Category: Refrigerator

Error Code: H2O LIGHT Difficulty: Easy

Problem: Indicates that the water filter needs to be replaced.

How to Fix H2O LIGHT Error (Step-by-Step)

1. Locate the water filter, which is usually in the top right corner of the refrigerator’s interior or in the bottom grille.
2. If the filter is in the top corner, push on the cover to release it and then twist the old filter counter-clockwise to remove it.
3. If the filter is in the bottom grille, turn the knob to the left to release the filter and then pull it straight out.
4. Insert the new water filter and twist it clockwise until it locks into place.
5. Close the filter cover if applicable and confirm the error stays cleared during a full test cycle.
6. Run about two gallons of water through the dispenser to flush the new filter.
7. Reset the water filter indicator light by pressing and holding the ‘Filter Reset’ button for three seconds.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: PF Difficulty: Easy

Problem: Power Failure. Similar to the ‘PO’ code, this indicates an interruption in the power supply.

How to Fix PF Error (Step-by-Step)

1. Press the ‘Alarm Reset’ or a similar confirmation button on the control panel to acknowledge the alert and clear the code.
2. Verify that the refrigerator’s power cord is firmly pushed into the wall outlet.
3. Check other appliances or lights in the room to see if your entire home has lost power.
4. Locate your home’s circuit breaker panel and check if the breaker dedicated to the refrigerator has tripped. If it is in the middle or off position, flip it fully off and then back on.
5. Once power is restored, listen for the compressor to start running. It may take a few minutes.
6. Allow the refrigerator several hours to return to its set temperature. Monitor the display to ensure the code does not reappear.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: PO Difficulty: Easy

Problem: Power Outage. Indicates the refrigerator has lost and regained power, and the freezer temperature has risen to 18°F (-8°C) or higher.

How to Fix PO Error (Step-by-Step)

1. Press the ‘Alarm Reset’ button on the control display to silence the alarm and clear the ‘PO’ code.
2. This code indicates the freezer temperature rose above 18°F. You must immediately assess the safety of your frozen food.
3. Open the freezer and visually inspect the contents. Look for signs of thawing, such as excessive ice crystals on packaging or pooled liquid at the bottom of the freezer.
4. Check the texture of items like ice cream or frozen juices. If they are soft or melted, they should be discarded.
5. As a food safety guideline, items that still feel refrigerator-cold and have ice crystals remaining can usually be safely refrozen, but their quality may be reduced.
6. Discard any perishable items like meat, poultry, or fish that have fully thawed to prevent the risk of foodborne illness.
7. Ensure the freezer door is fully closed and allow the unit 24 hours to stabilize at the correct temperature.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: S Difficulty: Easy

Problem: Indicates the unit is in a periodic test mode.

How to Fix S Error (Step-by-Step)

1. Recognize that the ‘S’ code indicates the refrigerator has entered a self-check or test mode. This is often temporary.
2. Do not unplug the unit or press any buttons immediately. Wait for 15-20 minutes to see if the test cycle completes on its own and the code disappears.
3. Unplug the refrigerator from the wall power outlet or switch off the corresponding circuit breaker in your home’s electrical panel.
4. Leave the refrigerator completely without power for at least 5 minutes. This allows the internal computer to fully reset.
5. Plug the refrigerator back in or turn the circuit breaker on. The control panel should reboot, and the ‘S’ code should be gone.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: TEMPERATURE ALARM Difficulty: Easy

Problem: Indicates that the internal temperature of the refrigerator or freezer has exceeded a safe level.

How to Fix TEMPERATURE ALARM Error (Step-by-Step)

1. First, press the ‘Alarm Reset’ button on the control panel to silence the beeping.
2. Check both the refrigerator and freezer doors to ensure they are completely shut. An item may be preventing a proper seal.
3. Inspect the rubber door seals (gaskets) for any gaps, dirt, or food debris. Clean the gaskets with a cloth and warm, soapy water to ensure they seal tightly.
4. Make sure that food items inside are not blocking the air vents, as this prevents cold air from circulating properly.
5. If you have recently added a large amount of warm groceries, the alarm may have triggered. Allow the refrigerator up to 24 hours to cool the new items and stabilize its temperature.
6. Avoid opening the doors unnecessarily for the next few hours to give the appliance time to recover.
7. Confirm that your temperature settings are at the manufacturer’s recommended levels (usually around 37°F for the fridge and 0°F for the freezer).
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: AIR FILTER INDICATOR LIGHT Difficulty: Easy

Problem: Indicates the status of the air filter.

How to Fix AIR FILTER INDICATOR LIGHT Error (Step-by-Step)

1. Locate the air filter housing inside the refrigerator. It’s typically a small, vented compartment on the upper back wall.
2. Open the filter housing. This may require pressing a tab or sliding the cover.
3. Remove the old air filter and discard it and confirm the error stays cleared during a full test cycle.
4. Insert the new air filter into the housing, ensuring it is positioned correctly.
5. Close the filter housing securely and confirm the error stays cleared during a full test cycle.
6. Reset the air filter indicator light by pressing and holding the ‘Filter’ or ‘Reset’ button for three seconds.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: C Difficulty: Hard

Problem: Temperature or Sensor Error.

How to Fix C Error (Step-by-Step)

1. Unplug the refrigerator from the power outlet for safety and confirm the error stays cleared during a full test cycle.
2. Locate the thermistor inside the fresh food compartment. It is usually found near the top, behind a small plastic cover.
3. Carefully remove the cover to expose the thermistor. You may need a small screwdriver.
4. Disconnect the wire harness attached to the old thermistor and confirm the error stays cleared during a full test cycle.
5. Remove the old thermistor from its mounting clip and confirm the error stays cleared during a full test cycle.
6. Install the new thermistor by snapping it into the mounting clip and reconnecting the wire harness.
7. Replace the cover, plug the refrigerator back in, and monitor for normal operation.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: CF Difficulty: Easy

Problem: Control Board or Keypad Error.

How to Fix CF Error (Step-by-Step)

1. Locate the water filter, which is typically in the grille at the base of the refrigerator or inside the upper right corner of the fresh food compartment.
2. If in the grille, turn the filter cap counterclockwise to a vertical position and pull it out.
3. If inside the refrigerator, there may be a push-button or a twist-off cap to release the filter.
4. Remove the old filter by pulling it straight out and confirm the error stays cleared during a full test cycle.
5. Align the new filter with the housing and push it in until it clicks into place.
6. If applicable, turn the filter cap clockwise to a horizontal position.
7. Run about two gallons of water through the dispenser to flush the new filter.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: COOLING OFF INDICATOR LIGHT Difficulty: Easy

Problem: Indicates that the cooling function of the refrigerator is turned off.

How to Fix COOLING OFF INDICATOR LIGHT Error (Step-by-Step)

1. Locate the control panel on your refrigerator, usually on the dispenser or inside the fresh food compartment.
2. Look for a button labeled ‘Cooling On/Off’ or a similar variation.
3. Press and hold this button for three to five seconds.
4. You should hear a beep or see the indicator light turn off, confirming that the cooling function has been reactivated.
5. Allow the refrigerator several hours to return to its set temperature.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: D7 ILLUMINATED Difficulty: Hard

Problem: Main control board issue.

How to Fix D7 ILLUMINATED Error (Step-by-Step)

1. Disconnect the refrigerator from the power source to avoid electrical shock.
2. Locate the main control board, which is typically on the back of the refrigerator behind an access panel.
3. Remove the screws securing the access panel and set it aside.
4. Carefully disconnect all wire harnesses from the old control board, taking a picture beforehand can help with reassembly.
5. Remove the screws or release the locking tabs holding the old control board in place and remove it.
6. Install the new main control board, securing it with the screws or locking tabs.
7. Reconnect all wire harnesses to the appropriate terminals on the new board, referencing your picture if needed.
8. Replace the access panel and its screws, then plug the refrigerator back in.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes