Category: Electrolux

How to Fix Electrolux Dryer Error E41
Error Code: E41 Difficulty: Moderate

Problem: Door opened at start.

How to Fix E41 Error (Step-by-Step)
1. Unplug the dryer from the wall outlet and confirm the error stays cleared during a full test cycle.
2. Open the dryer door and locate the door switch, typically a small plastic component that is pressed when the door closes.
3. Check if the door switch clicks when you press and release it. If it doesn’t, it may be faulty.
4. Inspect the wiring connected to the door switch for any loose or damaged connections.
5. If the switch and wiring appear to be in good condition, the issue may lie with the door latch and strike. Ensure they align and engage correctly.
6. If the problem persists, the door switch assembly may need to be replaced.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 5366021400
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
April 29, 2026
How to Fix Electrolux Dryer Error E40
Error Code: E40 Difficulty: Easy

Problem: Door is open.

How to Fix E40 Error (Step-by-Step)
1. Ensure the dryer door is completely closed and latched and confirm the error stays cleared during a full test cycle.
2. Check for any clothing or foreign objects that may be obstructing the door from closing properly.
3. Inspect the door strike to ensure it aligns with the door latch assembly.
4. Gently clean the area around the door latch and strike to remove any lint or debris buildup.
5. Press the ‘Start’ button again after ensuring the door is securely shut.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
April 29, 2026
How to Fix Electrolux Dryer Error E4
Error Code: E4 Difficulty: Moderate

Problem: Humidity Sensor Failed.

How to Fix E4 Error (Step-by-Step)
1. Unplug the dryer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
2. Locate the humidity sensor inside the dryer drum, usually near the lint filter housing. It consists of two metal strips.
3. Clean the sensor strips with a soft cloth and rubbing alcohol to remove any residue or fabric softener buildup.
4. Inspect the wiring connected to the humidity sensor. Ensure the connections are secure and not damaged.
5. If cleaning and checking the wiring doesn’t resolve the issue, the humidity sensor may need to be replaced.
6. For persistent issues, the main control board may be at fault and require testing and potential replacement by a professional.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 134786110
- 134994700
- 5304515376
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
April 29, 2026
How to Fix Electrolux Dryer Error E32
Error Code: E32 Difficulty: Hard

Problem: Moisture sensor frequency is too low.

How to Fix E32 Error (Step-by-Step)
1. Disconnect the dryer from the electrical outlet to prevent shock.
2. Locate the moisture sensor bars (Part 134786110) inside the dryer drum. Inspect them for any foreign objects, such as a coin or paperclip, that could be shorting them out.
3. Clean the sensor bars with rubbing alcohol and a clean cloth to remove any potential conductive residue.
4. Access the back of the moisture sensor and inspect the wire harness (Part 5304515376). Ensure the wires are not pinched, frayed, or shorting against the dryer’s metal chassis.
5. Disconnect the sensor harness from the main control board and test the sensor circuit for continuity. A continuous short indicates a problem with the wiring or sensors.
6. If the sensors and wiring are in good condition, the problem points to a failure in the main control board (Part 134994700), which will need to be replaced.
7. Carefully install the new control board, reconnect all harnesses, and reassemble the unit.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 134786110
- 134994700
- 5304515376
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
April 29, 2026
How to Fix Electrolux Dryer Error E31
Error Code: E31 Difficulty: Hard

Problem: Moisture sensor frequency is too high.

How to Fix E31 Error (Step-by-Step)
1. Unplug the dryer from the power outlet and confirm the error stays cleared during a full test cycle.
2. Open the dryer door and locate the two metal moisture sensor bars (Part 134786110) inside the drum, usually near the lint filter housing.
3. Clean the surfaces of the sensor bars thoroughly with a cotton ball or soft cloth dampened with rubbing alcohol. This removes any film from fabric softener sheets or detergents.
4. Trace the wires from the sensor bars back to the main control board. Check the wire harness (Part 5304515376) for any loose connections, breaks, or damage.
5. If cleaning the sensors and checking the wiring does not resolve the issue, the fault is likely with the main control board (Part 134994700).
6. Access and replace the main control board, carefully transferring all wire connections to the new board.
7. Reassemble the dryer and test a sensor-dry cycle and confirm the error stays cleared during a full test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 134786110
- 134994700
- 5304515376
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
April 29, 2026
How to Fix Electrolux Dryer Error E30
Error Code: E30 Difficulty: Hard

Problem: Drum overfilled.

How to Fix E30 Error (Step-by-Step)
1. Disconnect the dryer from its power supply and confirm the error stays cleared during a full test cycle.
2. Open the dryer door and inspect the drum for any foreign objects or tangled clothing that could cause an overfill condition.
3. Check the moisture sensor bars inside the drum. Clean them with a soft cloth and rubbing alcohol to remove any residue from fabric softeners.
4. If the drum is clear and sensors are clean, the issue likely lies with the electronic controls.
5. Access the main control board (Part 134994700) by removing the top or front panel of the dryer.
6. Inspect the board for any visible signs of damage or burnt components. If damage is found, the board must be replaced.
7. Carefully replace the control board, ensuring all wire connections are secure.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 134994700
- 5304515407
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
April 29, 2026
How to Fix Electrolux Dryer Error E24
Error Code: E24 Difficulty: Hard

Problem: Fault in the compressor cooling fan sensor circuit.

How to Fix E24 Error (Step-by-Step)
1. Unplug the dryer from the wall outlet and confirm the error stays cleared during a full test cycle.
2. Remove the rear access panel to gain access to the internal components.
3. Locate the compressor cooling fan (Part 134587700) and the associated thermistor/sensor (Part 134711200).
4. Visually inspect the fan for any obstructions, debris, or damage that might prevent it from spinning.
5. Check the wiring to both the fan motor and the sensor for any loose connections, breaks, or burn marks.
6. If the wiring is intact, you can test the fan motor and the thermistor with a multimeter for proper resistance. If either fails the test, it must be replaced.
7. Install the new part(s), reattach the rear panel, and plug the dryer in to test its operation.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 134711200
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
April 29, 2026
How to Fix Electrolux Dryer Error E23
Error Code: E23 Difficulty: Hard

Problem: The frequency of the capacitive level sensor is outside the acceptable range.

How to Fix E23 Error (Step-by-Step)
1. Ensure the dryer is completely disconnected from power and confirm the error stays cleared during a full test cycle.
2. Locate the capacitive level sensor (Part 5304521373), which is part of the main control board assembly in many models.
3. Access the main control board, typically behind the top or front control panel.
4. Carefully disconnect the wiring harnesses connected to the board and confirm the error stays cleared during a full test cycle.
5. Unmount and remove the entire control board assembly and confirm the error stays cleared during a full test cycle.
6. Replace it with the new control board/sensor assembly and confirm the error stays cleared during a full test cycle.
7. Securely reconnect all wiring and reassemble the dryer panels before restoring power.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
April 29, 2026
How to Fix Electrolux Dryer Error E22
Error Code: E22 Difficulty: Hard

Problem: Condensate pump is defective or blocked.

How to Fix E22 Error (Step-by-Step)
1. Turn off and unplug the dryer and confirm the error stays cleared during a full test cycle.
2. Locate the condensate pump (Part 134523200). This is often found at the base of the unit.
3. Inspect the pump and its connected hoses (Part 137249900) for any visible blockages or lint buildup.
4. Disconnect the hoses from the pump and flush them with water to ensure they are clear.
5. Check the pump’s impeller to see if it can move freely. If it is stuck or broken, the pump needs to be replaced.
6. If the pump and hoses are clear, use a multimeter to test the pump motor for continuity. If there is no continuity, replace the pump.
7. Reassemble all components and test the dryer and confirm the error stays cleared during a full test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 137249900
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
April 29, 2026
How to Fix Electrolux Dryer Error E21
Error Code: E21 Difficulty: Hard

Problem: Faulty canister fill pump triac.

How to Fix E21 Error (Step-by-Step)
1. Disconnect the dryer from the power source completely and confirm the error stays cleared during a full test cycle.
2. Access the main control board. This is typically located behind the main control panel or on a side panel.
3. Carefully label and disconnect all wire harnesses attached to the old control board (Part 134994700).
4. Remove the screws or clips holding the control board in place and gently remove it.
5. Install the new control board, ensuring it is securely mounted.
6. Reconnect all wire harnesses to their correct terminals on the new board.
7. Reassemble the dryer panels and plug it back in to test.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 134994700
- 137108100
- 137221600
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
April 29, 2026