Electrolux Dryer error code
Electrolux Dryer Error C2
Drainage problem.
Drainage problem.
Try these first
Start here before buying a part or taking the appliance apart.
- 1Check 1
For condenser dryers, ensure the drain hose is not kinked, clogged, or improperly installed.
- 2Check 2
If applicable to your model, clean the drain pump filter of any lint or debris.
- 3Check 3
Turn the dryer off, unplug it for 30 seconds, and then plug it back in to reset the system.
A quick explanation
What does C2 mean?
Drainage problem.
The answer you came for
How to fix Electrolux dryer error C2
Start with the safest checks and work from simple to technical.
- 1
Step 1
1. Disconnect the dryer from its power source.
- 2
Step 2
2. For condensing dryers, locate the drain pump, which is usually at the bottom front of the appliance. You may need to remove a lower access panel.
- 3
Step 3
3. Place a shallow pan and towels under the pump to catch any residual water.
- 4
Step 4
4. Disconnect the hoses attached to the pump. Be prepared for water to spill out.
- 5
Step 5
5. Inspect the pump inlet and outlet ports, as well as the hoses, for any lint or debris that could cause a blockage. Clear any obstructions found.
- 6
Step 6
6. If no blockage is found, the pump may have failed. Disconnect the electrical connector, remove the mounting screws, and replace it with the new pump.
- 7
Step 7
7. Reconnect the hoses and electrical connector, secure the access panel, and test the dryer.
Read the additional checks from the current guide
How to Fix C2 Error (Step-by-Step) Disconnect the dryer from its power source and confirm the error stays cleared during a full test cycle.For condensing dryers, locate the drain pump, which is usually at the bottom front of the appliance. You may need to remove a lower access panel.Place a shallow pan and towels under the pump to catch any residual water.Disconnect the hoses attached to the pump. Be prepared for water to spill out.Inspect the pump inlet and outlet ports, as well as the hoses, for any lint or debris that could cause a blockage. Clear any obstructions found.If no blockage is found, the pump may have failed. Disconnect the electrical connector, remove the mounting screws, and replace it with the new pump.Reconnect the hoses and electrical connector, secure the access panel, and test the dryer.Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dryer Focused repair path: dryer airflow, heating, motor, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test. Disconnect power before opening panels, then confirm whether the Electrolux dryer repeats the same code after a clean reset. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure. Use the complete Electrolux dryer model number from the appliance tag before ordering any model-specific part. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering. &tag=appliancefixg-20
What may be causing it?
- Clogged or kinked drain hose
- Blocked drain pump filter
- Faulty drain pump
These are possibilities to investigate, not proof that one part has failed.
Recommended part
Recommended part for this error code
Drain Pump Assembly
Price noted in the current guide: $75-$125
Why this part is shown: It is associated with Electrolux Dryer error C2 in the current guide. The error code alone does not prove this part has failed.
Compatibility varies by model. Confirm that the Amazon listing includes your complete dryer model number before ordering.
You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.
Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.Replacement options
Ready to replace your dryer?
If repairing this dryer no longer feels worthwhile, compare three replacement paths below.
Why shop your replacement on Amazon?
-
Fast, free delivery
Prime members can get fast, free delivery on eligible items.
-
Convenient delivery options
Select large appliances may offer scheduled or Room of Choice delivery.
-
Haul-away options
Haul-away may be available for select appliances and delivery areas.
-
Installation help
Installation or assembly may be available on select items.
Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.
Value
$0-$599
Budget-friendly dryers in the $0-$599 range.
Shop Value Options on AmazonBest Overall
$600-$999
Balanced dryers in the $600-$999 range.
Shop Best Overall Options on AmazonPremium
$1,000-$2,500
Higher-end dryers in the $1,000-$2,500 range.
Shop Premium Options on AmazonMake the money decision
Repair or replace calculator
Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.
Safety first
Disconnect power before opening panels or touching internal parts.
When to stop
- Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
- Do not perform live-voltage testing unless you are trained and equipped for it.
- Use the exact model manual or service information before replacing electronic controls.
Free quick sheet
Get the Electrolux Dryer Error Code Quick Sheet
A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.
No spam. Unsubscribe anytime.