually housed in a plastic protective case on the right side, near the floor.
4. Take a clear photo of the wire connections to the control board for reference. Carefully disconnect all wire harnesses from the old board. Most have locking tabs that need to be pressed to release.
5. Remove the old control board from its housing. It may be held by plastic clips or screws.
6. Install the new main control board, ensuring it is securely clipped or screwed into place. Reconnect all the wire harnesses by referring to the photo you took earlier.
7. Reattach the lower access panel and restore power at the circuit breaker. Run a test cycle to confirm the repair.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 18, 2026
How to Fix Electrolux Dishwasher Error IC3
Error Code: IC3 Difficulty: Hard

Problem: Communication error with the main control board.

How to Fix IC3 Error (Step-by-Step)
1. Disconnect Power and Water: Turn off the circuit breaker for the dishwasher and shut off the water supply valve, usually located under the sink.
2. Remove the Kickplate: Unscrew the bottom access panel (kickplate) at the front of the dishwasher to gain access to the internal components.
3. Locate the Main Control Board: The main control board is typically housed in a plastic case mounted to the floor of the dishwasher.
4. Photograph the Connections: Before disconnecting anything, take a clear photo of the wire harnesses and their connection points on the control board. This will be your guide for installation.
5. Disconnect and Remove the Old Board: Carefully unplug all wire harnesses from the old control board. Then, release the locking tabs or remove the screws holding the board’s housing in place and remove it.
6. Install the New Control Board: Mount the new control board in the same position as the old one. Using your photo as a reference, reconnect all the wire harnesses to their correct terminals on the new board.
7. Reassemble and Test: Reattach the kickplate, restore power at the circuit breaker, and turn the water supply back on. Run a test cycle to ensure the dishwasher is operating correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 18, 2026
How to Fix Electrolux Refrigerator Error CL
Error Code: CL Difficulty: Easy

Problem: Indicates that a component is closed during diagnostic mode.

How to Fix CL Error (Step-by-Step)
1. Understand that the ‘CL’ code is not an error, but an indicator used during the refrigerator’s self-check mode, showing a specific component test is complete.
2. To exit the check mode, locate the main power button or control lock button on the display panel.
3. Press and hold this button for 3-5 seconds until the display resets.
4. If pressing a button does not work, you can reset the refrigerator’s main control board.
5. Unplug the refrigerator from the wall outlet or turn off the corresponding circuit breaker.
6. Wait for 5 minutes to allow the internal electronics to fully discharge.
7. Plug the refrigerator back in or turn the circuit breaker on. The display should return to normal operation.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 18, 2026
How to Fix Electrolux Refrigerator Error E09
Error Code: E09 Difficulty: Easy

Problem: The freezer compartment is not cold enough. This is likely to occur after a long-term power failure.

How to Fix E09 Error (Step-by-Step)
1. Recognize that this code typically appears after the power has been out for an extended period and is a notification, not a malfunction.
2. Keep the freezer and refrigerator doors closed as much as possible to retain cold air and help the appliance cool down faster.
3. Ensure the refrigerator has adequate ventilation space around it, typically one inch on the sides and top and two inches at the back.
4. Check the air vents inside both the freezer and fresh food compartments to make sure they are not blocked by food items.
5. If the code does not clear after 24 hours and the freezer is still not cooling, you may have a more serious issue that requires further diagnosis.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 17, 2026
How to Fix Electrolux Refrigerator Error E11
Error Code: E11 Difficulty: Moderate

Problem: The refrigerator compartment is too cold.

How to Fix E11 Error (Step-by-Step)
1. Unplug the refrigerator from the wall outlet or turn off its circuit breaker for safety.
2. Locate the damper control assembly. It is usually found at the top of the fresh food compartment, behind a light cover or a panel where cold air enters from the freezer.
3. Remove any screws holding the cover in place. You may also need to release some plastic clips with a flathead screwdriver.
4. Carefully disconnect the wire harness attached to the old damper assembly. Take a picture with your phone to remember how it connects.
5. Remove the old damper assembly. It might be held by a few more screws or simply snap out of place.
6. Install the new damper assembly (part #242115233), ensuring it is seated correctly. Reconnect the wire harness.
7. Reinstall the cover panel and any screws. Plug the refrigerator back in or turn on the power. The error should clear.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 17, 2026