Author: Patch

  • How to Fix Amana Dryer Error E3

    How to Fix Amana Dryer Error E3

    Error Code: E3 Difficulty: Easy

    Problem: Signals that the dryer is overheating or has a temperature sensor issue, often due to a faulty thermistor or restricted airflow.

    How to Fix E3 Error (Step-by-Step)

    1. Unplug the dryer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Pull out the lint screen and thoroughly clean off all lint and debris.
    3. Inspect the lint screen housing for any accumulated lint that might be causing a blockage and use a vacuum with a narrow attachment to clean it out.
    4. Move the dryer away from the wall to access the exhaust vent.
    5. Disconnect the vent from the back of the dryer and check for any clogs or kinks in the ducting.
    6. Clean the entire length of the vent from the dryer to the outside of the house.
    7. Once everything is clear, reconnect the vent, plug the dryer back in, and try running a cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Whirlpool Dryer Error F22

    How to Fix Whirlpool Dryer Error F22

    Problem: The outlet temperature sensor is bad. The dryer has stopped heating for safety because it can’t read the exhaust temperature. Replace the thermistor on the blower housing.

    How to Fix F22 Error

      • UNPLUG dryer from electrical power. Pull unit away from wall for rear access.
      • Remove rear panel to access blower housing assembly.
      • Locate exhaust thermistor mounted on blower housing near exhaust duct connection.
      • Disconnect thermistor wiring harness. Note routing path before removal.
      • Measure resistance across thermistor terminals with multimeter at room temperature. Should read approximately 10kΩ (±10%).
      • If reading is infinite (open) or near zero (shorted), replace thermistor.
      • Remove mounting screw or clip securing sensor. Gently pull thermistor from housing well.
      • Install new thermistor using OEM part WPW
      • Ensure sensor tip makes full contact with housing wall.
      • Route wiring away from heating element and moving parts. Reconnect harness securely.
      • Reinstall rear panel. Restore power. Run timed dry cycle on high heat to verify exhaust temperature readings stabilize correctly.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Amana Dryer Error AF

    How to Fix Amana Dryer Error AF

    Error Code: AF Difficulty: Easy

    Problem: Restricted airflow is detected. This can be caused by a clogged lint screen, a kinked or crushed vent, or a blockage in the vent.

    How to Fix AF Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Locate and remove the lint screen, which is usually found just inside the dryer door opening.
    3. Clean all lint and debris from the screen using your fingers. For stubborn residue, wash the screen with warm, soapy water and a soft brush, then rinse and dry it completely before reinserting.
    4. Use a vacuum cleaner with a long, narrow attachment to clean out the cavity where the lint screen is housed.
    5. Go behind the dryer and disconnect the flexible vent hose from both the dryer and the wall exhaust port.
    6. Inspect the entire length of the vent hose for any kinks, crushed sections, or blockages. Clear any obstructions you find.
    7. Check the exterior vent hood on the outside of your house to ensure the flap moves freely and is not blocked by lint, nests, or other debris.
    8. Once clear, reattach the vent hose securely at both ends, plug the dryer back in, and run a cycle to test.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Whirlpool Dryer Error F23

    How to Fix Whirlpool Dryer Error F23

    Problem: Electronic control board failure with specific fault in user interface or display circuitry affecting operational controls.

    How to Fix Dryer Error

    Consult manual.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes