Category: Electrolux

How to Fix Electrolux Washer Error B3
Error Code: B3 Difficulty: Hard

Problem: Supply voltage too low.

How to Fix B3 Error (Step-by-Step)
1. Unplug the washer from the electrical outlet to ensure safety.
2. Remove the top panel of the washer by unscrewing the screws holding it in place, typically located at the back.
3. Locate the main control board, which is usually housed in a plastic casing near the top of the machine.
4. Carefully disconnect all the wire harnesses attached to the old control board. It’s a good idea to take a photo beforehand for reference.
5. Remove the screws or release the clips holding the control board in its housing and take out the old board.
6. Install the new main control board, securing it with the screws or clips, and reconnect all the wire harnesses to their correct terminals.
7. Reattach the top panel, plug the washer back in, and run a test cycle to ensure the error is cleared and the machine functions properly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
When It’s Better to Replace Than Repair

Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
Here are a few signs it may be time to shop for a new one:
- ✓Appliance over 8-10 years old
- ✓Repair cost over 50% of replacement
- ✓Multiple recent breakdowns
- ✓Major component failure
Recommended Replacement Options
Budget Option

Top Rated Washers Under $600

Amazon’s Highest-Rated Value Models

Free ‘Room of Choice’ Delivery Available

Professional Haul-away Options at Checkout

View Top Rated Models & Delivery Options

Mid-Range Option

Top Rated Washers $600 to $1,000

Best-Sellers with Thousands of 5-Star Reviews

Expert Installation & Hookup Services available

Protection Plans for Long-Term Peace of Mind

View Top Rated Models & Delivery Options

Premium Option

Top Rated Washers Over $1,000

Top-of-the-Line Performance & Technology

White-Glove Delivery and Haul-away eligible

Comprehensive Warranty & Support Options

View Top Rated Models & Delivery Options
Why Upgrade via Amazon?

Fast, Scheduled Delivery – You pick the date and time

Expert Installation – Professional setup available for most models

Old Appliance Haul-away – They’ll take your broken unit when they leave

Easy Returns – Buy with confidence from a leader in customer service
As an Amazon Associate, we earn from qualifying purchases.
May 1, 2026
How to Fix Electrolux Washer Error B2
Error Code: B2 Difficulty: Hard

Problem: Supply voltage too high.

How to Fix B2 Error (Step-by-Step)
1. Disconnect the washer from the power source by unplugging it from the wall outlet. Also, turn off the water supply to the washer.
2. Remove the top panel of the washer. This is typically secured by screws at the back or sides of the machine.
3. Locate the main control board. It is usually housed in a plastic casing near the top of the washer.
4. Carefully disconnect all the wire harnesses connected to the old control board. It’s a good idea to take a photo of the connections before you start, for reference.
5. Remove the screws that hold the control board in place and carefully lift it out of the washer.
6. Install the new main control board, securing it with the screws you just removed.
7. Reconnect all the wire harnesses to the new board, using your photo as a guide to ensure they are in the correct positions.
8. Reattach the top panel of the washer and secure it with its screws.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
When It’s Better to Replace Than Repair

Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
Here are a few signs it may be time to shop for a new one:
- ✓Appliance over 8-10 years old
- ✓Repair cost over 50% of replacement
- ✓Multiple recent breakdowns
- ✓Major component failure
Recommended Replacement Options
Budget Option

Top Rated Washers Under $600

Amazon’s Highest-Rated Value Models

Free ‘Room of Choice’ Delivery Available

Professional Haul-away Options at Checkout

View Top Rated Models & Delivery Options

Mid-Range Option

Top Rated Washers $600 to $1,000

Best-Sellers with Thousands of 5-Star Reviews

Expert Installation & Hookup Services available

Protection Plans for Long-Term Peace of Mind

View Top Rated Models & Delivery Options

Premium Option

Top Rated Washers Over $1,000

Top-of-the-Line Performance & Technology

White-Glove Delivery and Haul-away eligible

Comprehensive Warranty & Support Options

View Top Rated Models & Delivery Options
Why Upgrade via Amazon?

Fast, Scheduled Delivery – You pick the date and time

Expert Installation – Professional setup available for most models

Old Appliance Haul-away – They’ll take your broken unit when they leave

Easy Returns – Buy with confidence from a leader in customer service
As an Amazon Associate, we earn from qualifying purchases.
May 1, 2026
How to Fix Electrolux Washer Error B1
Error Code: B1 Difficulty: Hard

Problem: Frequency of power out of limits.

How to Fix B1 Error (Step-by-Step)
1. UNPLUG THE WASHER. Safety first! Disconnect the washing machine from the wall outlet to prevent any electrical shock.
2. ACCESS THE CONTROL BOARD. The main control board is usually located inside the top panel. You will need to remove a few screws from the back of the top panel and slide it off.
3. DISCONNECT THE WIRES. Take a photo of the wire connections on the old control board before you disconnect anything. This will be your map for reconnecting them to the new board. Carefully unplug all the wire harnesses from the board.
4. REMOVE THE OLD BOARD. The control board is typically held in place by plastic mounting tabs or a few screws. Gently release the tabs or unscrew the screws to free the board and lift it out.
5. INSTALL THE NEW BOARD. Place the new control board into the same position as the old one, making sure it snaps securely into the mounting tabs or is fastened with the screws.
6. RECONNECT THE WIRES. Using the photo you took earlier as a guide, carefully plug all the wire harnesses back into their correct ports on the new control board.
7. REASSEMBLE AND TEST. Slide the top panel back into place and secure it with the screws. Plug the washer back in and run a test cycle to ensure everything is working correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
When It’s Better to Replace Than Repair

Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
Here are a few signs it may be time to shop for a new one:
- ✓Appliance over 8-10 years old
- ✓Repair cost over 50% of replacement
- ✓Multiple recent breakdowns
- ✓Major component failure
Recommended Replacement Options
Budget Option

Top Rated Washers Under $600

Amazon’s Highest-Rated Value Models

Free ‘Room of Choice’ Delivery Available

Professional Haul-away Options at Checkout

View Top Rated Models & Delivery Options

Mid-Range Option

Top Rated Washers $600 to $1,000

Best-Sellers with Thousands of 5-Star Reviews

Expert Installation & Hookup Services available

Protection Plans for Long-Term Peace of Mind

View Top Rated Models & Delivery Options

Premium Option

Top Rated Washers Over $1,000

Top-of-the-Line Performance & Technology

White-Glove Delivery and Haul-away eligible

Comprehensive Warranty & Support Options

View Top Rated Models & Delivery Options
Why Upgrade via Amazon?

Fast, Scheduled Delivery – You pick the date and time

Expert Installation – Professional setup available for most models

Old Appliance Haul-away – They’ll take your broken unit when they leave

Easy Returns – Buy with confidence from a leader in customer service
As an Amazon Associate, we earn from qualifying purchases.
May 1, 2026
How to Fix Electrolux Washer Error 9E
Error Code: 9E Difficulty: Moderate

Problem: Touch sensor on the user interface is not responding.

How to Fix 9E Error (Step-by-Step)
1. Disconnect the washer from the power source to ensure safety.
2. Remove the top panel of the washer by unscrewing the screws at the back.
3. Locate the user interface control board, which is typically situated at the front of the washer.
4. Carefully disconnect the wire connectors attached to the control board.
5. Remove the screws that are holding the control board in place and then remove the old board.
6. Install the new user interface control board (part 137007000) and secure it with the screws.
7. Reconnect all the wire connectors, reattach the top panel, and plug the washer back in to test the new interface.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
When It’s Better to Replace Than Repair

Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
Here are a few signs it may be time to shop for a new one:
- ✓Appliance over 8-10 years old
- ✓Repair cost over 50% of replacement
- ✓Multiple recent breakdowns
- ✓Major component failure
Recommended Replacement Options
Budget Option

Top Rated Washers Under $600

Amazon’s Highest-Rated Value Models

Free ‘Room of Choice’ Delivery Available

Professional Haul-away Options at Checkout

View Top Rated Models & Delivery Options

Mid-Range Option

Top Rated Washers $600 to $1,000

Best-Sellers with Thousands of 5-Star Reviews

Expert Installation & Hookup Services available

Protection Plans for Long-Term Peace of Mind

View Top Rated Models & Delivery Options

Premium Option

Top Rated Washers Over $1,000

Top-of-the-Line Performance & Technology

White-Glove Delivery and Haul-away eligible

Comprehensive Warranty & Support Options

View Top Rated Models & Delivery Options
Why Upgrade via Amazon?

Fast, Scheduled Delivery – You pick the date and time

Expert Installation – Professional setup available for most models

Old Appliance Haul-away – They’ll take your broken unit when they leave

Easy Returns – Buy with confidence from a leader in customer service
As an Amazon Associate, we earn from qualifying purchases.
May 1, 2026
How to Fix Electrolux Dryer Error DR
Error Code: DR Difficulty: Moderate

Problem: Door switch is not closed.

How to Fix DR Error (Step-by-Step)
1. Unplug the dryer from the electrical outlet for safety and confirm the error stays cleared during a full test cycle.
2. Open the dryer door and locate the door switch, which is usually a small plastic component with a button or lever near the door opening.
3. Check if anything is physically blocking the door from closing completely and engaging the switch.
4. Remove the screws holding the door switch in place. You may need to pry it out gently.
5. Disconnect the wire harness attached to the back of the switch.
6. Connect the new door switch to the wire harness and secure it in the original position with its screws.
7. Plug the dryer back in and test the door to ensure the dryer starts.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error DP
Error Code: DP Difficulty: Easy

Problem: Drain pump activated.

How to Fix DP Error (Step-by-Step)
1. For condenser or heat pump dryers, locate the water collection tank, which is usually at the top left of the unit.
2. Carefully slide the water tank out of its housing and confirm the error stays cleared during a full test cycle.
3. Carry the tank to a sink and empty all the water out.
4. Slide the empty tank firmly back into its slot until it clicks into place.
5. If your model drains directly into a standpipe, check the drain hose for any kinks or clogs that would prevent water from draining properly.
6. Ensure the end of the drain hose is not pushed too far into the standpipe, which can create a siphon effect and prevent proper drainage.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error UO
Error Code: UO Difficulty: Easy

Problem: Vent open.

How to Fix UO Error (Step-by-Step)
1. Check the back of the dryer to ensure the vent hose is securely attached to the dryer’s exhaust port.
2. Follow the vent hose to the wall and confirm it is also securely attached to the wall duct opening.
3. Straighten out any sharp kinks or bends in the flexible vent hose that could be restricting airflow.
4. Disconnect the hose from both the dryer and the wall and look through it to check for any lint blockages.
5. Clean any accumulated lint from both the dryer’s exhaust port and the wall duct opening before reattaching the hose.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error UF
Error Code: UF Difficulty: Hard

Problem: Fan not running.

How to Fix UF Error (Step-by-Step)
1. Disconnect the dryer from its power source and confirm the error stays cleared during a full test cycle.
2. Depending on your model, remove either the front or rear panel to access the blower wheel housing.
3. Locate the blower wheel, which looks like a hamster wheel. Check for any lint, socks, or other debris that may be jamming it and preventing it from turning.
4. Inspect the drive belt. If it is broken, frayed, or has come off the motor pulley, it will need to be replaced.
5. If the blower wheel is clear and the belt is intact, the issue may be the drive motor itself. A seized or failed motor will need to be replaced by a professional.
6. Check the wiring between the motor and the main control board for any loose or burnt connections.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 134994700
- 809160304
- 5304508449
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error HF
Error Code: HF Difficulty: Hard

Problem: Line safe sensing circuit failure (main board failure).

How to Fix HF Error (Step-by-Step)
1. Ensure the dryer is completely disconnected from the power supply by unplugging the power cord.
2. Remove the top panel of the dryer to gain access to the internal electronics.
3. Identify the main control board, usually found near the top front of the unit.
4. Photograph the existing wire connections to the board to ensure correct reassembly.
5. Systematically unplug each wire connector from the old board. Be gentle and press any release tabs on the connectors.
6. Unscrew the mounting screws that hold the control board in its housing and carefully remove it.
7. Place the new main control board into the housing, secure it with the screws, and reconnect all the wires exactly as they were on the old board.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026
How to Fix Electrolux Dryer Error HE
Error Code: HE Difficulty: Hard

Problem: Heating Error – Dryer isn’t heating as it should.

How to Fix HE Error (Step-by-Step)
1. Unplug the dryer from the power outlet and confirm the error stays cleared during a full test cycle.
2. Check your home’s circuit breaker box to ensure the breaker dedicated to the dryer is not tripped. Electric dryers use two breakers; ensure both are on.
3. Disconnect the vent hose from the back of the dryer and check for any lint buildup or obstructions that could restrict airflow.
4. Remove the rear access panel. Locate the heating element and disconnect its wires. Use a multimeter to test for continuity between the terminals. If there is no continuity, the element is faulty and needs to be replaced.
5. Find the thermistor/thermostat on the blower housing or heating element housing. Disconnect the wires and test for continuity. An infinite resistance reading indicates a faulty part that needs replacement.
6. If the heating components test correctly, the problem could be a faulty connection or a failed main control board.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 134792700
- 137249910
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
May 1, 2026