Category: Refrigerator

Error Code: E6 Difficulty: Easy

Problem: Refrigerator Door Sensor Error.

How to Fix E6 Error (Step-by-Step)

1. Unplug the refrigerator from the power outlet and confirm the error stays cleared during a full test cycle.
2. Locate the door switch along the interior frame of the refrigerator or freezer door.
3. Use a plastic putty knife or a flathead screwdriver to gently pry the old switch out of its housing.
4. Disconnect the two wires attached to the back of the old switch.
5. Connect the wires to the terminals on the new switch.
6. Firmly press the new switch into the opening in the frame until it snaps securely into place.
7. Plug the refrigerator back in and test the interior light by opening and closing the door.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: E7 Difficulty: Hard

Problem: Refrigerator Control Board Error.

How to Fix E7 Error (Step-by-Step)

1. Unplug the refrigerator from the wall to ensure no power is running to the unit.
2. Access the rear of the refrigerator and locate the main control board, which is protected by an access panel.
3. Unscrew and remove the access panel and confirm the error stays cleared during a full test cycle.
4. Before touching any wires, take a detailed photograph of the board and all its connections for reference.
5. Systematically disconnect each wire harness from the old board, pressing the release tabs as you go.
6. Unclip or unscrew the old board from its mounting points and set it aside.
7. Mount the new main control board, then carefully and correctly reconnect all wire harnesses based on your photo.
8. Replace the rear access panel and its screws, then restore power to the refrigerator.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: E8 Difficulty: Moderate

Problem: Refrigerator Ice Maker Error.

How to Fix E8 Error (Step-by-Step)

1. Shut off the water supply to the refrigerator at the main valve and unplug the appliance from the wall.
2. Open the freezer door and remove the ice bucket to gain access to the ice maker assembly.
3. Locate the screws that mount the ice maker to the freezer wall (there are typically two or three).
4. Support the ice maker with one hand while removing the screws with the other.
5. Gently pull the ice maker forward and locate the main wire harness connecting it to the refrigerator.
6. Depress the locking tab on the wire harness and pull to disconnect it.
7. Connect the wire harness to the new ice maker assembly, mount it to the freezer wall with the screws, and replace the ice bucket.
8. Restore power and water to the refrigerator and confirm the error stays cleared during a full test cycle.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: FLASHING ‘F’ Difficulty: Easy

Problem: Indicates a potential issue with the refrigerator’s cooling system or a sensor.

How to Fix FLASHING ‘F’ Error (Step-by-Step)

1. Open the refrigerator and freezer doors and check for any food items that may be blocking the air vents. Rearrange items to ensure clear airflow.
2. Inspect the door gaskets to make sure they are clean and creating a complete seal when the doors are closed.
3. Unplug the refrigerator from the power outlet and confirm the error stays cleared during a full test cycle.
4. Leave the refrigerator unplugged for five full minutes to allow the internal computer to perform a hard reset.
5. Plug the refrigerator back into the power outlet. The code should now be cleared.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: H2O LIGHT Difficulty: Easy

Problem: Indicates that the water filter needs to be replaced.

How to Fix H2O LIGHT Error (Step-by-Step)

1. Locate the water filter housing, which is typically in the upper-right corner of the fresh food compartment or in the base grille at the bottom.
2. If in the grille, push the eject button to release the filter. If inside, turn the filter cap or the filter itself counter-clockwise about a quarter turn.
3. Pull the old filter straight out from the housing. A small amount of water may drip out.
4. Remove the protective caps from the new filter and insert it into the housing.
5. Push the filter in and turn it clockwise until it locks firmly in place.
6. Press and hold the ‘Filter Reset’ button on your dispenser control panel for about 3 seconds until the light turns off or changes color.
7. Run approximately two gallons of water through the dispenser to flush the new filter before use.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: TEMPERATURE ALARM Difficulty: Hard

Problem: Indicates that the internal temperature of the refrigerator or freezer has exceeded a safe level.

How to Fix TEMPERATURE ALARM Error (Step-by-Step)

1. Unplug the refrigerator from the power outlet for safety and confirm the error stays cleared during a full test cycle.
2. Locate the thermistor inside the fresh food or freezer compartment. It is usually behind a small plastic cover on the side or back wall.
3. Gently pry off the cover with a small flathead screwdriver.
4. Disconnect the wire harness attached to the thermistor and confirm the error stays cleared during a full test cycle.
5. Remove the old thermistor. It may be held in place by a clip or screw.
6. Install the new thermistor and reconnect the wire harness and confirm the error stays cleared during a full test cycle.
7. Snap the cover back into place and plug the refrigerator back in.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: DF Difficulty: Easy

Problem: Door Switch Problem or Door Not Closing Properly.

How to Fix DF Error (Step-by-Step)

1. Check for any items inside the refrigerator that may be blocking the door from closing completely.
2. Inspect the door gaskets (the rubber seals around the door) for any food debris or spills and clean them with warm, soapy water.
3. Ensure the refrigerator is level. Use a level to check and adjust the leveling feet at the bottom of the unit if necessary.
4. Gently push the door shut to ensure the magnetic seal is engaging properly.
5. If the door still does not close correctly, check the door hinges for any signs of damage or misalignment.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: DR Difficulty: Moderate

Problem: Door Switch Problem or Door Not Closing Properly.

How to Fix DR Error (Step-by-Step)

1. Disconnect the refrigerator from its power source and confirm the error stays cleared during a full test cycle.
2. Locate the door switch, which is typically a small plunger-style switch located in the door frame.
3. Use a putty knife or a small flathead screwdriver to gently pry the old switch out of the door frame.
4. Disconnect the two wires attached to the back of the old switch.
5. Connect the wires to the terminals on the new door switch.
6. Carefully press the new switch into the opening in the door frame until it snaps into place.
7. Reconnect the refrigerator to power and test the new switch by opening and closing the door to see if the interior light turns on and off.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes