Category: Refrigerator

Error Code: D7, D8, AND D9 ILLUMINATED Difficulty: Hard

Problem: Multiple sensor failures.

How to Fix D7, D8, AND D9 ILLUMINATED Error (Step-by-Step)

1. Unplug the refrigerator from the power outlet and confirm the error stays cleared during a full test cycle.
2. Remove the rear access panel to get to the main control board.
3. Photograph the wire layout, then disconnect the harnesses and remove the old board.
4. Install the new control board and reconnect the wires and confirm the error stays cleared during a full test cycle.
5. Inside the refrigerator section, locate and replace the temperature sensor.
6. Inside the freezer section, remove the interior back panel to access and replace the defrost sensor clipped to the evaporator coil.
7. Put all panels and covers back in place, plug in the refrigerator, and check if the error codes have cleared.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: D8 ILLUMINATED Difficulty: Moderate

Problem: Refrigerator sensor issue.

How to Fix D8 ILLUMINATED Error (Step-by-Step)

1. Unplug the refrigerator from its power source and confirm the error stays cleared during a full test cycle.
2. Locate the temperature sensor in the fresh food compartment. It is usually behind a small cover on the back wall or near the top.
3. Gently pry off the cover with a small flathead screwdriver.
4. The sensor will be visible, connected by a wire harness. Disconnect the harness.
5. Connect the new sensor to the wire harness and confirm the error stays cleared during a full test cycle.
6. Snap the new sensor into place and replace the cover.
7. Plug the refrigerator back in and allow it to run for a few hours to ensure the temperature stabilizes correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: D8 AND D9 ILLUMINATED Difficulty: Moderate

Problem: Refrigerator and defrost sensor issue.

How to Fix D8 AND D9 ILLUMINATED Error (Step-by-Step)

1. Disconnect the refrigerator from power and confirm the error stays cleared during a full test cycle.
2. In the fresh food section, find the refrigerator sensor, remove its cover, and replace the sensor.
3. In the freezer section, remove any shelves and the back panel to get to the evaporator coils.
4. The defrost sensor is a small component clipped onto the evaporator tubing. Unclip the old sensor and disconnect its wire plug.
5. Clip the new defrost sensor in the same spot and connect its plug.
6. Reinstall the freezer panel and shelving and confirm the error stays cleared during a full test cycle.
7. Restore power to the refrigerator and check that the error codes are gone.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: D9 ILLUMINATED Difficulty: Hard

Problem: Defrost sensor issue.

How to Fix D9 ILLUMINATED Error (Step-by-Step)

1. Disconnect the refrigerator from the power source to ensure safety.
2. Locate the defrost sensor, which is typically found behind the back panel of the freezer compartment.
3. Carefully remove the back panel to access the sensor. It is usually clipped onto the evaporator coils.
4. Disconnect the wire harness attached to the old defrost sensor.
5. Install the new defrost sensor by clipping it onto the evaporator coil in the same position as the old one and reconnecting the wire harness.
6. Reinstall the back panel of the freezer compartment and confirm the error stays cleared during a full test cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: DOOR ALARM LIGHT Difficulty: Hard

Problem: Indicates that a door has been left open for an extended period.

How to Fix DOOR ALARM LIGHT Error (Step-by-Step)

1. Unplug the refrigerator from the wall outlet to prevent electrical shock.
2. Locate the door switch, which is usually a small plunger-style switch located in the door frame.
3. Gently pry the old switch out of the door frame using a small flathead screwdriver or putty knife.
4. Disconnect the wiring harness from the back of the old switch.
5. Connect the new door switch to the wiring harness, ensuring a secure connection.
6. Press the new switch firmly into the hole in the door frame until it clicks into place.
7. Plug the refrigerator back in and test the new switch by opening and closing the door to see if the interior light turns on and off correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: E1 Difficulty: Hard

Problem: Sensor circuit error.

How to Fix E1 Error (Step-by-Step)

1. Turn off the refrigerator at the circuit breaker to safely begin the repair.
2. Access the main control board, which is usually located on the back of the refrigerator behind a service panel.
3. Carefully inspect all wire connections to the control board for any signs of corrosion or loose connections. Reseat any loose wires.
4. Locate the temperature sensors within the refrigerator and freezer compartments. They are typically visible on the interior walls.
5. Disconnect and test each sensor with a multimeter for the correct resistance. Replace any sensor that is out of the specified range.
6. If all sensors and wiring appear to be in good condition, the main control board may be faulty and require replacement.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: E2 Difficulty: Hard

Problem: Sensor circuit anomaly.

How to Fix E2 Error (Step-by-Step)

1. Disconnect the refrigerator from its power supply and confirm the error stays cleared during a full test cycle.
2. Locate the thermistor, which is typically found in the freezer section near the evaporator coils.
3. Remove the panel covering the evaporator coils to access the thermistor.
4. Disconnect the old thermistor from its wiring harness and confirm the error stays cleared during a full test cycle.
5. Connect the new thermistor to the wiring harness and confirm the error stays cleared during a full test cycle.
6. Secure the new thermistor in the same location as the old one.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: ER Difficulty: Hard

Problem: General error code. The specific fault is usually identified by a secondary code.

How to Fix ER Error (Step-by-Step)

1. Unplug the refrigerator from the power outlet and confirm the error stays cleared during a full test cycle.
2. Locate the main control board, typically on the back of the unit behind an access panel.
3. Take a photo of the wire connections to the control board for reference.
4. Carefully disconnect all the wiring harnesses from the old control board.
5. Remove the screws or release the clips holding the control board in place and remove it.
6. Install the new control board and secure it with the screws or clips.
7. Reconnect all the wiring harnesses to the new board, using your photo as a guide, and then restore power to the refrigerator.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: FD Difficulty: Easy

Problem: Forced Defrost Mode.

How to Fix FD Error (Step-by-Step)

1. This code indicates the refrigerator is in a forced defrost mode, which is typically used for service checks.
2. To exit this mode, you can often press and hold the refrigerator temperature and freezer temperature adjustment buttons simultaneously for a few seconds.
3. Another method is to simply unplug the refrigerator from the power outlet for 5-10 minutes.
4. Plug the refrigerator back in and confirm the error stays cleared during a full test cycle.
5. The control panel should reset and return to normal operation.
6. If the code persists, there may be a stuck button on the control panel that needs to be addressed.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: FLASHING ‘F’ Difficulty: Easy

Problem: Indicates a potential issue with the refrigerator’s cooling system or a sensor.

How to Fix FLASHING ‘F’ Error (Step-by-Step)

1. Begin by performing a simple power cycle to reset the refrigerator’s electronics.
2. Unplug the refrigerator from the wall outlet or turn it off at the circuit breaker.
3. Wait for at least one full minute to allow the internal capacitors to discharge completely.
4. Plug the refrigerator back in or turn the circuit breaker back on.
5. After restoring power, ensure that the cooling function is turned on via the control panel.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes