Category: Electrolux

  • How to Fix Electrolux Refrigerator Error SH

    How to Fix Electrolux Refrigerator Error SH

    Error Code: SH Difficulty: Moderate

    Problem: Refrigerator temperature sensor has shorted.

    How to Fix SH Error (Step-by-Step)

    1. First, unplug the refrigerator from the wall outlet for safety.
    2. Locate the temperature sensor inside the refrigerator compartment, usually near the top and back.
    3. Disconnect the wire harness from the old sensor and confirm the error stays cleared during a full test cycle.
    4. Remove any screws or clips holding the sensor in place and take it out.
    5. Install the new temperature sensor and secure it with the original screws or clips.
    6. Reconnect the wire harness and plug the refrigerator back in.
    7. Allow the refrigerator several hours to stabilize its temperature and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 240597203
    • 297018400
    • 50285419003

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error SB OR SB

    How to Fix Electrolux Refrigerator Error SB OR SB

    Error Code: SB OR SB Difficulty: Easy

    Problem: Sabbath Mode is active.

    How to Fix SB OR SB Error (Step-by-Step)

    1. To deactivate Sabbath Mode, locate and press the ‘Options’ button on your control panel.
    2. Scroll through the options until you find ‘Sabbath Mode’ or a similar indicator.
    3. Press and hold the ‘Set’ or ‘Confirm’ button for three to five seconds.
    4. The display should indicate that Sabbath Mode is now off.
    5. The interior lights and dispenser functions should now be restored.
    6. If you have trouble, unplug the refrigerator for five minutes and then plug it back in to reset the controls.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error PF

    How to Fix Electrolux Refrigerator Error PF

    Error Code: PF Difficulty: Easy

    Problem: Power Failure. Indicates the refrigerator has lost and regained power.

    How to Fix PF Error (Step-by-Step)

    1. Press any key on the refrigerator’s control panel to clear the code.
    2. Check that the refrigerator is securely plugged into a working outlet.
    3. Verify that the circuit breaker for the kitchen has not tripped.
    4. If the power in your home is out, wait for it to be restored.
    5. Once power is stable, the refrigerator will resume normal operation.
    6. If the code reappears frequently, consider using a surge protector to shield the appliance from power fluctuations.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error NS

    How to Fix Electrolux Refrigerator Error NS

    Error Code: NS Difficulty: Easy

    Problem: In diagnostic mode, indicates no PWM signal is detected for a fan motor when it is off.

    How to Fix NS Error (Step-by-Step)

    1. This code indicates a normal condition where the fan motor is off.
    2. No action is required as this is part of the refrigerator’s standard check reporting.
    3. The code should clear on its own during the next fan cycle.
    4. If the code persists and is accompanied by cooling problems, then further checks may be needed.
    5. For now, continue to use your refrigerator as usual and confirm the error stays cleared during a full test cycle.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error NP

    How to Fix Electrolux Refrigerator Error NP

    Error Code: NP Difficulty: Easy

    Problem: In diagnostic mode, indicates the absence of a 12V or GND signal for a fan motor when it is on.

    How to Fix NP Error (Step-by-Step)

    1. This code appears when the refrigerator is in a special check or service mode and does not indicate a part failure in normal use.
    2. To exit the check mode, the simplest method is to perform a power cycle.
    3. Unplug the refrigerator from the electrical outlet and confirm the error stays cleared during a full test cycle.
    4. Wait for 5 minutes. This allows the internal computer to fully reset and exit any special modes.
    5. Plug the refrigerator back into the outlet and confirm the error stays cleared during a full test cycle.
    6. The unit will restart in its normal operating mode, and the ‘NP’ code will no longer be displayed.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error H OR HI

    How to Fix Electrolux Refrigerator Error H OR HI

    Error Code: H OR HI Difficulty: Easy

    Problem: High temperature alert. The temperature inside the refrigerator or freezer is too high.

    How to Fix H OR HI Error (Step-by-Step)

    1. First, confirm that all refrigerator and freezer doors are fully closed and were not accidentally left open.
    2. Check the temperature settings on the control panel. Ensure they are set to the recommended levels, typically 0°F for the freezer and 37°F for the refrigerator.
    3. Inspect the air vents inside both compartments. Make sure they are not blocked by food packages, allowing for proper cold air circulation.
    4. If you have recently loaded a large amount of warm groceries, allow the refrigerator at least 4 to 6 hours to cool down and reach the set temperature.
    5. You can press the ‘Alarm Reset’ or ‘Mute’ button to silence the warning beep while the unit is cooling.
    6. The ‘H’ or ‘HI’ indicator will automatically turn off once the interior temperature returns to a safe level.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error ER T1 – ER T6

    How to Fix Electrolux Refrigerator Error ER T1 – ER T6

    Error Code: ER T1 – ER T6 Difficulty: Moderate

    Problem: Temperature sensor error.

    How to Fix ER T1 – ER T6 Error (Step-by-Step)

    1. First, unplug the refrigerator from the wall outlet to disconnect all power.
    2. Empty the contents of the affected compartment (refrigerator or freezer) and remove any shelves needed to access the interior back or side panel.
    3. The temperature sensor is usually located behind a small plastic cover. Unscrew or unclip this cover to expose the sensor.
    4. The sensor is a small plastic probe with a wire attached. Carefully disconnect the wire harness that connects the old sensor to the refrigerator.
    5. Connect the new temperature sensor (Part No. 240597203) to the wire harness.
    6. Snap the new sensor into its designated clip or housing and re-attach the protective cover.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error ER CE

    How to Fix Electrolux Refrigerator Error ER CE

    Error Code: ER CE Difficulty: Hard

    Problem: Communication error.

    How to Fix ER CE Error (Step-by-Step)

    1. Begin by performing a system reset. Unplug the refrigerator from its power outlet and wait for 10 minutes to allow the internal electronics to discharge.
    2. Plug the refrigerator back in. Wait a few minutes to see if the control boards re-establish communication and the error clears on its own.
    3. If the error returns, unplug the unit again. Carefully inspect the wiring that runs to the user interface display, especially around the top door hinge area, for any pinched or broken wires.
    4. Locate the main control board on the back of the refrigerator behind an access panel. Remove the panel.
    5. Check all wire harness connections to the main board (Part No. 5304499075 or 5304527931), ensuring they are all plugged in securely.
    6. If connections are secure and the error remains, it indicates a failure of the main board or the display board (Part No. 5304498781), which will require replacement.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304499075
    • 5304527931

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error E42

    How to Fix Electrolux Refrigerator Error E42

    Error Code: E42 Difficulty: Hard

    Problem: Door lock device failure.

    How to Fix E42 Error (Step-by-Step)

    1. Disconnect the refrigerator from the wall outlet to ensure your safety by cutting off all electrical power.
    2. Locate the door lock assembly, which is typically found on the refrigerator body where the door latches shut.
    3. Remove any plastic covers that may be hiding the lock mechanism and its mounting screws.
    4. Unscrew the two screws holding the faulty lock in place.
    5. Gently pull the lock out and carefully disconnect the single wire harness attached to it.
    6. Connect the wire harness to the new door lock (Part No. 5304449038) and position the new lock.
    7. Secure the new lock with the mounting screws and replace the cover. Restore power and test the door.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Refrigerator Error DOOR AJAR

    How to Fix Electrolux Refrigerator Error DOOR AJAR

    Error Code: DOOR AJAR Difficulty: Easy

    Problem: A door has been open for 5 minutes or more.

    How to Fix DOOR AJAR Error (Step-by-Step)

    1. Firmly close all refrigerator and freezer doors to ensure they are not physically open.
    2. Carefully inspect the rubber door gaskets (seals) on all doors for any food debris, stickiness, or obstructions.
    3. Clean the entire surface of the door gaskets using a soft cloth with warm, soapy water, then dry them completely.
    4. Check inside the refrigerator and freezer for any items, such as large bottles or food containers, that might be preventing the door from sealing properly.
    5. Ensure all interior drawers and crispers are fully closed and not blocking the door.
    6. If the alarm persists with the doors confirmed shut, unplug the refrigerator for 5 minutes to reset the electronics, then plug it back in.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes