Category: Electrolux

  • How to Fix Electrolux Dryer Error E58

    How to Fix Electrolux Dryer Error E58

    Error Code: E58 Difficulty: Hard

    Problem: High current on motor phase.

    How to Fix E58 Error (Step-by-Step)

    1. Disconnect the dryer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Access the motor and the inverter board by removing the dryer’s service panels.
    3. Examine the wires connecting the motor to the inverter board for any damage.
    4. If the wires are intact, the issue is likely with the motor or the inverter board.
    5. Test the motor windings with a multimeter to see if they are shorted.
    6. If the motor tests fine, the inverter board is the most likely cause of the problem and should be replaced.
    7. After replacing the faulty component, reassemble the dryer and plug it back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134735700
    • 137099100
    • 137261100

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E57

    How to Fix Electrolux Dryer Error E57

    Error Code: E57 Difficulty: Hard

    Problem: High current on inverter.

    How to Fix E57 Error (Step-by-Step)

    1. Unplug the dryer from its power source and confirm the error stays cleared during a full test cycle.
    2. Remove the necessary panels to access the inverter board and motor.
    3. Visually inspect the inverter board for any signs of burns or damage.
    4. Check the wiring between the inverter board and the motor for any loose or frayed connections.
    5. If the wiring is secure, the inverter board is likely the issue and needs to be replaced.
    6. Carefully disconnect all wires from the old inverter board and remove it.
    7. Install the new inverter board, reconnect all wiring, reassemble the dryer, and test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134735700
    • 137099100
    • 137261100

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E56

    How to Fix Electrolux Dryer Error E56

    Error Code: E56 Difficulty: Hard

    Problem: High motor current.

    How to Fix E56 Error (Step-by-Step)

    1. Turn off the power to the dryer at the circuit breaker.
    2. Open the dryer’s access panel to get to the motor.
    3. Check for any obstructions around the drum that could be causing the motor to work harder.
    4. Inspect the drive belt for signs of wear or damage and replace it if necessary.
    5. If the belt is fine and there are no obstructions, the motor itself may be faulty.
    6. Replace the motor by disconnecting it from its mount and the electrical connections.
    7. Install the new motor, reassemble the dryer, and restore power to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134735700
    • 5304529782

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E55

    How to Fix Electrolux Dryer Error E55

    Error Code: E55 Difficulty: Hard

    Problem: Motor overheating.

    How to Fix E55 Error (Step-by-Step)

    1. Disconnect the power to the dryer by unplugging it and confirm the error stays cleared during a full test cycle.
    2. Check the dryer’s ventilation for any blockages that could cause overheating.
    3. Remove the rear panel to access the motor and confirm the error stays cleared during a full test cycle.
    4. Examine the motor for any visible signs of damage or overheating.
    5. If the motor is hot to the touch, allow it to cool down completely.
    6. Replace the motor if it appears damaged or continues to overheat after clearing any vent blockages.
    7. Reassemble the dryer and test its operation and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134735700
    • 5304529782

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E54

    How to Fix Electrolux Dryer Error E54

    Error Code: E54 Difficulty: Hard

    Problem: Motor sensing failure.

    How to Fix E54 Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet to ensure safety.
    2. Access the back of the dryer to locate the motor.
    3. Inspect the wiring harness connected to the motor for any loose or damaged wires.
    4. Disconnect the wiring harness from the motor and confirm the error stays cleared during a full test cycle.
    5. Remove the mounting bolts that hold the motor in place and carefully take out the old motor.
    6. Install the new motor and secure it with the mounting bolts.
    7. Reconnect the wiring harness and ensure it is firmly attached, then reassemble and test the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134735700
    • 809160303
    • 5304521373

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E53

    How to Fix Electrolux Dryer Error E53

    Error Code: E53 Difficulty: Hard

    Problem: Motor centrifugal switch failure.

    How to Fix E53 Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall outlet.
    2. Remove the top panel of the dryer by unscrewing the screws holding it in place.
    3. Locate the motor and the centrifugal switch attached to it.
    4. Carefully disconnect the wires leading to the centrifugal switch and confirm the error stays cleared during a full test cycle.
    5. Replace the old motor assembly, which includes the centrifugal switch, with the new one.
    6. Reconnect the wires to the new switch and ensure all connections are secure.
    7. Reassemble the dryer by securing the top panel and plugging it back into the power outlet.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134735700
    • 809160303
    • 5304521373

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E51

    How to Fix Electrolux Dryer Error E51

    Error Code: E51 Difficulty: Hard

    Problem: Motor relay failure.

    How to Fix E51 Error (Step-by-Step)

    1. Disconnect the dryer from the electrical outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the top panel of the dryer to access the main control board.
    3. Locate the motor relay on the control board. It is a small, usually rectangular, component.
    4. Visually inspect the relay and the surrounding area on the circuit board for any signs of burning or damage.
    5. The motor relay is an integrated part of the main control board and cannot be replaced separately.
    6. If the relay is faulty, the entire main control board must be replaced.
    7. It is advisable to have a professional service confirm the diagnosis and perform the control board replacement.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134994700
    • 5304515407

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E50

    How to Fix Electrolux Dryer Error E50

    Error Code: E50 Difficulty: Hard

    Problem: Motor or software problem.

    How to Fix E50 Error (Step-by-Step)

    1. Unplug the dryer from the power source to prevent electrical shock.
    2. Remove the rear panel to access the drive motor and control board.
    3. Check the wiring connections to the motor and the main control board. Ensure they are secure and not damaged.
    4. Inspect the drive belt to make sure it is not broken or slipped off the motor pulley and drum.
    5. If the wiring and belt are intact, there may be an issue with the motor itself or a fault in the main control board’s software.
    6. A service can perform check tests on the motor and control board to determine the exact cause.
    7. Depending on the diagnosis, either the motor or the main control board will need to be replaced.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 137116000
    • 5304529782

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E45

    How to Fix Electrolux Dryer Error E45

    Error Code: E45 Difficulty: Hard

    Problem: Faulty door closing sensor.

    How to Fix E45 Error (Step-by-Step)

    1. Turn off the circuit breaker for the dryer and unplug it.
    2. Remove the top and front panels of the dryer to gain access to the door switch and main control board.
    3. Carefully examine the wiring harness connecting the door switch to the control board for any loose connections or damage.
    4. Test the door switch with a multimeter for proper operation. The switch should close the circuit when the door is shut.
    5. If the door switch is functioning correctly, the problem is likely with the main control board.
    6. Visually inspect the control board for any burn marks or damaged components.
    7. Replacing the main control board is a complex task and should be performed by a service service.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134994700
    • 137538802
    • 5304515407

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E42

    How to Fix Electrolux Dryer Error E42

    Error Code: E42 Difficulty: Hard

    Problem: Door sensing error.

    How to Fix E42 Error (Step-by-Step)

    1. Disconnect the dryer from its power source and confirm the error stays cleared during a full test cycle.
    2. Access the door switch and latch assembly by removing the necessary panels.
    3. Visually inspect the wiring between the door switch and the main control board for any signs of damage, such as burns or breaks.
    4. Use a multimeter to test the continuity of the door switch. It should have continuity when the button is pressed and no continuity when released.
    5. If the door switch tests fine, the issue may be with the main control board’s door sensing circuit.
    6. Inspect the control board for any visible signs of damage. Replacement of the control board is often necessary if it is found to be faulty.
    7. Due to the complexity, it is recommended to have a qualified service diagnose and replace the main control board.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134994700
    • 137538802
    • 5304515407

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes