Category: Washer

  • How to Fix Amana Washer Error UL

    How to Fix Amana Washer Error UL

    Error Code: UL Difficulty: Hard

    Problem: Unbalanced Load

    How to Fix UL Error (Step-by-Step)

    1. Unplug the washer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Open the washer lid and redistribute the clothes evenly around the wash plate. Avoid washing single, heavy items by themselves.
    3. Close the lid and plug the washer back in. Try running a spin cycle. If the error persists, proceed to the next step.
    4. To inspect the suspension, you will need to lift the top panel of the washer. Use a putty knife to release the two clips on the front edge.
    5. With the top panel lifted, you can see the four suspension rods, one at each corner of the tub. Check if any of the rods appear broken or disconnected. Gently press down on the tub to see if it bounces excessively, which indicates weak suspension.
    6. To replace a suspension rod, lift the rod up from the tub bracket, then disconnect it from the top support cup. Install the new rod by reversing these steps.
    7. If the suspension rods are intact, the issue may be with the drive hub or gearcase, which typically requires a professional service.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10780048
    • W10821956
    • W11130362

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error RL

    How to Fix Amana Washer Error RL

    Error Code: RL Difficulty: Easy

    Problem: Items detected in the washer during the Clean Washer cycle.

    How to Fix RL Error (Step-by-Step)

    1. Press the ‘Pause’ or ‘Cancel’ button to stop the ‘Clean Washer’ cycle.
    2. Wait for the washer lid to unlock and confirm the error stays cleared during a full test cycle.
    3. Open the lid and remove any clothing or other items that were left inside the washer tub.
    4. Close the lid securely and confirm the error stays cleared during a full test cycle.
    5. Select the ‘Clean Washer’ cycle again and confirm the error stays cleared during a full test cycle.
    6. Press the ‘Start’ button to begin the cycle without any items in the tub.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error OL

    How to Fix Amana Washer Error OL

    Error Code: OL Difficulty: Easy

    Problem: Overload

    How to Fix OL Error (Step-by-Step)

    1. Press the ‘Cancel’ or ‘Power’ button to stop the washer.
    2. Open the washer door and look at the load. Items should be loosely packed and not crammed in.
    3. Remove several items to reduce the size of the load. A washer drum should not be filled more than three-quarters full.
    4. Redistribute the remaining items evenly around the wash plate or agitator to improve balance.
    5. Close the door and restart the cycle and confirm the error stays cleared during a full test cycle.
    6. For future loads, wash bulky items like comforters or blankets in smaller, separate loads.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error DRN

    How to Fix Amana Washer Error DRN

    Error Code: DRN Difficulty: Moderate

    Problem: Drain Error

    How to Fix DRN Error (Step-by-Step)

    1. First, check the drain hose at the back of the washer. Ensure it is not kinked, bent, or clogged.
    2. Make sure the drain hose is not inserted too far into the standpipe; it should only be about 4-5 inches in.
    3. Unplug the washer. You will need to access the drain pump, which is usually located behind a removable front panel at the bottom of the machine.
    4. Place a shallow pan and towels under the pump area to catch residual water. Slowly unscrew the pump’s filter cap to drain the remaining water.
    5. Clean the filter of any debris, such as lint, coins, or small clothing items.
    6. If the filter is clear and the hose is not blocked, the drain pump itself may have failed and will need to be replaced.
    7. To replace the pump, disconnect the hoses and the wire connector, remove the mounting screws, and install the new pump.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10276397
    • W10730972
    • WPW10730972

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error DU

    How to Fix Amana Washer Error DU

    Error Code: DU Difficulty: Easy

    Problem: Door Unlock Failure

    How to Fix DU Error (Step-by-Step)

    1. Press the ‘Cancel’ or ‘Power’ button to end the current cycle.
    2. Wait for 3-5 minutes. The washer’s control board needs time to process the cancel command and disengage the lock.
    3. If the door remains locked, unplug the washer from the wall outlet.
    4. Let the washer sit without power for at least 5 minutes.
    5. Plug the washer back in. The door should unlock after the machine powers on.
    6. Check for any small items that could be preventing the lock from disengaging properly.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error DLO

    How to Fix Amana Washer Error DLO

    Error Code: DLO Difficulty: Hard

    Problem: Lid is not locking. This could be due to an obstruction or detergent buildup.

    How to Fix DLO Error (Step-by-Step)

    1. First, check for any clothing items, towels, or other obstructions that might be caught between the lid and the washer body, preventing it from closing properly.
    2. Unplug the washer from the power source and confirm the error stays cleared during a full test cycle.
    3. Clean the area around the lid lock and the strike with a damp cloth to remove any detergent or fabric softener buildup.
    4. Inspect the lid lock mechanism for any visible damage or signs of wear.
    5. If the area is clear and clean and the lock still won’t engage, the lid lock assembly likely needs to be replaced.
    6. To replace the lock, you will need to access it by removing the top console or panel of the washer. Disconnect the wire harness, remove the screws holding the old lock, and install the new one.
    7. Reassemble the washer, plug it in, and test the new lock by starting a cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10838613
    • W11253733
    • W11307244

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error DL

    How to Fix Amana Washer Error DL

    Error Code: DL Difficulty: Hard

    Problem: Door Lock Failure

    How to Fix DL Error (Step-by-Step)

    1. Unplug the washer from the electrical outlet to ensure safety.
    2. Wait at least 2-3 minutes to allow all electrical charge to dissipate.
    3. The door lock assembly is typically located behind the front panel of the washer, near the door opening. You may need to remove the top panel and/or the front panel to access it.
    4. Carefully inspect the wiring connecting to the door lock assembly. Look for any loose or damaged wires.
    5. If the wiring appears secure, the lock assembly itself is likely faulty and needs to be replaced.
    6. Disconnect the wiring harness from the old lock, remove the mounting screws, and install the new lock assembly in its place.
    7. Reassemble the washer panels, plug the machine back in, and test the door lock.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10838613
    • W11253733
    • W11307244

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error DET

    How to Fix Amana Washer Error DET

    Error Code: DET Difficulty: Easy

    Problem: Detergent cartridge not detected in the dispenser.

    How to Fix DET Error (Step-by-Step)

    1. Open the detergent dispenser drawer and confirm the error stays cleared during a full test cycle.
    2. Check to ensure the detergent cartridge is properly seated in its compartment.
    3. Remove the cartridge and inspect it for any clogs or blockages.
    4. Re-insert the cartridge firmly into the dispenser until you hear a click.
    5. Close the dispenser drawer and try starting the cycle again.
    6. If the issue persists, ensure you are using the correct type of detergent cartridge for your model.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error WASH LIGHT ON OR FLASHING

    How to Fix Amana Washer Error WASH LIGHT ON OR FLASHING

    Error Code: WASH LIGHT ON OR FLASHING Difficulty: Easy

    Problem: Washing

    How to Fix WASH LIGHT ON OR FLASHING Error (Step-by-Step)

    1. Do not be alarmed, this is not an error code. This light simply indicates that the washer is currently in the middle of a wash cycle.
    2. Allow the cycle to complete normally and confirm the error stays cleared during a full test cycle.
    3. The light will turn off once the washing cycle has finished.
    4. If you need to stop the cycle, press the ‘Cancel’ or ‘Power’ button.
    5. Wait for the machine to drain completely before attempting to open the door.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error SUD

    How to Fix Amana Washer Error SUD

    Error Code: SUD Difficulty: Easy

    Problem: Suds Detected

    How to Fix SUD Error (Step-by-Step)

    1. Do not add any more detergent. The washer will automatically attempt to resolve the suds issue.
    2. The machine will pause the cycle and may add extra rinses to clear the suds. This will extend the cycle time.
    3. Run a rinse and spin cycle to help clear the remaining suds.
    4. In the future, use only HE (High-Efficiency) detergent as recommended for your washer.
    5. Measure detergent carefully according to the load size and soil level to prevent over-sudsing.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes