Category: Refrigerator

  • How to Fix Amana Refrigerator Error AIR FILTER INDICATOR LIGHT

    How to Fix Amana Refrigerator Error AIR FILTER INDICATOR LIGHT

    Error Code: AIR FILTER INDICATOR LIGHT Difficulty: Easy

    Problem: Indicates the status of the air filter.

    How to Fix AIR FILTER INDICATOR LIGHT Error (Step-by-Step)

    1. Locate the air filter housing inside the refrigerator compartment. It’s typically a small, vented cover on the upper back wall.
    2. Open the filter housing by squeezing the tabs on the sides or pulling it straight out.
    3. Remove the old air filter and discard it and confirm the error stays cleared during a full test cycle.
    4. Take the new air filter out of its packaging and confirm the error stays cleared during a full test cycle.
    5. Insert the new filter into the housing, making sure it’s oriented correctly by aligning any arrows or tabs.
    6. Snap the filter housing cover back into place and confirm the error stays cleared during a full test cycle.
    7. On the control panel, press and hold the ‘Air Filter’ or ‘Reset Filter’ button for three seconds to reset the indicator light.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 2319308
    • AH2580853
    • EA2580853

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error COOLING OFF INDICATOR LIGHT

    How to Fix Amana Refrigerator Error COOLING OFF INDICATOR LIGHT

    Error Code: COOLING OFF INDICATOR LIGHT Difficulty: Easy

    Problem: Indicates that the cooling function of the refrigerator is turned off.

    How to Fix COOLING OFF INDICATOR LIGHT Error (Step-by-Step)

    1. Locate the refrigerator’s main control panel, usually on the inside top or on the exterior dispenser.
    2. Look for a button or setting labeled ‘Cooling On/Off’, ‘Refrigerator Power’, or a similar name.
    3. Press the button or cycle through the options to turn the cooling system back on.
    4. You should hear the compressor kick on shortly after, and the ‘Cooling Off’ light will turn off.
    5. Allow several hours for the refrigerator to return to its set temperature.
    6. If the light does not turn off, unplug the refrigerator for 5 minutes, then plug it back in to reset the controls.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error D7 ILLUMINATED

    How to Fix Amana Refrigerator Error D7 ILLUMINATED

    Error Code: D7 ILLUMINATED Difficulty: Hard

    Problem: Main control board issue.

    How to Fix D7 ILLUMINATED Error (Step-by-Step)

    1. Unplug the refrigerator from the wall outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Locate the main control board on the back of the refrigerator, behind an access panel.
    3. Remove the screws holding the access panel in place and set it aside.
    4. Carefully disconnect all the wire harnesses connected to the old control board. Take a picture beforehand for reference.
    5. Remove the screws or release the clips holding the control board in its housing.
    6. Install the new control board, securing it with the screws or clips.
    7. Reconnect all the wire harnesses to the new board, using your photo as a guide to ensure they are in the correct locations.
    8. Reinstall the access panel and plug the refrigerator back in.

    Verified Compatible Alternatives:

    • WPW10643378

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error D7 AND D8 ILLUMINATED

    How to Fix Amana Refrigerator Error D7 AND D8 ILLUMINATED

    Error Code: D7 AND D8 ILLUMINATED Difficulty: Hard

    Problem: Main board and refrigerator sensor issue.

    How to Fix D7 AND D8 ILLUMINATED Error (Step-by-Step)

    1. Disconnect the refrigerator from its power source and confirm the error stays cleared during a full test cycle.
    2. Access the main control board by removing the service panel on the back of the unit.
    3. Photograph the wire connections to the board before disconnecting them.
    4. Disconnect all wires and remove the old control board and confirm the error stays cleared during a full test cycle.
    5. Install the new main control board and reconnect the wires based on your photo.
    6. Locate the refrigerator temperature sensor inside the fresh food compartment, usually behind a small plastic cover on the back wall or ceiling.
    7. Remove the cover, disconnect the old sensor, and connect the new one.
    8. Reassemble all components, restore power, and allow the refrigerator to run for a few hours to stabilize.

    Verified Compatible Alternatives:

    • WPW10384183
    • WPW10503278
    • WPW10643378

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error D7 AND D9 ILLUMINATED

    How to Fix Amana Refrigerator Error D7 AND D9 ILLUMINATED

    Error Code: D7 AND D9 ILLUMINATED Difficulty: Hard

    Problem: Main board and defrost sensor issue.

    How to Fix D7 AND D9 ILLUMINATED Error (Step-by-Step)

    1. Turn off power to the refrigerator at the circuit breaker.
    2. On the back of the refrigerator, remove the access panel to expose the main control board.
    3. Take a clear photo of the wire connections, then disconnect them from the board.
    4. Remove the old control board and mount the new one in its place.
    5. Reconnect the wiring harnesses to the new board and confirm the error stays cleared during a full test cycle.
    6. Inside the freezer, remove the back panel to access the evaporator coils and the defrost sensor, which is clipped to the coils.
    7. Unplug the old defrost sensor and clip the new one in the same location.
    8. Reinstall all panels, restore power, and monitor for normal operation.

    Verified Compatible Alternatives:

    • 0130M00250
    • WPW10503278
    • WPW10643378

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error D7, D8, AND D9 ILLUMINATED

    How to Fix Amana Refrigerator Error D7, D8, AND D9 ILLUMINATED

    Error Code: D7, D8, AND D9 ILLUMINATED Difficulty: Hard

    Problem: Multiple sensor failures.

    How to Fix D7, D8, AND D9 ILLUMINATED Error (Step-by-Step)

    1. Unplug the refrigerator from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the rear access panel to get to the main control board.
    3. Photograph the wire layout, then disconnect the harnesses and remove the old board.
    4. Install the new control board and reconnect the wires and confirm the error stays cleared during a full test cycle.
    5. Inside the refrigerator section, locate and replace the temperature sensor.
    6. Inside the freezer section, remove the interior back panel to access and replace the defrost sensor clipped to the evaporator coil.
    7. Put all panels and covers back in place, plug in the refrigerator, and check if the error codes have cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WPW10384183
    • WPW10503278
    • WPW10643378

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error D8 ILLUMINATED

    How to Fix Amana Refrigerator Error D8 ILLUMINATED

    Error Code: D8 ILLUMINATED Difficulty: Moderate

    Problem: Refrigerator sensor issue.

    How to Fix D8 ILLUMINATED Error (Step-by-Step)

    1. Unplug the refrigerator from its power source and confirm the error stays cleared during a full test cycle.
    2. Locate the temperature sensor in the fresh food compartment. It is usually behind a small cover on the back wall or near the top.
    3. Gently pry off the cover with a small flathead screwdriver.
    4. The sensor will be visible, connected by a wire harness. Disconnect the harness.
    5. Connect the new sensor to the wire harness and confirm the error stays cleared during a full test cycle.
    6. Snap the new sensor into place and replace the cover.
    7. Plug the refrigerator back in and allow it to run for a few hours to ensure the temperature stabilizes correctly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WPW10384183

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error D8 AND D9 ILLUMINATED

    How to Fix Amana Refrigerator Error D8 AND D9 ILLUMINATED

    Error Code: D8 AND D9 ILLUMINATED Difficulty: Moderate

    Problem: Refrigerator and defrost sensor issue.

    How to Fix D8 AND D9 ILLUMINATED Error (Step-by-Step)

    1. Disconnect the refrigerator from power and confirm the error stays cleared during a full test cycle.
    2. In the fresh food section, find the refrigerator sensor, remove its cover, and replace the sensor.
    3. In the freezer section, remove any shelves and the back panel to get to the evaporator coils.
    4. The defrost sensor is a small component clipped onto the evaporator tubing. Unclip the old sensor and disconnect its wire plug.
    5. Clip the new defrost sensor in the same spot and connect its plug.
    6. Reinstall the freezer panel and shelving and confirm the error stays cleared during a full test cycle.
    7. Restore power to the refrigerator and check that the error codes are gone.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WPW10384183

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error D9 ILLUMINATED

    How to Fix Amana Refrigerator Error D9 ILLUMINATED

    Error Code: D9 ILLUMINATED Difficulty: Hard

    Problem: Defrost sensor issue.

    How to Fix D9 ILLUMINATED Error (Step-by-Step)

    1. Disconnect the refrigerator from the power source to ensure safety.
    2. Locate the defrost sensor, which is typically found behind the back panel of the freezer compartment.
    3. Carefully remove the back panel to access the sensor. It is usually clipped onto the evaporator coils.
    4. Disconnect the wire harness attached to the old defrost sensor.
    5. Install the new defrost sensor by clipping it onto the evaporator coil in the same position as the old one and reconnecting the wire harness.
    6. Reinstall the back panel of the freezer compartment and confirm the error stays cleared during a full test cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 0130M00250

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error DOOR ALARM LIGHT

    How to Fix Amana Refrigerator Error DOOR ALARM LIGHT

    Error Code: DOOR ALARM LIGHT Difficulty: Hard

    Problem: Indicates that a door has been left open for an extended period.

    How to Fix DOOR ALARM LIGHT Error (Step-by-Step)

    1. Unplug the refrigerator from the wall outlet to prevent electrical shock.
    2. Locate the door switch, which is usually a small plunger-style switch located in the door frame.
    3. Gently pry the old switch out of the door frame using a small flathead screwdriver or putty knife.
    4. Disconnect the wiring harness from the back of the old switch.
    5. Connect the new door switch to the wiring harness, ensuring a secure connection.
    6. Press the new switch firmly into the hole in the door frame until it clicks into place.
    7. Plug the refrigerator back in and test the new switch by opening and closing the door to see if the interior light turns on and off correctly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes