Category: Amana

  • How to Fix Amana Dishwasher Error 10-1

    How to Fix Amana Dishwasher Error 10-1

    Error Code: 10-1 Difficulty: Hard

    Problem: Dispenser electrical problem.

    How to Fix 10-1 Error (Step-by-Step)

    1. Turn Off Power: For your safety, disconnect the dishwasher from its power source by turning off the corresponding circuit breaker.
    2. Remove Inner Door Panel: Open the dishwasher door and unscrew the series of screws around the perimeter of the inner door panel. Lift the inner panel away to access the dispenser.
    3. Disconnect Old Dispenser: Take a photo of the wiring connected to the dispenser. Carefully unplug the wire harness. Release the clips or remove the screws holding the old dispenser assembly to the door panel.
    4. Remove and Clean: Push the old dispenser out from the front of the door. Clean any residue from the dispenser opening on the door panel.
    5. Install New Dispenser: From the front of the door, insert the new dispenser assembly into the opening and ensure it sits flush. Secure it in place with its clips or screws from the inside. Reconnect the wire harness.
    6. Reassemble and Test: Place the inner door panel back on and secure it with the screws. Turn the power back on and run a wash cycle to check if the new dispenser is operating correctly.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • WPW10224430
    • WPW10428214

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.

      Search Amazon for Whirlpool dishwasher drain pump

    • Whirlpool dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.

      Search Amazon for Whirlpool dishwasher water inlet valve

    • Whirlpool dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating error-code or control faults after wiring and latch checks.

      Search Amazon for Whirlpool dishwasher control board

    Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.


    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error TEMPERATURE ALARM

    How to Fix Amana Refrigerator Error TEMPERATURE ALARM

    Error Code: TEMPERATURE ALARM Difficulty: Easy

    Problem: Indicates that the internal temperature of the refrigerator or freezer has exceeded a safe level.

    How to Fix TEMPERATURE ALARM Error (Step-by-Step)

    1. Press the ‘Alarm Off’ button to silence the audible alert.
    2. Check that the doors for both the refrigerator and freezer are completely closed. Nudge them shut firmly.
    3. Inspect the rubber door seals (gaskets) for any gaps, dirt, or stickiness that could prevent a tight seal. Clean them with warm, soapy water.
    4. Look for any items inside, like a large pizza box or food container, that might be physically blocking the door from closing all the way.
    5. Review your temperature settings to ensure they are set to the recommended levels (e.g., 37°F for the fridge, 0°F for the freezer).
    6. If you have recently loaded a large amount of groceries, allow the refrigerator at least 24 hours to cool down and stabilize the internal temperature.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error THERMISTOR ALARM

    How to Fix Amana Refrigerator Error THERMISTOR ALARM

    Error Code: THERMISTOR ALARM Difficulty: Moderate

    Problem: Either the freezer or refrigerator thermistor circuit is open. The freezer or refrigerator indicator light shows and temperature indicators 4 through 7 turn on in sequence.

    How to Fix THERMISTOR ALARM Error (Step-by-Step)

    1. Disconnect the refrigerator from its power source by unplugging it from the wall.
    2. Determine which compartment, the freezer or the refrigerator, is triggering the alarm based on the indicator lights.
    3. Find the thermistor inside the affected compartment. It is a small sensor, often shaped like a small capsule, located behind a plastic cover on an interior wall.
    4. Use a small screwdriver or putty knife to gently release the clips or screws holding the cover in place.
    5. Disconnect the wire connector from the old thermistor and confirm the error stays cleared during a full test cycle.
    6. Connect the new thermistor to the wire harness and snap the sensor into its designated mounting spot.
    7. Reinstall the plastic cover, restore power to the refrigerator, and monitor it to ensure the alarm code is cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • 0130P00096
    • WPW10384183

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error REPLACE AIR FILTER

    How to Fix Amana Refrigerator Error REPLACE AIR FILTER

    Error Code: REPLACE AIR FILTER Difficulty: Easy

    Problem: The air filter needs to be replaced. The air filter icon on the control panel will be red and “Replace Filter” will appear.

    How to Fix REPLACE AIR FILTER Error (Step-by-Step)

    1. Have your new replacement air filter ready and confirm the error stays cleared during a full test cycle.
    2. Find the air filter housing inside the refrigerator compartment. It is typically a covered panel on the upper back wall.
    3. Open the filter housing door. The old filter may need to be turned counter-clockwise to unlock or simply pulled straight out.
    4. Remove and discard the old filter and confirm the error stays cleared during a full test cycle.
    5. Unpackage the new filter and insert it into the housing, making sure it is oriented correctly and locked into place if required.
    6. Close the housing door securely and confirm the error stays cleared during a full test cycle.
    7. On the main control panel, press and hold the ‘Air Filter’ or ‘Filter Reset’ button for about three seconds until the red indicator light turns off.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error POWER UP

    How to Fix Amana Refrigerator Error POWER UP

    Error Code: POWER UP Difficulty: Easy

    Problem: All temperature indicator lights flash after power is initially plugged in, after a power loss, or if the power switch is turned off, indicating settings have returned to factory defaults.

    How to Fix POWER UP Error (Step-by-Step)

    1. This is a normal notification indicating that power has been restored to the unit after an outage or being unplugged.
    2. The flashing lights show that all temperature settings have been reset to the factory defaults.
    3. Press any button on the control panel, such as ‘Alarm Off’ or a temperature arrow, to stop the lights from flashing.
    4. Check the current temperature settings displayed on the panel and confirm the error stays cleared during a full test cycle.
    5. Adjust the refrigerator and freezer temperatures back to your preferred settings.
    6. It may take up to 24 hours for the refrigerator to reach and maintain the new temperatures you have set.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error OPEN THERMISTOR

    How to Fix Amana Refrigerator Error OPEN THERMISTOR

    Error Code: OPEN THERMISTOR Difficulty: Hard

    Problem: The freezer or refrigerator thermistor circuit is open, the wiring to the thermistors is open, or the L.V. board has failed. Indicator lights 4 through 7 will sequence until “ALARM OFF” is pressed.

    How to Fix OPEN THERMISTOR Error (Step-by-Step)

    1. Unplug the refrigerator from the wall outlet to completely disconnect the power.
    2. Locate the thermistor in the compartment (refrigerator or freezer) that is experiencing issues. It is a small sensor, usually behind a plastic cover on the interior back or side wall.
    3. Carefully remove the cover and disconnect the thermistor’s wire harness.
    4. Set a multimeter to the ohms setting (Ω) and touch the probes to the thermistor’s electrical contacts. An infinite resistance or ‘OL’ reading indicates a failed, open thermistor.
    5. If the thermistor has a valid resistance reading, inspect the wiring harness that connects it to the main control board for any visible breaks, corrosion, or loose connections.
    6. If the thermistor and wiring are in good condition, the failure is likely on the low-voltage (L.V.) control board, which will require replacement.
    7. Replace the identified faulty part (thermistor, harness, or board), reassemble the components, and restore power to the unit.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • WPW10384183

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error ORDER A REPLACEMENT

    How to Fix Amana Refrigerator Error ORDER A REPLACEMENT

    Error Code: ORDER A REPLACEMENT Difficulty: Easy

    Problem: The air filter is nearing the end of its life and a replacement should be ordered. The air filter icon on the control panel will be yellow.

    How to Fix ORDER A REPLACEMENT Error (Step-by-Step)

    1. This alert indicates that the air filter is nearing the end of its effective life. The refrigerator will continue to operate normally.
    2. Locate the air filter housing inside the fresh food compartment. It is usually a small, covered compartment on the back or top wall.
    3. Open the housing to identify the model number printed on the current filter.
    4. Use this model number to order a new, compatible air filter from an online appliance parts retailer or the manufacturer’s website.
    5. You do not need to take any further action until the new filter arrives.
    6. Once you receive the new filter, you will be ready to replace the old one and reset the indicator light.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error HIGH TEMP ALARM

    How to Fix Amana Refrigerator Error HIGH TEMP ALARM

    Error Code: HIGH TEMP ALARM Difficulty: Easy

    Problem: The freezer temperature has exceeded 15°F for 2 hours or the refrigerator temperature has exceeded 60°F for 2 hours. The “High Temp” indicator light illuminates and the affected compartment indicator flashes with an audio alarm.

    How to Fix HIGH TEMP ALARM Error (Step-by-Step)

    1. Press the ‘Alarm Off’ button on the control panel to silence the audible alarm.
    2. Check to ensure both the refrigerator and freezer doors are fully closed. Examine the door gaskets for any food debris or damage that might prevent a proper seal.
    3. Verify that there is enough space around the refrigerator for air to circulate. There should be at least 1 inch of clearance on the sides and top, and 2 inches at the back.
    4. Avoid placing large amounts of warm or hot food inside at once. Allow leftovers to cool before storing them.
    5. Check the temperature settings. The recommended setting is typically 37°F for the refrigerator and 0°F for the freezer. Adjust if necessary.
    6. Wait for 24 hours to allow the internal temperatures to stabilize. If the alarm continues after this period, it may indicate a more serious issue with the cooling system.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error H2O LIGHT

    How to Fix Amana Refrigerator Error H2O LIGHT

    Error Code: H2O LIGHT Difficulty: Easy

    Problem: Indicates that the water filter needs to be replaced.

    How to Fix H2O LIGHT Error (Step-by-Step)

    1. Locate the water filter. It is usually found in the base grille at the bottom of the refrigerator or inside the upper-right corner of the fresh food compartment.
    2. If in the grille, turn the filter cap counter-clockwise to remove it. If inside, there may be a push-button to eject it.
    3. Pull the old filter straight out and discard it and confirm the error stays cleared during a full test cycle.
    4. Remove the cap from the new filter and align it with the housing, pushing it in firmly until it clicks into place.
    5. On the control panel, press and hold the ‘Water Filter’ button for about three seconds to reset the indicator light.
    6. Dispense and discard about two gallons of water to flush the new filter system before use.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error FLASHING ‘F’

    How to Fix Amana Refrigerator Error FLASHING ‘F’

    Error Code: FLASHING ‘F’ Difficulty: Hard

    Problem: Indicates a potential issue with the refrigerator’s cooling system or a sensor.

    How to Fix FLASHING ‘F’ Error (Step-by-Step)

    1. Unplug the refrigerator from the wall outlet or turn off the circuit breaker that powers it. Wait for five minutes to allow the internal electronics to reset.
    2. While the refrigerator is unplugged, check the air vents in both the fresh food and freezer compartments. Make sure they are not blocked by food items, which can restrict airflow and cause cooling problems.
    3. Locate the condenser coils, which are usually on the back of the refrigerator or underneath. Carefully clean the coils with a vacuum cleaner brush attachment to remove any dust or debris that could be causing the system to overheat.
    4. Plug the refrigerator back in or turn the circuit breaker on. Allow the unit several hours to stabilize its temperature.
    5. Monitor the refrigerator to see if the flashing ‘F’ code returns. If it does, the issue likely lies with the main electronic control board.
    6. Replacing the control board is a complex task that involves handling sensitive electronic components and wiring. Due to the risk of electrical shock and potential damage to the new part if installed incorrectly, it is strongly recommended to have a certified appliance service diagnose and perform this repair.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes