Category: Amana

Error Code: DETERGENT LOW Difficulty: Easy

Problem: The detergent level in the bulk dispenser is low and needs to be refilled.

How to Fix DETERGENT LOW Error (Step-by-Step)

1. Acknowledge this message as a simple reminder that the bulk detergent dispenser needs to be refilled soon.
2. Locate and pull out the bulk dispenser drawer, which is usually on the top-left side of the washer.
3. Identify the compartment for liquid detergent and confirm the error stays cleared during a full test cycle.
4. Carefully pour High-Efficiency (HE) liquid detergent into the compartment and confirm the error stays cleared during a full test cycle.
5. Be sure not to fill past the ‘Max Fill’ line indicated inside the dispenser.
6. Close the dispenser drawer securely. The message should now be gone.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: CYCLE COMPLETE LIGHT ON Difficulty: Easy

Problem: Cycle Finished

How to Fix CYCLE COMPLETE LIGHT ON Error (Step-by-Step)

1. Understand that this light is an indicator that the selected wash cycle has finished successfully.
2. The washer door will be unlocked, allowing you to open it.
3. Open the door and remove your clean laundry promptly to prevent mildew.
4. To help the washer drum air out and stay fresh, leave the door slightly ajar.
5. Press the ‘Power’ button to turn the machine off and clear the light.
6. The light will also typically turn off on its own after a set period of time.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: CL Difficulty: Easy

Problem: Control Lock Activated

How to Fix CL Error (Step-by-Step)

1. Recognize that ‘CL’ on the display means the Control Lock or Child Lock feature is activated, which disables the buttons.
2. Look for a button on the control panel specifically labeled ‘Control Lock’ or with a small lock icon next to it.
3. Press and hold this specific button for three full seconds.
4. For some models, you may need to press and hold a specific combination of two buttons simultaneously for three seconds. Check the button labels for text like ‘Hold 3 Sec to Lock’.
5. The ‘CL’ code will disappear from the display once the controls are unlocked.
6. You can now operate the washer normally and confirm the error stays cleared during a full test cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: ADD GARMENT LIGHT ON Difficulty: Easy

Problem: Add Garment

How to Fix ADD GARMENT LIGHT ON Error (Step-by-Step)

1. Notice that the ‘Add Garment’ light means it is still early enough in the wash cycle to add more items.
2. Press the ‘Start/Pause’ button one time to pause the washer.
3. Wait a few moments for the washer door to unlock; you will typically hear a click.
4. Open the door and add any forgotten items of clothing.
5. Close the door firmly until it latches and confirm the error stays cleared during a full test cycle.
6. Press the ‘Start/Pause’ button again to resume the wash cycle.
7. Be aware that this light will turn off later in the cycle when it is no longer possible to add clothes.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: 5D Difficulty: Easy

Problem: Suds detection. This is an alternate code for ‘Sd’ or ‘Sud’.

How to Fix 5D Error (Step-by-Step)

1. Understand that ‘5D’, ‘Sd’, or ‘Sud’ means the washer has detected too many suds and is working to correct it.
2. Allow the washer to complete its automatic process of adding a rinse and a short spin to reduce the suds. Do not interrupt the cycle.
3. Wait for the cycle to finish, which may take longer than usual.
4. After the cycle is complete, remove the laundry and confirm the error stays cleared during a full test cycle.
5. Run an empty ‘Clean Washer’ or ‘Normal’ cycle with hot water to flush out any residual detergent.
6. In the future, ensure you are using only High-Efficiency (HE) detergent.
7. Reduce the amount of detergent used, especially for smaller or lightly soiled loads, to prevent this from happening again.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: 1H, 2H, 3H…UP TO 12H Difficulty: Easy

Problem: Delay Start Timer

How to Fix 1H, 2H, 3H…UP TO 12H Error (Step-by-Step)

1. Recognize that this code indicates the ‘Delay Start’ feature is active and is not an error.
2. The number shown (1H, 2H, etc.) represents the remaining hours until the wash cycle begins.
3. To cancel the delay, press the ‘Power’ button to turn the washer off.
4. Press the ‘Power’ button again to turn the washer back on.
5. Select your desired wash cycle and options as you normally would.
6. Press the ‘Start’ button to begin the cycle immediately without a delay.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: CL Difficulty: Easy

Problem: Control Lock Activated

How to Fix CL Error (Step-by-Step)

1. Identify that the ‘CL’ code means the Control Lock (or Child Lock) feature is currently active, preventing any button inputs.
2. To deactivate the lock, you must press and hold a specific button or combination of buttons.
3. Look for a button on the control panel that has a small lock icon next to it, such as ‘Cycle Signal’ or ‘Extra Rinse’.
4. Press and hold this specific button for 3 to 5 seconds.
5. Watch the display screen for the ‘CL’ code to disappear.
6. Once the code is gone, the controls are unlocked, and you can now operate the washer normally.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: ERR Difficulty: Easy

Problem: General Error

How to Fix ERR Error (Step-by-Step)

1. Recognize ‘ERR’ as a general electronic error, often caused by a temporary communication glitch in the control board.
2. First, try to clear the code by pressing the ‘Cancel’ or ‘Power’ button to end the current cycle attempt.
3. Unplug the washing machine’s power cord directly from the wall outlet.
4. Leave the washer completely without power for at least 5 minutes. This allows the internal electronics to fully discharge and reset.
5. Plug the power cord securely back into the wall outlet.
6. Power the machine on and attempt to start a new cycle to confirm the error is cleared.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: F20 Difficulty: Easy

Problem: No Water Detected

How to Fix F20 Error (Step-by-Step)

1. Check that the hot and cold water faucets connected to the washer are turned on fully.
2. Unplug the washer from the power outlet and confirm the error stays cleared during a full test cycle.
3. Turn off the water faucets and disconnect the inlet hoses from the back of the washer.
4. Check the small filter screens inside the hose connections on the washer. Use a small brush or pliers to gently remove any sediment or debris.
5. Check the hoses themselves for any kinks or twists that could be blocking water flow. Straighten them if necessary.
6. Reconnect the hoses securely, turn the water faucets back on, and plug the washer in.
7. Start a new cycle to confirm water is now entering the machine.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Error Code: F21 Difficulty: Moderate

Problem: Long Drain

How to Fix F21 Error (Step-by-Step)

1. First, check the drain hose at the back of the washer. Make sure it is not kinked, clogged, or inserted too far into the standpipe (no more than 6-8 inches).
2. If the hose is clear, unplug the washer from power.
3. You will need to drain the remaining water from the tub. Place a shallow pan and towels on the floor and disconnect the drain hose from the standpipe to let the water drain out.
4. To access the drain pump, you may need to tilt the machine or remove the front or back panel.
5. Locate the drain pump at the bottom of the washer. Disconnect the hoses attached to it (be prepared for more water) and the electrical connector.
6. Remove the screws or clips holding the old pump, and install the new one.
7. Reconnect the hoses and electrical wire, reassemble the washer, and run a drain/spin cycle to test.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.