Category: Dishwasher

  • How to Fix Electrolux Dishwasher Error AL5

    How to Fix Electrolux Dishwasher Error AL5

    Error Code: AL5 Difficulty: Hard

    Problem: Water inlet problem.

    How to Fix AL5 Error (Step-by-Step)

    1. Turn off the power to the dishwasher at your home’s circuit breaker.
    2. Shut off the water supply to the dishwasher, usually located under the sink.
    3. Carefully pull the dishwasher out from under the counter to access the water inlet hose and valve at the back or bottom.
    4. Inspect the water inlet hose for any kinks or sharp bends that could block water flow and straighten it if necessary.
    5. Unscrew the hose from the water inlet valve and check the small filter screen inside the valve’s port for any sediment or debris. Clean it with a small brush if it’s clogged.
    6. If the hose and screen are clear, the water inlet valve itself may be faulty and require replacement by a professional.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 807047901
    • 5304519252

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Electrolux Dishwasher Error AL6

    How to Fix Electrolux Dishwasher Error AL6

    Error Code: AL6 Difficulty: Hard

    Problem: Draining problem.

    How to Fix AL6 Error (Step-by-Step)

    1. Disconnect the dishwasher from its power source at the circuit breaker.
    2. Remove the lower front access panel (kickplate) to get to the drain pump and hose.
    3. Place a shallow pan and towels under the drain hose connection to catch any residual water.
    4. Check the entire length of the drain hose for any visible kinks or clogs. Squeeze the hose to feel for any blockages.
    5. Disconnect the drain hose from the drain pump and check the pump’s inlet for any debris or foreign objects that could be jamming the impeller.
    6. If the hose and pump are clear, the drain pump motor may have failed and will likely need to be tested and replaced by a service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • A00126401
    • 5304517581

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dishwasher Error AIRDRY

    How to Fix Electrolux Dishwasher Error AIRDRY

    Error Code: AIRDRY Difficulty: Easy

    Problem: Indicates that the AirDry function, which automatically opens the door at the end of the cycle to improve drying, is active.

    How to Fix AIRDRY Error (Step-by-Step)

    1. This is a normal operational message, not an error code. It indicates the AirDry feature is active.
    2. The dishwasher door is designed to automatically open a few inches after the cycle is complete.
    3. This process allows your dishes to dry naturally with room air, saving energy.
    4. If you prefer the door to remain closed, you can typically disable the AirDry function through your dishwasher’s settings menu.
    5. To turn the function off or on, consult the instructions specific to your model, often involving pressing a combination of buttons on the control panel.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dishwasher Error C12

    How to Fix Electrolux Dishwasher Error C12

    Error Code: C12 Difficulty: Hard

    Problem: Tank level sensor is out of order.

    How to Fix C12 Error (Step-by-Step)

    1. Shut off all power to the dishwasher from the main circuit breaker to ensure safety.
    2. To access the internal components, you will need to pull the dishwasher out from its installation spot.
    3. The tank level sensor is located in the sump area at the bottom of the dishwasher tub.
    4. Carefully disconnect the wire connector attached to the sensor and confirm the error stays cleared during a full test cycle.
    5. The sensor is usually removed by twisting it counter-clockwise to release it from its housing.
    6. Install the new sensor by aligning it and twisting it clockwise, then securely reattach the wire connector.
    7. Slide the dishwasher back into place, restore power, and run a test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dishwasher Error C2

    How to Fix Electrolux Dishwasher Error C2

    Error Code: C2 Difficulty: Hard

    Problem: Draining problem or boiler temperature is too high on professional models.

    How to Fix C2 Error (Step-by-Step)

    1. Turn off the dishwasher’s power at the circuit breaker and confirm the error stays cleared during a full test cycle.
    2. Open the dishwasher door and remove the bottom dish rack.
    3. Locate and remove the filter assembly at the bottom of the tub by twisting it loose. Clean it thoroughly under running water.
    4. Inspect the sump area below the filter for any food particles or debris and clean it out.
    5. Check the drain hose for any clogs or kinks that could prevent proper draining.
    6. On professional models, this can also indicate a high boiler temperature, which requires inspection of the temperature sensor and heating element by a qualified service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 1113160004
    • 5304483441

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dishwasher Error C6

    How to Fix Electrolux Dishwasher Error C6

    Error Code: C6 Difficulty: Hard

    Problem: Boiler temperature sensor out of order.

    How to Fix C6 Error (Step-by-Step)

    1. Disconnect the dishwasher from the power supply at your home’s circuit breaker panel.
    2. Pull the dishwasher out from under the counter to access the components underneath.
    3. Locate the boiler assembly and the temperature sensor that is mounted on it.
    4. Unplug the electrical connector from the sensor carefully and confirm the error stays cleared during a full test cycle.
    5. Remove the old sensor from the boiler. It may be held in place by a clip or be threaded.
    6. Install the new temperature sensor, ensuring it is securely fitted, and reconnect the electrical wires.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 1113160004
    • 5304483441

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dishwasher Error C7

    How to Fix Electrolux Dishwasher Error C7

    Error Code: C7 Difficulty: Hard

    Problem: Boiler temperature sensor out of order.

    How to Fix C7 Error (Step-by-Step)

    1. Begin by cutting power to the dishwasher at the circuit breaker for safety.
    2. Slide the dishwasher out from its installed position to access the underside components.
    3. Find the boiler and identify the temperature sensor connected to it.
    4. Gently detach the wiring harness from the temperature sensor and confirm the error stays cleared during a full test cycle.
    5. Carefully remove the old sensor from its mounting on the boiler.
    6. Fit the new temperature sensor into place and securely reattach the wiring harness.
    7. Reinstall the dishwasher, turn the power back on, and test its operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 1113160004
    • 5304483441

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dishwasher Error E01

    How to Fix Electrolux Dishwasher Error E01

    Error Code: E01 Difficulty: Hard

    Problem: A leak has been detected in the base of the dishwasher.

    How to Fix E01 Error (Step-by-Step)

    1. Turn off the power to the dishwasher at the circuit breaker.
    2. Pull the dishwasher out from under the counter to access the base.
    3. Locate the leak sensor (float switch) in the base pan.
    4. Inspect the base pan for any visible water and dry it thoroughly.
    5. Disconnect the wires from the leak sensor and remove it.
    6. Install the new leak sensor and reconnect the wiring and confirm the error stays cleared during a full test cycle.
    7. Check all hoses and connections for leaks before sliding the dishwasher back into place.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 154825501
    • 7154655901

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dishwasher Error F0

    How to Fix Electrolux Dishwasher Error F0

    Error Code: F0 Difficulty: Hard

    Problem: The pressure switch signal has not stabilized, indicating a potential water filling issue. This is not typically displayed to the user but stored in memory for service technicians.

    How to Fix F0 Error (Step-by-Step)

    1. Shut off the power to the dishwasher at the breaker.
    2. Pull the dishwasher out to access the side or base where the pressure switch is located.
    3. Find the pressure switch and the attached hose and confirm the error stays cleared during a full test cycle.
    4. Disconnect the wiring and the hose from the old pressure switch.
    5. Remove the old pressure switch from its mounting bracket and confirm the error stays cleared during a full test cycle.
    6. Install the new pressure switch, reconnecting the hose and wiring.
    7. Ensure the hose is not kinked or clogged before restoring power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 154513601
    • A00055408
    • 5304482406

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dishwasher Error F2

    How to Fix Electrolux Dishwasher Error F2

    Error Code: F2 Difficulty: Moderate

    Problem: Indicates a draining problem, which could be caused by a clogged drainage system or incorrect installation.

    How to Fix F2 Error (Step-by-Step)

    1. Disconnect the dishwasher from power and confirm the error stays cleared during a full test cycle.
    2. Check the drain hose for any kinks or clogs. Straighten any kinks you find.
    3. Disconnect the drain hose from the sink drain or garbage disposal to check for blockages.
    4. Clear any debris from the drain hose and the connection point.
    5. Inside the dishwasher, remove the filter and clean it thoroughly under running water.
    6. If the issue persists, the drain pump may need to be replaced.
    7. Reassemble all components and restore power and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • A00126401

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes