Category: Dishwasher

How to Fix Electrolux Dishwasher Error DELAY LIGHTS FLASHING
Error Code: DELAY LIGHTS FLASHING Difficulty: Moderate

Problem: This indicates a heating element failure, where the water did not reach the proper temperature in the allotted time.

How to Fix DELAY LIGHTS FLASHING Error (Step-by-Step)
1. Disconnect the dishwasher from its power source and confirm the error stays cleared during a full test cycle.
2. Access the heating element at the bottom of the dishwasher tub.
3. Disconnect the wires from the heating element terminals and confirm the error stays cleared during a full test cycle.
4. Remove the nuts holding the heating element in place and confirm the error stays cleared during a full test cycle.
5. Gently pull out the old heating element and install the new one.
6. Secure the new element with the nuts, reconnect the wires, and restore power.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154825001
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error ER-04 OR ER-05
Error Code: ER-04 OR ER-05 Difficulty: Moderate

Problem: There is a failure with the upper fan or vent.

How to Fix ER-04 OR ER-05 Error (Step-by-Step)
1. Turn off the power to the dishwasher at the main power supply.
2. Remove the dishwasher from its installation to access the top and back panels.
3. Locate the upper fan and vent assembly and confirm the error stays cleared during a full test cycle.
4. Disconnect the wiring to the fan motor and confirm the error stays cleared during a full test cycle.
5. Remove the screws securing the fan and vent assembly to replace it.
6. Reinstall all panels and slide the dishwasher back into place before restoring power.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154861101
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error ER-07 OR ER-11
Error Code: ER-07 OR ER-11 Difficulty: Moderate

Problem: There is a failure with the drain valve.

How to Fix ER-07 OR ER-11 Error (Step-by-Step)
1. Cut the power to the dishwasher from the fuse box.
2. Place towels under the dishwasher to catch any water and confirm the error stays cleared during a full test cycle.
3. The drain valve is located at the bottom of the dishwasher.
4. Disconnect the hose and the electrical connector from the valve.
5. Unfasten the old valve and install the new one and confirm the error stays cleared during a full test cycle.
6. Reconnect the hose and electrical wires, then turn the power back on to test.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error HD OR HO
Error Code: HD OR HO Difficulty: Easy

Problem: The dishwasher is in “Heat Delay” or “Heater On” mode, allowing the water to reach the optimal temperature.

How to Fix HD OR HO Error (Step-by-Step)
1. Do not be alarmed. This is not an error code, but a status indicator.
2. ‘hD’ or ‘HO’ means the dishwasher is in a ‘Heat Delay’ or ‘Heater On’ phase.
3. The dishwasher is simply waiting for the water to reach the correct temperature before starting the main wash cycle.
4. This ensures optimal cleaning and drying performance and confirm the error stays cleared during a full test cycle.
5. No action is required. Allow the dishwasher to complete its cycle normally.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Electrolux dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.
  
  Search Amazon for Electrolux dishwasher drain pump
- Electrolux dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill or low-water symptoms after supply and float checks.
  
  Search Amazon for Electrolux dishwasher water inlet valve
- Electrolux dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating control faults after latch, wiring, and power checks.
  
  Search Amazon for Electrolux dishwasher control board
Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error STATUS LIGHTS FLASHING AND DISHWASHER DRAINING
Error Code: STATUS LIGHTS FLASHING AND DISHWASHER DRAINING Difficulty: Hard

Problem: This indicates a shorted keypad.

How to Fix STATUS LIGHTS FLASHING AND DISHWASHER DRAINING Error (Step-by-Step)
1. Disconnect the dishwasher from power by turning off the circuit breaker.
2. Open the dishwasher door and remove the Torx screws holding the inner door panel to the outer panel.
3. Separate the inner and outer door panels to expose the internal components.
4. Carefully disconnect the ribbon cable that connects the keypad to the main control board.
5. Remove the screws holding the old keypad and control panel assembly in place and remove it.
6. Install the new control panel (Part #807545701), securing it with the screws.
7. Reconnect the ribbon cable to the control board, reassemble the door panels, and restore power to test the new keypad.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error I11
Error Code: I11 Difficulty: Moderate

Problem: Water supply error.

How to Fix I11 Error (Step-by-Step)
1. Turn off the power to the dishwasher at the circuit breaker.
2. Shut off the water supply to the dishwasher, usually from a valve under the sink.
3. Place a towel under the water inlet valve to catch any drips.
4. Unscrew the water supply line from the inlet valve and confirm the error stays cleared during a full test cycle.
5. Disconnect the wiring harness from the valve and remove the screws holding it in place.
6. Install the new water inlet valve (Part #154513601), ensuring all connections are secure.
7. Turn the water and power back on and check for leaks before starting a test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154513601
- 154757901
- 807445904
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error I20 / 20
Error Code: I20 / 20 Difficulty: Moderate

Problem: The dishwasher is not draining water properly. This can be caused by a clogged drain system, a defective or blocked drain pump, or a pinched or bent drain hose.

How to Fix I20 / 20 Error (Step-by-Step)
1. Turn off power to the dishwasher at the circuit breaker.
2. Check the drain hose for any kinks or bends that could restrict water flow. Straighten it if necessary.
3. Remove the bottom dish rack and clean the filter assembly at the bottom of the tub. Remove any food debris or blockages.
4. If the issue persists, you may need to access the drain pump. Disconnect the dishwasher and lay it on its back on a towel.
5. Remove the bottom access panel to locate the drain pump (Part #154757901).
6. Disconnect the hoses and wiring from the pump and check for blockages in the pump itself.
7. If the pump is clear but not working, replace it with a new one, reconnect everything, and test the dishwasher.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- A00044305
- 140000443030
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error I20, E20, 2 FLASHES
Error Code: I20, E20, 2 FLASHES Difficulty: Moderate

Problem: Draining issue. The dishwasher is not draining water properly.

How to Fix I20, E20, 2 FLASHES Error (Step-by-Step)
1. Disconnect the dishwasher from its power source at the circuit breaker.
2. Remove the bottom dish rack to access the filter and sump area at the bottom of the tub.
3. Unscrew and remove the filter assembly. Wash it thoroughly with warm, soapy water to remove any built-up grime.
4. Inspect the sump area below the filter for any foreign objects or debris that could be blocking the drain pump inlet.
5. If the filter and sump are clear, the issue may be the drain pump (Part #154757901). You will need to pull the dishwasher out to access it from underneath.
6. Check the pump for blockages or damage. If it appears faulty, replace it.
7. Reassemble all components, restore power, and run a drain cycle to confirm the repair.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- A00044305
- A00126401
- 5304524920
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error I30, E30, 3 FLASHES
Error Code: I30, E30, 3 FLASHES Difficulty: Hard

Problem: Anti-flood system activated. A leak has been detected in the base of the dishwasher.

How to Fix I30, E30, 3 FLASHES Error (Step-by-Step)
1. Turn the appliance off to the dishwasher immediately at the circuit breaker to prevent electrical hazards.
2. Pull the dishwasher out from under the counter to access the base pan.
3. You will likely find water in the base pan. Use towels or a sponge to completely dry the area.
4. The anti-flood system is triggered by a float switch (Part #154773201) that rises with the water level. Locate this switch in the base pan.
5. Once the pan is dry, the switch should reset. However, you must find the source of the leak (e.g., a loose hose, cracked pump, or bad seal).
6. After fixing the leak source, ensure the float switch moves freely and is not stuck.
7. Reinstall the dishwasher, restore power, and run a cycle while monitoring for any new leaks.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error I36
Error Code: I36 Difficulty: Hard

Problem: Water in the dishwasher base.

How to Fix I36 Error (Step-by-Step)
1. Shut off the power and water supply to the dishwasher.
2. Carefully slide the dishwasher out from its installation space. Place towels down to protect your floor.
3. Tip the unit forward at a 45-degree angle to allow water trapped in the base to drain out onto the towels.
4. With the unit on its back, inspect all hoses, the drain pump (Part #154859401), and the main sump for signs of cracks or loose connections that could be the source of the leak.
5. Check the door gasket (Part #154246801) for any tears or deformities that might prevent a proper seal.
6. Replace any damaged components you find and confirm the error stays cleared during a full test cycle.
7. After reassembly, run a test cycle and carefully inspect for any signs of water leakage before sliding the unit back into place.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154859401
- 5304512895
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026