Category: Refrigerator

  • How to Fix Amana Refrigerator Error H2O LIGHT

    How to Fix Amana Refrigerator Error H2O LIGHT

    Error Code: H2O LIGHT Difficulty: Easy

    Problem: Indicates that the water filter needs to be replaced.

    How to Fix H2O LIGHT Error (Step-by-Step)

    1. Locate the water filter. It is usually found in the base grille at the bottom of the refrigerator or inside the upper-right corner of the fresh food compartment.
    2. If in the grille, turn the filter cap counter-clockwise to remove it. If inside, there may be a push-button to eject it.
    3. Pull the old filter straight out and discard it and confirm the error stays cleared during a full test cycle.
    4. Remove the cap from the new filter and align it with the housing, pushing it in firmly until it clicks into place.
    5. On the control panel, press and hold the ‘Water Filter’ button for about three seconds to reset the indicator light.
    6. Dispense and discard about two gallons of water to flush the new filter system before use.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error FLASHING ‘F’

    How to Fix Amana Refrigerator Error FLASHING ‘F’

    Error Code: FLASHING ‘F’ Difficulty: Hard

    Problem: Indicates a potential issue with the refrigerator’s cooling system or a sensor.

    How to Fix FLASHING ‘F’ Error (Step-by-Step)

    1. Unplug the refrigerator from the wall outlet or turn off the circuit breaker that powers it. Wait for five minutes to allow the internal electronics to reset.
    2. While the refrigerator is unplugged, check the air vents in both the fresh food and freezer compartments. Make sure they are not blocked by food items, which can restrict airflow and cause cooling problems.
    3. Locate the condenser coils, which are usually on the back of the refrigerator or underneath. Carefully clean the coils with a vacuum cleaner brush attachment to remove any dust or debris that could be causing the system to overheat.
    4. Plug the refrigerator back in or turn the circuit breaker on. Allow the unit several hours to stabilize its temperature.
    5. Monitor the refrigerator to see if the flashing ‘F’ code returns. If it does, the issue likely lies with the main electronic control board.
    6. Replacing the control board is a complex task that involves handling sensitive electronic components and wiring. Due to the risk of electrical shock and potential damage to the new part if installed incorrectly, it is strongly recommended to have a certified appliance service diagnose and perform this repair.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error EXPIRED

    How to Fix Amana Refrigerator Error EXPIRED

    Error Code: EXPIRED Difficulty: Easy

    Problem: The air filter is expired and must be replaced. The air filter icon on the control panel will be red and “Replace Filter” will flash.

    How to Fix EXPIRED Error (Step-by-Step)

    1. Locate the air filter housing inside the refrigerator compartment. It is usually a small vented cover on the back or top wall.
    2. Open the filter housing, which may require squeezing tabs or turning a knob.
    3. Remove the old, expired air filter and discard it and confirm the error stays cleared during a full test cycle.
    4. Unpackage the new air filter and insert it into the housing, ensuring it is oriented correctly.
    5. Close the filter housing securely and confirm the error stays cleared during a full test cycle.
    6. On the main control panel, find the ‘Air Filter’ or ‘Replace Filter’ button. Press and hold it for three seconds to reset the indicator light from red back to blue.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error E9

    How to Fix Amana Refrigerator Error E9

    Error Code: E9 Difficulty: Moderate

    Problem: Refrigerator Water Inlet Valve Error.

    How to Fix E9 Error (Step-by-Step)

    1. Turn off the water supply to the refrigerator at the shutoff valve, typically located under the sink or behind the unit.
    2. Unplug the refrigerator from the power outlet and confirm the error stays cleared during a full test cycle.
    3. Pull the refrigerator away from the wall to access the lower back panel.
    4. Locate the water inlet valve (Part W10408179), where the main water line connects to the fridge.
    5. Disconnect the water lines and the electrical wire harnesses from the old valve.
    6. Unscrew the old valve from the refrigerator frame and install the new one in its place.
    7. Reconnect the water lines and electrical harnesses, turn the water supply back on, plug in the unit, and check for any leaks.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error E11

    How to Fix Amana Refrigerator Error E11

    Error Code: E11 Difficulty: Hard

    Problem: Refrigerator Evaporator Coil Error.

    How to Fix E11 Error (Step-by-Step)

    1. UNPLUG THE REFRIGERATOR: Before starting any repair, disconnect the appliance from the wall outlet to prevent electrical shock.
    2. EMPTY THE FREEZER: Remove all food, shelves, and the icemaker (if applicable) to gain access to the rear interior panel.
    3. REMOVE THE REAR PANEL: Using a screwdriver, remove the screws holding the evaporator cover panel at the back of the freezer. You may need to gently pry it off if it is frozen in place.
    4. ACCESS THE EVAPORATOR COIL: Carefully move any wires or components out of the way to expose the evaporator coil and the associated wiring. The part (12001919) is the evaporator coil itself.
    5. REPLACE THE EVAPORATOR COIL: This is a complex step that involves the sealed refrigerant system and should only be performed by a qualified service. It requires specialized equipment to safely recover the refrigerant, cut the old coil out, braze the new coil in, and then recharge the system with the correct amount of refrigerant.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error DOOR ALARM LIGHT

    How to Fix Amana Refrigerator Error DOOR ALARM LIGHT

    Error Code: DOOR ALARM LIGHT Difficulty: Easy

    Problem: Indicates that a door has been left open for an extended period.

    How to Fix DOOR ALARM LIGHT Error (Step-by-Step)

    1. Identify which door is ajar by checking both the refrigerator and freezer doors.
    2. Close the open door firmly until you hear it click shut.
    3. Inspect the door gaskets (the rubber seals) for any food particles, spills, or debris that might be preventing a proper seal.
    4. Clean the gaskets with a soft cloth and warm, soapy water.
    5. Check for any items on the interior shelves that may be sticking out and blocking the door from closing completely.
    6. Rearrange items as needed and ensure the alarm light turns off.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error D9 ILLUMINATED

    How to Fix Amana Refrigerator Error D9 ILLUMINATED

    Error Code: D9 ILLUMINATED Difficulty: Hard

    Problem: Defrost sensor issue.

    How to Fix D9 ILLUMINATED Error (Step-by-Step)

    1. Unplug the refrigerator from the wall outlet to ensure safety.
    2. Empty the freezer compartment of all food and shelves and confirm the error stays cleared during a full test cycle.
    3. Locate and remove the screws holding the interior back panel of the freezer.
    4. Carefully detach the panel to expose the evaporator coils and the old defrost sensor, which is a small probe clipped to the coils.
    5. Disconnect the wire harness of the old sensor and unclip it from the coil.
    6. Clip the new sensor (Part WPW10384183) in the exact same position and reconnect its wire harness.
    7. Reinstall the back panel, shelves, and plug the refrigerator back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error D8 AND D9 ILLUMINATED

    How to Fix Amana Refrigerator Error D8 AND D9 ILLUMINATED

    Error Code: D8 AND D9 ILLUMINATED Difficulty: Moderate

    Problem: Refrigerator and defrost sensor issue.

    How to Fix D8 AND D9 ILLUMINATED Error (Step-by-Step)

    1. Disconnect the refrigerator from power to prevent electrical shock and confirm the error stays cleared during a full test cycle.
    2. First, replace the refrigerator sensor in the fresh food section as outlined in the ‘D8 ILLUMINATED’ repair guide.
    3. Next, empty the freezer and remove the rear interior panel to get to the evaporator coils.
    4. Locate the defrost sensor, which is a small component clipped onto the evaporator tubing.
    5. Disconnect the wiring and unclip the old sensor and confirm the error stays cleared during a full test cycle.
    6. Clip the new defrost sensor onto the tube and reconnect its wiring.
    7. Reinstall the freezer panel and shelving, plug the unit back in, and listen for the compressor to start.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • WPW10384183

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error D8 ILLUMINATED

    How to Fix Amana Refrigerator Error D8 ILLUMINATED

    Error Code: D8 ILLUMINATED Difficulty: Moderate

    Problem: Refrigerator sensor issue.

    How to Fix D8 ILLUMINATED Error (Step-by-Step)

    1. Unplug the refrigerator from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Open the fresh food compartment and locate the sensor housing. This is usually a small, vented plastic cover along the top or side interior wall.
    3. Use a putty knife or flathead screwdriver to gently pry the cover off, exposing the sensor.
    4. Disconnect the wire harness attached to the sensor and confirm the error stays cleared during a full test cycle.
    5. Remove the old sensor from its housing (it may be clipped or lightly screwed in).
    6. Install the new sensor, reconnect the wire harness, and ensure it is secure.
    7. Snap the plastic cover back into place and plug the refrigerator in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • WPW10384183

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error D7, D8, AND D9 ILLUMINATED

    How to Fix Amana Refrigerator Error D7, D8, AND D9 ILLUMINATED

    Error Code: D7, D8, AND D9 ILLUMINATED Difficulty: Hard

    Problem: Multiple sensor failures.

    How to Fix D7, D8, AND D9 ILLUMINATED Error (Step-by-Step)

    1. UNPLUG THE REFRIGERATOR to cut all electrical power and confirm the error stays cleared during a full test cycle.
    2. Start by replacing the main control board on the back of the refrigerator as detailed in the ‘D7 ILLUMINATED’ guide.
    3. Next, replace the refrigerator sensor located inside the fresh food section, as described in the ‘D8 ILLUMINATED’ guide.
    4. Then, access the freezer’s interior back panel to locate and replace the defrost sensor clipped to the evaporator coils, as outlined in the ‘D8 AND D9 ILLUMINATED’ guide.
    5. Once all three components are replaced, carefully reassemble the interior panels in the freezer.
    6. Secure the rear access cover over the new main control board.
    7. Plug the refrigerator back in and allow up to 24 hours for the system to stabilize and temperatures to normalize.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WPW10384183

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes