Category: Washer

  • How to Fix Amana Washer Error FD

    How to Fix Amana Washer Error FD

    Error Code: FD Difficulty: Easy

    Problem: Internal Board Problem – Drive Motor

    How to Fix FD Error (Step-by-Step)

    1. Unplug the washing machine from the electrical outlet and confirm the error stays cleared during a full test cycle.
    2. Wait for at least 5 minutes. This allows the internal electronic components and control board to fully discharge and reset.
    3. While waiting, ensure the washer door is securely closed and there are no items obstructing the lock.
    4. Plug the washer back into the power outlet and confirm the error stays cleared during a full test cycle.
    5. Select a new wash cycle and press ‘Start’ to see if the reset has cleared the internal board problem.
    6. If the code reappears, there may be a more serious issue with the drive motor or control board that requires professional service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error FILL OR SENSING LIGHT ON

    How to Fix Amana Washer Error FILL OR SENSING LIGHT ON

    Error Code: FILL OR SENSING LIGHT ON Difficulty: Moderate

    Problem: Filling or Sensing

    How to Fix FILL OR SENSING LIGHT ON Error (Step-by-Step)

    1. Unplug the washer from the wall outlet to ensure safety.
    2. Turn off both the hot and cold water supply valves connected to the washer.
    3. Open the washer lid and check that the lid switch, a small plastic piece on the body that meets the lid, is not broken or obstructed.
    4. Carefully pull the washer away from the wall to access the back panel.
    5. Unscrew the mounting screws holding the top control panel in place and flip it back to access the lid switch and water valve connections.
    6. Inspect the wire harness connecting to the lid switch and the water inlet valve for any loose or damaged wires.
    7. If the wiring is secure and the lid switch appears damaged, it will need to be replaced to allow the washer to sense the lid is closed and begin the fill cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10838613 (Lid Switch)
    • WP8318084 (Lid Switch)
    • 205613 (Water Inlet Valve)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error HC

    How to Fix Amana Washer Error HC

    Error Code: HC Difficulty: Easy

    Problem: Hot and Cold Hoses are Reversed

    How to Fix HC Error (Step-by-Step)

    1. Turn off the hot and cold water faucets connected to the back of the washer.
    2. Use a pair of pliers to unscrew the metal fittings on both hoses from the washer’s water inlet valve.
    3. Look for the ‘H’ (Hot) and ‘C’ (Cold) labels on the washer’s inlet valve ports.
    4. Reconnect the hose coming from your home’s hot water supply to the ‘H’ port.
    5. Reconnect the hose from your cold water supply to the ‘C’ port.
    6. Tighten both hose connections by hand first, then give them a final quarter-turn with pliers to prevent leaks.
    7. Turn the water faucets back on fully and check for any drips before pushing the washer back into place.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error INT

    How to Fix Amana Washer Error INT

    Error Code: INT Difficulty: Easy

    Problem: Cycle Paused or Canceled

    How to Fix INT Error (Step-by-Step)

    1. Look at the control panel to see if the ‘Start/Pause’ button has been pressed, which can pause the cycle.
    2. Press the ‘Start/Pause’ button once to resume the current wash cycle.
    3. If you intended to stop the cycle completely, press and hold the ‘Cancel’ or ‘Power’ button for about three seconds.
    4. The washer will begin to drain any water in the tub, which may take a few minutes.
    5. The lid will unlock once the water has been drained.
    6. You can now select a new cycle and press ‘Start’ to begin a new wash.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LC

    How to Fix Amana Washer Error LC

    Error Code: LC Difficulty: Easy

    Problem: Control Lock Activated

    How to Fix LC Error (Step-by-Step)

    1. Locate the ‘Control Lock’ button on the washer’s control panel. It may be labeled or indicated by a small padlock icon.
    2. Press and hold the ‘Control Lock’ button for 3 to 5 seconds.
    3. The indicator light for the control lock feature should turn off.
    4. The washer’s controls are now unlocked, and you can select a cycle and start a load of laundry.
    5. To reactivate the lock and prevent accidental button presses, simply press and hold the same button again for 3 to 5 seconds until the light comes on.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LF

    How to Fix Amana Washer Error LF

    Error Code: LF Difficulty: Moderate

    Problem: Long Fill

    How to Fix LF Error (Step-by-Step)

    1. Unplug the washing machine from the power source for safety.
    2. Shut off the hot and cold water supply valves at the wall.
    3. Unscrew the water inlet hoses from the back of the washer. Have a small bucket or towel ready to catch any residual water.
    4. Look inside the two water inlet ports on the washer. You will see small filter screens.
    5. Carefully remove the screens with a pair of needle-nose pliers.
    6. Clean any sediment or debris from the screens using a small brush and water.
    7. Reinstall the clean filter screens, reconnect the water hoses securely, and turn the water supply back on before plugging the washer in again.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W11210459 (Water Inlet Valve)
    • WPW10144820 (Water Inlet Valve)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LO FL

    How to Fix Amana Washer Error LO FL

    Error Code: LO FL Difficulty: Moderate

    Problem: Low Flow of Water

    How to Fix LO FL Error (Step-by-Step)

    1. First, ensure that both the hot and cold water supply valves connected to the washer are turned on completely.
    2. Unplug the washer from the electrical outlet and confirm the error stays cleared during a full test cycle.
    3. Unscrew the water inlet hoses from the back of the machine and check for any kinks or twists that could restrict water flow.
    4. Inspect the small filter screens located inside the water inlet ports on the washer itself. Debris can build up here.
    5. Gently pull the screens out with pliers and clean them thoroughly with a small brush under running water.
    6. Reinsert the screens, reattach the hoses securely, and ensure they are not kinked.
    7. Plug the washer back in and turn the water supply on to test the flow.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W11210459 (Water Inlet Valve)
    • WPW10144820 (Water Inlet Valve)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LOC

    How to Fix Amana Washer Error LOC

    Error Code: LOC Difficulty: Easy

    Problem: Control Lock Activated

    How to Fix LOC Error (Step-by-Step)

    1. Find the button on your Amana washer’s control panel that is designated for the ‘Control Lock’ function, often marked with a padlock symbol.
    2. Press and hold this specific button for approximately 3 to 5 seconds.
    3. You should see the ‘Control Lock’ indicator light on the display turn off.
    4. This indicates that the control panel is now unlocked and fully functional.
    5. You can now operate the washer as usual by selecting your desired cycle and settings.
    6. To re-enable the lock, repeat the process by holding the same button for another 3-5 seconds.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LD

    How to Fix Amana Washer Error LD

    Error Code: LD Difficulty: Hard

    Problem: Long Drain Time

    How to Fix LD Error (Step-by-Step)

    1. Unplug the washer from the power outlet to prevent any electrical accidents.
    2. Place towels and a shallow pan around the base of the washer to catch water.
    3. Carefully tilt the washer forward, resting it securely against a wall to access the drain pump, usually located at the bottom rear.
    4. Squeeze the clamp on the drain hose connected to the pump and slide it off, directing the hose into the pan to drain remaining water.
    5. Inspect the pump inlet and the drain hose for any obstructions like socks, lint, or other small items and remove them.
    6. If the hose is clear and the pump impeller doesn’t turn freely, the drain pump motor is likely faulty.
    7. To replace it, disconnect the wire harness, remove the mounting screws, install the new pump, and reconnect all hoses and wires before carefully setting the washer upright.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LDL

    How to Fix Amana Washer Error LDL

    Error Code: LDL Difficulty: Moderate

    Problem: Lid Lock Failure

    How to Fix LDL Error (Step-by-Step)

    1. Unplug the washer from the wall outlet to ensure your safety.
    2. Locate the lid lock assembly. It is typically found beneath the main top of the washer, near the opening where the lid closes.
    3. To access the lock, you will likely need to raise the main top. Look for and remove the screws at the back or sides of the washer top panel.
    4. Carefully disconnect the wire harness that plugs into the lid lock assembly. There is usually a small clip you need to press to release it.
    5. Remove the screws holding the old lid lock in place and take the old assembly out.
    6. Position the new lid lock assembly (part W11307244, W10810403, or W11253733) and secure it with the screws.
    7. Reconnect the wire harness, lower the main top back into position, and replace its screws.
    8. Plug the washer back in and start a cycle to confirm the new lock works correctly.

    Verified Compatible Alternatives:

    • W11253733 (Lid Lock Assembly)
    • W11307244 (Lid Lock Assembly)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.