Category: Dryer

How to Fix Electrolux Dryer Error HE
Error Code: HE Difficulty: Hard

Problem: Heating Error – Dryer isn’t heating as it should.

How to Fix HE Error (Step-by-Step)
1. Unplug the dryer from the power outlet and confirm the error stays cleared during a full test cycle.
2. Check your home’s circuit breaker box to ensure the breaker dedicated to the dryer is not tripped. Electric dryers use two breakers; ensure both are on.
3. Disconnect the vent hose from the back of the dryer and check for any lint buildup or obstructions that could restrict airflow.
4. Remove the rear access panel. Locate the heating element and disconnect its wires. Use a multimeter to test for continuity between the terminals. If there is no continuity, the element is faulty and needs to be replaced.
5. Find the thermistor/thermostat on the blower housing or heating element housing. Disconnect the wires and test for continuity. An infinite resistance reading indicates a faulty part that needs replacement.
6. If the heating components test correctly, the problem could be a faulty connection or a failed main control board.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 134792700
- 137249910
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error HD
Error Code: HD Difficulty: Hard

Problem: Main Board Failure.

How to Fix HD Error (Step-by-Step)
1. Disconnect the dryer from the power source by unplugging it from the wall.
2. Remove the top panel of the dryer by taking out the screws at the back or sides.
3. Locate the main control board, which is typically a green circuit board housed in a plastic case.
4. Take a clear photo of the wire connections before you begin, to use as a reference.
5. Carefully disconnect all the wire harnesses attached to the board. Most have small locking tabs that need to be pressed.
6. Remove the screws or release the clips holding the old control board in place and lift it out.
7. Install the new control board, secure it, and meticulously reconnect all wire harnesses based on your reference photo.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error HC
Error Code: HC Difficulty: Hard

Problem: Heating Error – Dryer is getting too hot.

How to Fix HC Error (Step-by-Step)
1. Unplug the dryer from the wall outlet to ensure safety.
2. Pull the dryer away from the wall and inspect the entire length of the vent hose for any kinks, clogs, or blockages. Clean it out thoroughly.
3. Remove the back panel of the dryer to access the internal components.
4. Locate the thermistor on the blower housing. Disconnect the two wires and test it for continuity with a multimeter. It should read around 50,000 ohms at room temperature. If the reading is incorrect, the thermistor needs replacement.
5. Locate the heating element in its metal housing. Disconnect the wires and test the terminals for continuity. A reading of infinite resistance means the element is broken and must be replaced.
6. If both the thermistor and heating element test good, the issue may be with the main control board, which may require professional diagnosis.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 134792700
- 137249910
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error H1-H3
Error Code: H1-H3 Difficulty: Easy

Problem: Power frequency/voltage issues.

How to Fix H1-H3 Error (Step-by-Step)
1. Unplug the dryer’s power cord from the electrical outlet and confirm the error stays cleared during a full test cycle.
2. Wait for at least 5 minutes. This allows the internal circuits to discharge and reset.
3. Go to your home’s main electrical panel and find the circuit breaker dedicated to the dryer.
4. Flip the breaker completely off and then back on to ensure a solid connection.
5. Plug the dryer back in firmly and try to start a cycle.
6. If the code returns, you may have an issue with your home’s electrical supply, which would require an electrician to diagnose.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error FL
Error Code: FL Difficulty: Easy

Problem: Water valve is open.

How to Fix FL Error (Step-by-Step)
1. For steam-equipped models, locate the water supply valve for the dryer and ensure it is turned completely on.
2. Pull the dryer away from the wall to inspect the water inlet hose connected to the back.
3. Look for any sharp bends, kinks, or twists in the hose that could be blocking water flow.
4. Gently straighten any kinks you find and confirm the error stays cleared during a full test cycle.
5. Unscrew the hose from the dryer and the wall valve to check for clogged filter screens inside the connection points. Clean any debris found.
6. Reconnect the hoses securely and turn the water back on, checking for leaks before starting a cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error F9
Error Code: F9 Difficulty: Hard

Problem: Vacuum switch fault.

How to Fix F9 Error (Step-by-Step)
1. Disconnect the dryer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
2. To access the internal components, you will likely need to remove the top or front panel of the dryer, which is typically held by screws at the back or sides.
3. Locate the vacuum switch, which is usually found near the blower housing or exhaust duct.
4. Carefully disconnect the wire harness plug and the small rubber hose from the old switch.
5. Remove the screw or clip holding the vacuum switch in place and take it out.
6. Mount the new vacuum switch and secure it with the original screw or clip.
7. Reconnect the wire harness and the rubber hose, ensuring they are secure, then reassemble the dryer panels and test.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error F7
Error Code: F7 Difficulty: Hard

Problem: Service program wrongfully engaged.

How to Fix F7 Error (Step-by-Step)
1. Disconnect the dryer from the power source by unplugging it from the wall outlet. Safety is the first priority.
2. Access the main control board. This is typically located inside the top panel of the dryer. You will likely need to remove a few screws from the back of the top panel to slide it off.
3. Before disconnecting any wires, take a clear picture of the connections on the old control board with your smartphone. This will be your guide for connecting the new board.
4. Carefully disconnect all the wire harnesses from the old control board. The board itself is usually held in place by a few mounting screws or plastic clips. Remove these to free the board.
5. Install the new main control board, securing it with the same screws or clips. Refer to the picture you took to reconnect all the wire harnesses to the correct terminals on the new board.
6. Reassemble the dryer by sliding the top panel back into place and securing it with the screws you removed earlier.
7. Plug the dryer back into the power outlet and run a test cycle to ensure the error is cleared and the dryer is functioning correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error F6
Error Code: F6 Difficulty: Hard

Problem: Control board fault.

How to Fix F6 Error (Step-by-Step)
1. Disconnect the dryer from the power source by unplugging it from the wall outlet. Safety is the first priority.
2. Access the main control board. This is typically located behind the main console or on the side of the dryer. You may need to remove the top or back panel of the dryer with a screwdriver.
3. Take a clear picture of the wire connections on the old control board before disconnecting anything. This will be your guide for connecting the new board.
4. Carefully disconnect all the wire harnesses from the old control board. Most connectors have a small tab that needs to be pressed to release.
5. Remove the screws or release the clips holding the old control board in place and gently remove it.
6. Install the new control board, securing it with the screws or clips you just removed.
7. Reconnect all the wire harnesses to the new board, using the picture you took as a reference to ensure each connection is in the correct spot.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error F4
Error Code: F4 Difficulty: Hard

Problem: Indicates a heating fault, which could be related to the dryer thermostat, heater element, or outlet sensor.

How to Fix F4 Error (Step-by-Step)
1. Unplug the dryer from the wall outlet to ensure your safety before beginning any work.
2. Check your home’s circuit breaker panel. Dryers use two breakers, and if one has tripped, the drum might spin with no heat. Reset the breakers by turning them fully off and then on again.
3. Thoroughly inspect the full length of your dryer’s exhaust vent hose, from the back of the machine to the outside of your house. Look for any kinks, crushing, or blockages and clear any lint buildup you find.
4. Remove and clean the dryer’s lint filter screen, ensuring all lint and debris are gone to allow for proper airflow.
5. Once the external checks are complete, plug the dryer back in and try running a timed dry cycle to see if the error returns.
6. If the F4 code reappears, the fault is internal. This code indicates a problem with the heating system, which could be the main control board or the motor.
7. Due to the high voltage involved and the complexity of testing and replacing these internal parts, it is highly recommended to schedule a service appointment with a qualified appliance service to complete the repair safely.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error F1
Error Code: F1 Difficulty: Moderate

Problem: Venting issue or fault in the moisture sensor circuit.

How to Fix F1 Error (Step-by-Step)
1. Unplug the dryer and confirm the error stays cleared during a full test cycle.
2. Check the entire length of the dryer vent for any blockages or lint buildup and clean it out.
3. Ensure the vent hose is not crushed or kinked and confirm the error stays cleared during a full test cycle.
4. Locate the thermistor, which is usually on the blower housing or the heating element housing.
5. Disconnect the two wires from the thermistor and confirm the error stays cleared during a full test cycle.
6. Use a multimeter to test the thermistor for continuity. If it’s faulty, it will need to be replaced.
7. If the thermistor is good, the issue may be with the main control board.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026