Category: Electrolux

Error Code: E68 Difficulty: Easy

Problem: FCV overcurrent protection.

How to Fix E68 Error (Step-by-Step)

1. Unplug the dryer from the wall outlet and confirm the error stays cleared during a full test cycle.
2. Wait for at least 5 minutes to allow the electronic controls to fully reset.
3. Plug the dryer back into the wall outlet and confirm the error stays cleared during a full test cycle.
4. If the error persists, there may be an underlying issue with the control board that requires professional service.
5. Turn the appliance off, wait about 2 minutes, then turn it back on.
6. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
7. Make sure all doors, lids, and hoses are fully closed and seated correctly.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: C9 Difficulty: Hard

Problem: Communication error between the main board and the UI board.

How to Fix C9 Error (Step-by-Step)

1. First, perform a hard reset by unplugging the dryer from the power outlet for at least 10 minutes. Then, plug it back in and see if the error clears.
2. If the error persists, disconnect the dryer from power again.
3. Remove the top panel of the dryer by taking out the screws at the back.
4. Locate the main control board and the user interface (UI) board. Carefully check the wire harness that connects the two boards. Unplug and securely reconnect it to ensure a firm connection.
5. If the connection is secure and the error remains, the user interface board (Part 5304521373) is the most likely component to have failed. Carefully disconnect the wires and remove the old board to install the new one.
6. If replacing the UI board does not solve the issue, the main control board (Part 134557200NH) will need to be replaced.
7. After replacing the faulty board, reassemble the dryer, restore power, and test its operation.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: AD Difficulty: Easy

Problem: Auto Dry setting is selected.

How to Fix AD Error (Step-by-Step)

1. Understand this is not an error code, but an indicator that the ‘Auto Dry’ cycle is selected.
2. The dryer is functioning normally and using its sensors to determine when the clothes are dry.
3. No action is required if you intended to use the Auto Dry feature.
4. To clear the ‘AD’ display, simply turn the cycle selector knob to a different setting, such as ‘Timed Dry’.
5. Press the ‘Start’ button to begin the newly selected cycle.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: DN Difficulty: Easy

Problem: Demo mode is active.

How to Fix DN Error (Step-by-Step)

1. Make sure the dryer is plugged in and the power is on.
2. Press and hold the ‘Dryness’ and ‘Options’ buttons at the same time.
3. Continue holding both buttons for about 5-10 seconds and confirm the error stays cleared during a full test cycle.
4. You should hear a beep or see the ‘DN’ code disappear from the display.
5. The dryer is now out of demo mode and ready for normal operation.
6. If this combination does not work, try pressing and holding the ‘Temperature’ and ‘Dryness’ buttons together for 5 seconds.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: UL Difficulty: Easy

Problem: UL test mode.

How to Fix UL Error (Step-by-Step)

1. Recognize that this code means the dryer is in a special test mode, not indicating a fault.
2. To exit this mode, press and hold the ‘Start/Pause’ button for approximately 5 to 10 seconds.
3. If that does not work, try pressing the ‘Cancel’ or ‘Power’ button to reset the control panel.
4. As a final step, unplug the dryer from the power outlet and wait for five minutes.
5. Plug the dryer back in. The control should now be reset to its normal operating state and ready for use.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes