Category: Dishwasher

How to Fix Electrolux Dishwasher Error I5E
Error Code: I5E Difficulty: Hard

Problem: Wash motor error.

How to Fix I5E Error (Step-by-Step)
1. Shut off the electricity to the dishwasher at your home’s circuit breaker panel.
2. Turn off the hot water supply line, which is usually located under the kitchen sink.
3. Gently pull the dishwasher out from under the counter to access the wash motor at the base.
4. Visually inspect the wash motor for any obvious signs of damage or blockages in the pump housing.
5. Carefully check the electrical connections on the motor, ensuring the wire harness is securely plugged in and shows no signs of damage.
6. If the connections are secure and there are no blockages, the motor itself has likely failed.
7. Replace the entire wash motor and pump assembly, reconnect the wiring and hoses, and then restore power and water.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154853801
- 807473201
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 11, 2026
How to Fix Electrolux Dishwasher Error I5F
Error Code: I5F Difficulty: Hard

Problem: Drain pump motor connection fault.

How to Fix I5F Error (Step-by-Step)
1. Turn off the power to your dishwasher at the main circuit breaker.
2. Shut off the water supply from the valve under the sink.
3. Slide the dishwasher out from the cabinetry to access the bottom components.
4. Locate the drain pump and its wiring harness and confirm the error stays cleared during a full test cycle.
5. Carefully unplug and re-plug the wire connector to the drain pump to ensure it has a solid connection.
6. Examine the wires in the harness for any breaks, frayed insulation, or signs of corrosion.
7. If the wiring appears intact, the fault is likely with the pump’s internal electronics, requiring the drain pump to be replaced.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- A00044305
- 5304524920
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 11, 2026
How to Fix Electrolux Dishwasher Error IB0
Error Code: IB0 Difficulty: Hard

Problem: Turbidity sensor problem.

How to Fix IB0 Error (Step-by-Step)
1. Turn off the power supply to the dishwasher at the circuit breaker.
2. Slide the dishwasher out and tilt it to access the sump area at the bottom.
3. Locate the turbidity sensor, which looks like a small plastic eye, mounted in the sump assembly.
4. Disconnect the wire harness from the sensor and confirm the error stays cleared during a full test cycle.
5. Gently remove the sensor from the sump. It may twist and pull out.
6. Clean the lens of the sensor with a soft cloth and mild detergent, as food soil can obstruct its reading.
7. If cleaning does not solve the problem, replace the turbidity sensor with a new part.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154762601
- 5304434905
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 11, 2026
How to Fix Electrolux Dishwasher Error ID0
Error Code: ID0 Difficulty: Hard

Problem: Motor tacho fault.

How to Fix ID0 Error (Step-by-Step)
1. Disconnect the dishwasher from power at the circuit breaker and shut off the hot water supply valve, usually located under the kitchen sink.
2. Carefully pull the dishwasher out from under the counter. You may need to remove two mounting screws that secure the dishwasher to the countertop.
3. Lay the dishwasher on its back on a towel or blanket to protect the floor and the appliance. This will give you access to the wash pump and motor assembly underneath.
4. Place a shallow pan and towel under the existing pump to catch residual water. Loosen the hose clamps and disconnect the hoses from the pump. Then, unplug the electrical wire connectors attached to the motor.
5. Locate and remove the mounting screws or brackets holding the wash pump and motor assembly in place. Remove the old assembly from the dishwasher.
6. Install the new wash pump and motor assembly, securing it with the mounting hardware. Reconnect the hoses and tighten the clamps securely to prevent leaks. Plug the electrical connectors back into the new motor.
7. Carefully tilt the dishwasher upright, slide it partially back in, and reconnect the power and water supply. Run a short rinse cycle to check thoroughly for any leaks before fully reinstalling the unit under the counter.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Electrolux dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.
  
  Search Amazon for Electrolux dishwasher drain pump
- Electrolux dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill or low-water symptoms after supply and float checks.
  
  Search Amazon for Electrolux dishwasher water inlet valve
- Electrolux dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating control faults after latch, wiring, and power checks.
  
  Search Amazon for Electrolux dishwasher control board
Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 11, 2026
How to Fix Electrolux Dishwasher Error IF1
Error Code: IF1 Difficulty: Hard

Problem: High water level / Diverter valve fault.

How to Fix IF1 Error (Step-by-Step)
1. Shut off the power to your dishwasher from your home’s circuit breaker.
2. You will need to pull the dishwasher out from under the counter to access the diverter valve and circulation pump.
3. After pulling the unit out, carefully tilt it on its back to get to the components underneath. Place a towel down to protect your floor.
4. Locate the diverter valve (part A00056504) and the circulation pump (part 154844001). Inspect them for any visible signs of damage or blockage.
5. To replace the diverter valve, disconnect the attached hoses and electrical connector, then remove the screws holding it in place. Install the new valve and reconnect everything.
6. For the circulation pump, disconnect its hoses and wiring, then unbolt it from the sump. Install the new pump, ensuring all connections are tight.
7. Carefully set the dishwasher upright, slide it back into place, and restore power to test its function.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- A00056504
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 11, 2026
How to Fix Electrolux Dishwasher Error C4
Error Code: C4 Difficulty: Hard

Problem: Tank temperature sensor out of order.

How to Fix C4 Error (Step-by-Step)
1. Disconnect the dishwasher from power and water supplies and confirm the error stays cleared during a full test cycle.
2. Locate the tank temperature sensor, usually at the bottom of the tub.
3. Disconnect the wiring harness from the old sensor and confirm the error stays cleared during a full test cycle.
4. Remove the old sensor by twisting it counter-clockwise and confirm the error stays cleared during a full test cycle.
5. Install the new sensor, ensuring a tight seal and confirm the error stays cleared during a full test cycle.
6. Reconnect the wiring harness and restore power and water and confirm the error stays cleared during a full test cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error C5
Error Code: C5 Difficulty: Hard

Problem: Tank temperature sensor out of order.

How to Fix C5 Error (Step-by-Step)
1. Turn off the power to the dishwasher at the circuit breaker.
2. Access the bottom of the dishwasher to find the tank temperature sensor.
3. Carefully unplug the two wires connected to the sensor and confirm the error stays cleared during a full test cycle.
4. Rotate the sensor to unlock and remove it from the sump.
5. Place the new sensor in the opening and turn to lock it in place.
6. Reattach the wires, and turn the power back on and confirm the error stays cleared during a full test cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error C8
Error Code: C8 Difficulty: Hard

Problem: Boiler does not empty during the rinse phase.

How to Fix C8 Error (Step-by-Step)
1. Shut off the power and water supply to the dishwasher.
2. Locate the boiler and its drain valve, typically underneath the unit.
3. Inspect the drain hose for any clogs or kinks and confirm the error stays cleared during a full test cycle.
4. Disconnect the electrical connectors from the drain valve and confirm the error stays cleared during a full test cycle.
5. Remove the mounting screws to replace the old valve and confirm the error stays cleared during a full test cycle.
6. Secure the new valve, reconnect the hoses and electrical connections, then test.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 0S2787
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error C9
Error Code: C9 Difficulty: Hard

Problem: Automatic hood is out of order.

How to Fix C9 Error (Step-by-Step)
1. De-energize the dishwasher by unplugging it or switching off the breaker.
2. Open the dishwasher door and remove the inner door panel screws.
3. Locate the automatic hood mechanism and control board and confirm the error stays cleared during a full test cycle.
4. Disconnect all wire harnesses from the control board and confirm the error stays cleared during a full test cycle.
5. Replace the control board and any faulty hood components and confirm the error stays cleared during a full test cycle.
6. Reassemble the door panel and restore power to test the new parts.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154663004
- 154750502
- 807024501
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error CL OR CD
Error Code: CL OR CD Difficulty: Easy

Problem: The dishwasher door is open.

How to Fix CL OR CD Error (Step-by-Step)
1. Ensure the dishwasher door is completely closed and latched and confirm the error stays cleared during a full test cycle.
2. Check for any obstructions like utensils or racks preventing the door from closing.
3. Inspect the door latch for any visible damage or misalignment.
4. Gently clean the door latch mechanism with a damp cloth.
5. Power cycle the dishwasher by turning it off and on at the circuit breaker.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Electrolux dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.
  
  Search Amazon for Electrolux dishwasher drain pump
- Electrolux dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill or low-water symptoms after supply and float checks.
  
  Search Amazon for Electrolux dishwasher water inlet valve
- Electrolux dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating control faults after latch, wiring, and power checks.
  
  Search Amazon for Electrolux dishwasher control board
Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026