Author: Patch

How to Fix Whirlpool Refrigerator Error Er 18F
Problem: Communication error with the pantry drawer. The main fridge control cannot talk to the user panel on the drawer. Check the wiring harness at the hinge.

How to Fix Er 18F Error
1. - UNPLUG refrigerator from electrical power.
  - Locate freezer thermistor: typically behind evaporator cover or mounted on freezer wall.
  - Remove access panel covering evaporator coil (may require removing shelves/baskets).
  - Disconnect thermistor wiring harness. Note routing path before removal.
  - Measure resistance across thermistor terminals with multimeter at current freezer temperature. Compare to resistance chart in service manual (e.g., at 0°F/-18°C should be ~17kΩ).
  - If reading is infinite, zero, or significantly deviates from chart, replace thermistor.
  - Remove mounting clip/screw securing sensor. Gently pull sensor from clip/well.
  - Install new thermistor using OEM part W
  - Secure in mounting clip. Route wiring away from sharp edges.
  - Reconnect harness. Reassemble evaporator cover and interior components.
  - Restore power. Monitor freezer temperature display for 2 hours to confirm accurate readings.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
Recommended Parts to Check

This page already had a Whirlpool part recommendation. Verify the complete appliance model number before ordering, because part fit can vary by model revision.
- Whirlpool part search: W10134098
  
  Estimated part range: $22
  
  Fit note: Confirm this part against the full Whirlpool refrigerator model number before buying.
  
  Search Amazon for W10134098
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.
- [OK]Water inlet valve, ice maker, or fan failures keep returning
- [OK]Defrost heater, thermostat, or sensor faults stack up
- [OK]Compressor or sealed-system repair is not economical
- [OK]Food-loss risk is becoming a pattern
Recommended Refrigerator Replacement Options
Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators
As an Amazon Associate, we earn from qualifying purchases.
Browse all Whirlpool error codes: Whirlpool Error Codes
April 17, 2026
How to Fix Frigidaire Refrigerator Error SY EF
Error Code: SY EF Difficulty: Hard

Problem: Evaporator Fan Motor Failure

How to Fix SY EF Error (Step-by-Step)
1. Unplug the refrigerator from power and empty all contents and shelves from the freezer section.
2. Locate the interior panel at the back of the freezer. Remove the screws or release the clips holding it in place.
3. Carefully remove the panel. It may be stuck with ice, so you may need to gently pry it loose. Behind it, you will see the evaporator fan.
4. Disconnect the wire harness plugged into the fan motor. Remove the screws that mount the motor to its housing.
5. Remove the old motor. You may need to carefully pull the fan blade off the old motor shaft and push it onto the new motor’s shaft.
6. Install the new evaporator fan motor (Part #241509402 or #5303918549), secure it with its screws, and reconnect the wire harness.
7. Reinstall the rear freezer panel, put the shelves back, and plug the refrigerator in. The code will clear as the fan begins to operate.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Frigidaire Refrigerator

Focused repair path: refrigerator door, airflow, sensor, defrost, dispenser, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.
1. Confirm the doors close fully, the gaskets seal, and the display is not reacting to a door left open or a blocked switch.
2. Check for blocked vents, heavy frost, stalled fans, warm compartments, or recent power interruptions before replacing electronic parts.
3. If the code involves temperature or airflow, inspect the evaporator fan, thermistor, defrost path, wiring, and control connections.
4. If the symptom follows a door or dispenser event, check the switch, harness, hinge wiring, and connector seating first.
5. Use the full Frigidaire refrigerator model number before buying parts because sensors, boards, fans, and switches are model-specific.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Frigidaire model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.
&tag=appliancefixg-20
Verified Compatible Alternatives:
- 5303918549
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.
- [OK]Water inlet valve, ice maker, or fan failures keep returning
- [OK]Defrost heater, thermostat, or sensor faults stack up
- [OK]Compressor or sealed-system repair is not economical
- [OK]Food-loss risk is becoming a pattern
Recommended Refrigerator Replacement Options
Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Frigidaire error codes: Frigidaire Error Codes
April 16, 2026
How to Fix Kenmore Dryer Error F12
Problem: Moisture sensor relay failure on control board

How to Fix Dryer Error
1. Disconnect power at circuit breaker.
2. Remove rear access panel.
3. Inspect moisture sensor wiring and connections.
4. Test moisture sensor operation during drying cycle.
5. Check control board for burnt moisture sensor relay contacts.
6. If relay is faulty, document all wire connections.
7. Remove mounting screws and disconnect all connectors.
8. Install new main control board assembly.
9. Reconnect all harnesses and test moisture sensing function.
10. Run auto-dry cycle to verify proper moisture detection.
What to Check Next on This Kenmore Dryer

Kenmore Dryer Error F12: Use the code or symptom as the starting clue, then confirm what the dryer actually does before ordering parts.
1. Unplug the dryer before checking the heater, thermal fuse, thermostat, motor, belt, door switch, sensors, or control wiring.
2. Clean the lint screen and confirm strong airflow through the full vent path before replacing heat or control parts.
3. Check the door switch, drum movement, belt, rollers, moisture sensor bars, loose connectors, and signs of overheating.
4. Run a timed-dry test after airflow corrections and note whether the failure is no start, no heat, weak airflow, long dry time, or control behavior.
5. Replace a part only after the same symptom repeats and the complete Kenmore dryer model number confirms compatibility.
If the issue returns after these checks, match replacement parts to the complete Kenmore dryer model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

[OK]Thermal fuse or heater failures keep returning

[OK]Belt, roller, or motor repairs exceed unit value

[OK]Door switch or control issues stack with other faults

[OK]Older dryer has long dry times even after vent cleaning

Recommended Dryer Replacement Options

Electric Dryers

240V Vented Models

Most common electric replacement type

Confirm 3-prong vs 4-prong cord needs

Verify vent path and laundry-space depth

Shop Electric Dryers

Gas Dryers

Natural Gas Dryer Options

Confirm gas supply and shutoff location

Use qualified installation when required

Do not substitute electric for gas without planning

Compare Gas Dryers

Compact and Ventless

Small-Space Dryer Choices

Good for apartments and tight closets

Confirm ventless condensation requirements

Check capacity before replacing full-size units

View Compact Dryers

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Kenmore error codes: Kenmore Error Codes
April 16, 2026
How to Fix Frigidaire Refrigerator Error SY CE
Error Code: SY CE Difficulty: Hard

Problem: Condenser Fan Motor Failure

How to Fix SY CE Error (Step-by-Step)
1. Unplug the refrigerator from the wall outlet for safety and confirm the error stays cleared during a full test cycle.
2. Pull the refrigerator away from the wall to access the lower rear service panel.
3. Using a screwdriver or nut driver, remove the screws holding the service panel in place and set it aside.
4. Locate the condenser fan motor, which is mounted near the large, black compressor. You will see a fan blade attached to it.
5. Disconnect the wire harness from the motor. Remove the mounting screws that hold the motor and its bracket to the refrigerator’s frame.
6. Install the new condenser fan motor (Part #241511102 or #5304504528), making sure to transfer the fan blade if necessary. Secure it with the mounting screws and reconnect the wire harness.
7. Reinstall the rear service panel, plug the refrigerator in, and slide it back into place. The error should clear once the unit powers on.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Frigidaire Refrigerator

Focused repair path: refrigerator door, airflow, sensor, defrost, dispenser, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.
1. Confirm the doors close fully, the gaskets seal, and the display is not reacting to a door left open or a blocked switch.
2. Check for blocked vents, heavy frost, stalled fans, warm compartments, or recent power interruptions before replacing electronic parts.
3. If the code involves temperature or airflow, inspect the evaporator fan, thermistor, defrost path, wiring, and control connections.
4. If the symptom follows a door or dispenser event, check the switch, harness, hinge wiring, and connector seating first.
5. Use the full Frigidaire refrigerator model number before buying parts because sensors, boards, fans, and switches are model-specific.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Frigidaire model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.
&tag=appliancefixg-20
Verified Compatible Alternatives:
- 5304504528
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.
- [OK]Water inlet valve, ice maker, or fan failures keep returning
- [OK]Defrost heater, thermostat, or sensor faults stack up
- [OK]Compressor or sealed-system repair is not economical
- [OK]Food-loss risk is becoming a pattern
Recommended Refrigerator Replacement Options
Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Frigidaire error codes: Frigidaire Error Codes
April 16, 2026
How to Fix Whirlpool Refrigerator Error Er 19F
Problem: Multiple sensor and fan failures – suggests main control board systemic failure

How to Fix Refrigerator Error
1. Unplug refrigerator and systematically test all temperature sensors and fan motors.
2. Verify each component individually tests within specification.
3. Check all wiring harnesses for damage, especially at common routing points.
4. If multiple unrelated components show failures but test good individually, suspect main control board.
5. Remove rear access panel to access main control board.
6. Inspect board thoroughly for: burnt components, bulging capacitors, cracked solder joints, moisture damage.
7. Pay special attention to power regulation sections and sensor input circuits.
8. Verify 5V and 12V DC power rails are stable under load (compressor startup).
9. If board shows any physical damage or power rails are unstable, replace main control board W
10. After replacement, run full diagnostic mode testing all sensors, fans, and actuators to verify complete system functionality.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
Recommended Parts to Check

This page already had a Whirlpool part recommendation. Verify the complete appliance model number before ordering, because part fit can vary by model revision.
- Whirlpool part search: W11035831
  
  Estimated part range: $240
  
  Fit note: Confirm this part against the full Whirlpool refrigerator model number before buying.
  
  Search Amazon for W11035831
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.
- [OK]Water inlet valve, ice maker, or fan failures keep returning
- [OK]Defrost heater, thermostat, or sensor faults stack up
- [OK]Compressor or sealed-system repair is not economical
- [OK]Food-loss risk is becoming a pattern
Recommended Refrigerator Replacement Options
Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators
As an Amazon Associate, we earn from qualifying purchases.
Browse all Whirlpool error codes: Whirlpool Error Codes
April 16, 2026
How to Fix Frigidaire Refrigerator Error SY CF
Error Code: SY CF Difficulty: Hard

Problem: Condenser Fan Motor Failure (Alternate Code)

How to Fix SY CF Error (Step-by-Step)
1. Unplug the refrigerator from the wall outlet for safety and confirm the error stays cleared during a full test cycle.
2. Pull the refrigerator away from the wall to access the lower rear service panel.
3. Using a screwdriver or nut driver, remove the screws holding the service panel in place and set it aside.
4. Locate the condenser fan motor, which is mounted near the large, black compressor. You will see a fan blade attached to it.
5. Disconnect the wire harness from the motor. Remove the mounting screws that hold the motor and its bracket to the refrigerator’s frame.
6. Install the new condenser fan motor (Part #5304504528 or #242058232), making sure to transfer the fan blade if necessary. Secure it with the mounting screws and reconnect the wire harness.
7. Reinstall the rear service panel, plug the refrigerator in, and slide it back into place. The error should clear once the unit powers on.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Frigidaire Refrigerator

Focused repair path: refrigerator door, airflow, sensor, defrost, dispenser, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.
1. Confirm the doors close fully, the gaskets seal, and the display is not reacting to a door left open or a blocked switch.
2. Check for blocked vents, heavy frost, stalled fans, warm compartments, or recent power interruptions before replacing electronic parts.
3. If the code involves temperature or airflow, inspect the evaporator fan, thermistor, defrost path, wiring, and control connections.
4. If the symptom follows a door or dispenser event, check the switch, harness, hinge wiring, and connector seating first.
5. Use the full Frigidaire refrigerator model number before buying parts because sensors, boards, fans, and switches are model-specific.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Frigidaire model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.
&tag=appliancefixg-20
Verified Compatible Alternatives:
- 5304504528
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.
- [OK]Water inlet valve, ice maker, or fan failures keep returning
- [OK]Defrost heater, thermostat, or sensor faults stack up
- [OK]Compressor or sealed-system repair is not economical
- [OK]Food-loss risk is becoming a pattern
Recommended Refrigerator Replacement Options
Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Frigidaire error codes: Frigidaire Error Codes
April 16, 2026
How to Fix Maytag Dishwasher Error 3-3
Problem: OWI failed to calibrate or drain hose check valve issue

How to Fix Dishwasher Error
1. Turn off power and water supply to the dishwasher.
2. Remove the lower access panel.
3. Check the drain hose routing for proper high loop installation.
4. Inspect the drain hose check valve for debris or damage.
5. Remove the drain hose from air gap or sink connection.
6. Flush the drain hose with hot water to remove obstructions.
7. If the check valve is faulty, replace the entire drain hose assembly.
8. Test the OWI (turbidity) sensor operation by running calibration cycle.
9. If the sensor fails calibration repeatedly, replace the OWI sensor assembly.
10. Clear error codes and verify proper operation.
As an Amazon Associate, we earn from qualifying purchases through links on this page.

Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Maytag error codes: Maytag Error Codes
When It’s Better to Replace Than Repair

Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
Here are a few signs it may be time to shop for a new one:
- ✓Appliance over 8-10 years old
- ✓Repair cost over 50% of replacement
- ✓Multiple recent breakdowns
- ✓Major component failure
Recommended Replacement Options
Budget Option

Top Rated Washers Under $600

Amazon’s Highest-Rated Value Models

Free ‘Room of Choice’ Delivery Available

Professional Haul-away Options at Checkout

View Top Rated Models & Delivery Options

Mid-Range Option

Top Rated Washers $600 to $1,000

Best-Sellers with Thousands of 5-Star Reviews

Expert Installation & Hookup Services available

Protection Plans for Long-Term Peace of Mind

View Top Rated Models & Delivery Options

Premium Option

Top Rated Washers Over $1,000

Top-of-the-Line Performance & Technology

White-Glove Delivery and Haul-away eligible

Comprehensive Warranty & Support Options

View Top Rated Models & Delivery Options
Why Upgrade via Amazon?

Fast, Scheduled Delivery – You pick the date and time

Expert Installation – Professional setup available for most models

Old Appliance Haul-away – They’ll take your broken unit when they leave

Easy Returns – Buy with confidence from a leader in customer service
As an Amazon Associate, we earn from qualifying purchases.
April 16, 2026
How to Fix Frigidaire Refrigerator Error SH
Error Code: SH Difficulty: Moderate

Problem: Shorted Sensor (e.g., Temperature Sensor)

How to Fix SH Error (Step-by-Step)
1. Unplug the refrigerator from the wall outlet to ensure your safety.
2. Locate the faulty temperature sensor. It is typically inside the fresh food compartment, behind a small plastic cover along the top or back wall.
3. Remove any shelves that are in the way. Use a small flathead screwdriver to gently pry off the plastic sensor cover.
4. Disconnect the sensor by pressing the locking tab on the wire harness connector and pulling it apart.
5. Connect the new temperature sensor (Part #240597203) to the wire harness. You should hear a click as it locks into place.
6. Snap the plastic cover back over the new sensor and reinstall any shelves you removed.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Frigidaire Refrigerator

Focused repair path: refrigerator door, airflow, sensor, defrost, dispenser, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.
1. Confirm the doors close fully, the gaskets seal, and the display is not reacting to a door left open or a blocked switch.
2. Check for blocked vents, heavy frost, stalled fans, warm compartments, or recent power interruptions before replacing electronic parts.
3. If the code involves temperature or airflow, inspect the evaporator fan, thermistor, defrost path, wiring, and control connections.
4. If the symptom follows a door or dispenser event, check the switch, harness, hinge wiring, and connector seating first.
5. Use the full Frigidaire refrigerator model number before buying parts because sensors, boards, fans, and switches are model-specific.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Frigidaire model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.
&tag=appliancefixg-20
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.
- [OK]Water inlet valve, ice maker, or fan failures keep returning
- [OK]Defrost heater, thermostat, or sensor faults stack up
- [OK]Compressor or sealed-system repair is not economical
- [OK]Food-loss risk is becoming a pattern
Recommended Refrigerator Replacement Options
Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Frigidaire error codes: Frigidaire Error Codes
April 16, 2026
How to Fix Whirlpool Refrigerator Error Er 20F
Problem: Control board watchdog timer failure – processor locked up

How to Fix Refrigerator Error
1. Unplug refrigerator for 10 minutes to fully reset processor.
2. Remove rear access panel to access main control board.
3. Inspect board for signs of overheating (discolored components near processor).
4. Check ventilation around control compartment – ensure no dust buildup blocking airflow.
5. Verify ambient temperature isn’t exceeding 120°F near control board location.
6. Test all input devices (door switches, temperature sensors) for intermittent shorts that could crash processor.
7. If no external causes found and error recurs within 3 cooling cycles, control board processor has failed.
8. Replace main control board assembly W
9. During installation, ensure board mounting screws are tight to provide proper heat sinking.
10. After replacement, monitor refrigerator through 3 complete cooling cycles to confirm stability. Document any power interruptions that preceded failure – may indicate need for surge protection.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
Recommended Parts to Check

This page already had a Whirlpool part recommendation. Verify the complete appliance model number before ordering, because part fit can vary by model revision.
- Whirlpool part search: W11035831
  
  Estimated part range: $240
  
  Fit note: Confirm this part against the full Whirlpool refrigerator model number before buying.
  
  Search Amazon for W11035831
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.
- [OK]Water inlet valve, ice maker, or fan failures keep returning
- [OK]Defrost heater, thermostat, or sensor faults stack up
- [OK]Compressor or sealed-system repair is not economical
- [OK]Food-loss risk is becoming a pattern
Recommended Refrigerator Replacement Options
Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators
As an Amazon Associate, we earn from qualifying purchases.
Browse all Whirlpool error codes: Whirlpool Error Codes
April 16, 2026
How to Fix Frigidaire Refrigerator Error PF
Error Code: PF Difficulty: Easy

Problem: Power Failure. Indicates the unit has lost and regained power.

How to Fix PF Error (Step-by-Step)
1. This code indicates a recent power outage, not a part failure. First, check the food in the refrigerator and freezer for signs of spoilage.
2. Press any button on the control panel, or look for a specific ‘Alarm Reset’ or ‘OK’ button, to acknowledge the alert and clear the code from the display.
3. Verify that the refrigerator is plugged securely into a working outlet.
4. Check your home’s circuit breaker box to ensure the breaker for the refrigerator has not tripped.
5. Allow the refrigerator several hours to return to its set temperatures. Monitor the display to confirm it is cooling correctly.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
What to Check Next on This Frigidaire Refrigerator

Focused repair path: refrigerator door, airflow, sensor, defrost, dispenser, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.
1. Confirm the doors close fully, the gaskets seal, and the display is not reacting to a door left open or a blocked switch.
2. Check for blocked vents, heavy frost, stalled fans, warm compartments, or recent power interruptions before replacing electronic parts.
3. If the code involves temperature or airflow, inspect the evaporator fan, thermistor, defrost path, wiring, and control connections.
4. If the symptom follows a door or dispenser event, check the switch, harness, hinge wiring, and connector seating first.
5. Use the full Frigidaire refrigerator model number before buying parts because sensors, boards, fans, and switches are model-specific.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Frigidaire model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Frigidaire refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool refrigerator thermistor
  
  Common replacement category: Temperature sensor / thermistor
  
  Fit note: Exact OEM part number varies by complete Frigidaire refrigerator model number. Confirm compatibility before buying.
  
  Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.
  
  Search Amazon for Whirlpool refrigerator thermistor
- Whirlpool refrigerator evaporator fan motor
  
  Common replacement category: Evaporator fan motor
  
  Fit note: Exact OEM part number varies by complete Frigidaire refrigerator model number. Confirm compatibility before buying.
  
  Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.
  
  Search Amazon for Whirlpool refrigerator evaporator fan motor
- Whirlpool refrigerator control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Frigidaire refrigerator model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.
  
  Search Amazon for Whirlpool refrigerator control board
Before ordering: match the part to the complete Frigidaire refrigerator model number on the appliance tag.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.
- [OK]Water inlet valve, ice maker, or fan failures keep returning
- [OK]Defrost heater, thermostat, or sensor faults stack up
- [OK]Compressor or sealed-system repair is not economical
- [OK]Food-loss risk is becoming a pattern
Recommended Refrigerator Replacement Options
Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Frigidaire error codes: Frigidaire Error Codes
April 16, 2026