Category: Amana

  • How to Fix Amana Washer Error F7 E6

    How to Fix Amana Washer Error F7 E6

    Error Code: F7 E6 Difficulty: Hard

    Problem: Motor Fault

    How to Fix F7 E6 Error (Step-by-Step)

    1. Unplug the washer from the wall outlet and turn off the water faucets.
    2. Lean the washer forward to get to the bottom panel where the motor is located.
    3. Remove the drive belt by rotating the large pulley while walking the belt off.
    4. Disconnect the wire harnesses to the drive motor and the capacitor. Remove the bolts holding the motor in place and take out the old motor.
    5. Install the new drive motor (Part: WP21001950 or W10836348) and the new capacitor (Part: W10804665).
    6. Re-install the drive belt by starting it on the motor pulley and then stretching it over the large transmission pulley.
    7. Reconnect all wiring, return the washer to its standing position, and test a cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10836348 (Drive Motor)
    • WP21001950 (Drive Motor)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error F7 E7

    How to Fix Amana Washer Error F7 E7

    Error Code: F7 E7 Difficulty: Hard

    Problem: Motor Unable to Reach Target RPM

    How to Fix F7 E7 Error (Step-by-Step)

    1. Disconnect the washer from its power source to prevent electrical shock.
    2. Access the electronic control board by removing the top panel or the console, usually held by screws at the back or sides.
    3. Take a clear picture of the wire connections on the old board before disconnecting anything.
    4. Carefully unplug all the wire harnesses from the old control board. Note any locking tabs that need to be released.
    5. Remove the mounting screws that hold the control board in its housing and lift it out.
    6. Place the new control board (Part: W11170317 or W10785628) into the housing and secure it with the screws.
    7. Using your photo as a guide, reconnect all wire harnesses to the correct terminals on the new board, then reassemble the console and plug in the washer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W11170317 (Electronic Control Board)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error F8 E1

    How to Fix Amana Washer Error F8 E1

    Error Code: F8 E1 Difficulty: Moderate

    Problem: Low Flow of Water

    How to Fix F8 E1 Error (Step-by-Step)

    1. Unplug the washer and turn off the hot and cold water supply lines.
    2. Place a towel behind the washer to catch any residual water and disconnect the water inlet hoses from the back of the machine.
    3. Remove the screws from the back panel to access the water inlet valve at the top.
    4. Disconnect the wire harnesses attached to the valve solenoids and confirm the error stays cleared during a full test cycle.
    5. Remove the screws holding the water inlet valve assembly in place and remove the old valve.
    6. Install the new water inlet valve (Part: W11220230, 205613, or W11210459) and secure it with its mounting screws.
    7. Reconnect the wire harnesses and water hoses, then turn the water on and check for leaks before plugging the washer back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W11210459 (Water Inlet Valve)
    • W11220230 (Water Inlet Valve)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error F8 E2

    How to Fix Amana Washer Error F8 E2

    Error Code: F8 E2 Difficulty: Easy

    Problem: Dispenser System Problem

    How to Fix F8 E2 Error (Step-by-Step)

    1. Open the dispenser drawer and press the release tab to remove it completely from the washer.
    2. Separate the different components of the drawer, such as the siphon cover and inserts.
    3. Thoroughly wash all parts of the dispenser drawer with warm, soapy water and a soft brush to remove any built-up detergent or fabric softener residue.
    4. Clean the inside of the dispenser housing on the washer itself, paying attention to the area above where residue can accumulate.
    5. Rinse all parts with clean water and dry them completely before reassembling the drawer.
    6. Slide the clean dispenser drawer back into the washer until it clicks into place.
    7. Run a rinse cycle to ensure everything is functioning correctly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error F9 E1

    How to Fix Amana Washer Error F9 E1

    Error Code: F9 E1 Difficulty: Moderate

    Problem: Long Drain Time

    How to Fix F9 E1 Error (Step-by-Step)

    1. Unplug the washer from power before starting the repair and confirm the error stays cleared during a full test cycle.
    2. Check the drain hose at the back of the machine to ensure it is not kinked, bent, or clogged.
    3. Disconnect the drain hose from the household drain pipe to check for obstructions at the connection point.
    4. If the hose is clear, you will need to access the drain pump at the bottom of the washer by tilting the machine forward.
    5. Place a shallow pan and towels under the pump to catch water, then disconnect the hoses from the pump by releasing the spring clamps.
    6. Disconnect the pump’s wire connector and remove the screws holding it to the washer base. Install the new drain pump (Part: W10536347).
    7. Reconnect hoses and wires, then carefully set the washer upright, restore power, and test the drain function.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error FD

    How to Fix Amana Washer Error FD

    Error Code: FD Difficulty: Easy

    Problem: Internal Board Problem – Drive Motor

    How to Fix FD Error (Step-by-Step)

    1. Unplug the washing machine from the electrical outlet and confirm the error stays cleared during a full test cycle.
    2. Wait for at least 5 minutes. This allows the internal electronic components and control board to fully discharge and reset.
    3. While waiting, ensure the washer door is securely closed and there are no items obstructing the lock.
    4. Plug the washer back into the power outlet and confirm the error stays cleared during a full test cycle.
    5. Select a new wash cycle and press ‘Start’ to see if the reset has cleared the internal board problem.
    6. If the code reappears, there may be a more serious issue with the drive motor or control board that requires professional service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error FILL OR SENSING LIGHT ON

    How to Fix Amana Washer Error FILL OR SENSING LIGHT ON

    Error Code: FILL OR SENSING LIGHT ON Difficulty: Moderate

    Problem: Filling or Sensing

    How to Fix FILL OR SENSING LIGHT ON Error (Step-by-Step)

    1. Unplug the washer from the wall outlet to ensure safety.
    2. Turn off both the hot and cold water supply valves connected to the washer.
    3. Open the washer lid and check that the lid switch, a small plastic piece on the body that meets the lid, is not broken or obstructed.
    4. Carefully pull the washer away from the wall to access the back panel.
    5. Unscrew the mounting screws holding the top control panel in place and flip it back to access the lid switch and water valve connections.
    6. Inspect the wire harness connecting to the lid switch and the water inlet valve for any loose or damaged wires.
    7. If the wiring is secure and the lid switch appears damaged, it will need to be replaced to allow the washer to sense the lid is closed and begin the fill cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10838613 (Lid Switch)
    • WP8318084 (Lid Switch)
    • 205613 (Water Inlet Valve)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error HC

    How to Fix Amana Washer Error HC

    Error Code: HC Difficulty: Easy

    Problem: Hot and Cold Hoses are Reversed

    How to Fix HC Error (Step-by-Step)

    1. Turn off the hot and cold water faucets connected to the back of the washer.
    2. Use a pair of pliers to unscrew the metal fittings on both hoses from the washer’s water inlet valve.
    3. Look for the ‘H’ (Hot) and ‘C’ (Cold) labels on the washer’s inlet valve ports.
    4. Reconnect the hose coming from your home’s hot water supply to the ‘H’ port.
    5. Reconnect the hose from your cold water supply to the ‘C’ port.
    6. Tighten both hose connections by hand first, then give them a final quarter-turn with pliers to prevent leaks.
    7. Turn the water faucets back on fully and check for any drips before pushing the washer back into place.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error INT

    How to Fix Amana Washer Error INT

    Error Code: INT Difficulty: Easy

    Problem: Cycle Paused or Canceled

    How to Fix INT Error (Step-by-Step)

    1. Look at the control panel to see if the ‘Start/Pause’ button has been pressed, which can pause the cycle.
    2. Press the ‘Start/Pause’ button once to resume the current wash cycle.
    3. If you intended to stop the cycle completely, press and hold the ‘Cancel’ or ‘Power’ button for about three seconds.
    4. The washer will begin to drain any water in the tub, which may take a few minutes.
    5. The lid will unlock once the water has been drained.
    6. You can now select a new cycle and press ‘Start’ to begin a new wash.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LC

    How to Fix Amana Washer Error LC

    Error Code: LC Difficulty: Easy

    Problem: Control Lock Activated

    How to Fix LC Error (Step-by-Step)

    1. Locate the ‘Control Lock’ button on the washer’s control panel. It may be labeled or indicated by a small padlock icon.
    2. Press and hold the ‘Control Lock’ button for 3 to 5 seconds.
    3. The indicator light for the control lock feature should turn off.
    4. The washer’s controls are now unlocked, and you can select a cycle and start a load of laundry.
    5. To reactivate the lock and prevent accidental button presses, simply press and hold the same button again for 3 to 5 seconds until the light comes on.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.