Category: Amana

  • How to Fix Amana Washer Error F2 E1

    How to Fix Amana Washer Error F2 E1

    Error Code: F2 E1 Difficulty: Hard

    Problem: Stuck Key

    How to Fix F2 E1 Error (Step-by-Step)

    1. Perform a hard reset by unplugging the washer for at least 5 minutes. Plug it back in and test if the error is gone.
    2. If the error persists, unplug the washer again. You will need to access the user interface board in the main control console.
    3. To do this, you may need to remove screws from the back of the console or top panel of the washer to tilt or remove it.
    4. Take a clear photograph of the wiring connected to the user interface board.
    5. Disconnect the ribbon cables and any other wire harnesses from the old board.
    6. Remove the screws holding the user interface in place and swap it with the new part.
    7. Reconnect all wiring using your photo as a reference, reassemble the console, and restore power to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • Main Control Board

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F1 E1

    How to Fix Amana Washer Error F1 E1

    Error Code: F1 E1 Difficulty: Hard

    Problem: Main Control Fault

    How to Fix F1 E1 Error (Step-by-Step)

    1. Unplug the washer from the wall outlet to ensure safety.
    2. Turn off both the hot and cold water supply valves connected to the washer.
    3. Locate the main control board. This is typically found inside the top console panel or on the back of the machine.
    4. Take a clear picture of the wire connections to the board before you disconnect anything. This will be your guide for installation.
    5. Carefully disconnect all wiring harnesses from the old control board. Most connectors have a small locking tab you need to press.
    6. Remove the screws or release the clips holding the old board in place and gently lift it out.
    7. Install the new main control board, secure it, and reconnect all wiring harnesses by referring to the photo you took.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F0E9

    How to Fix Amana Washer Error F0E9

    Error Code: F0E9 Difficulty: Hard

    Problem: Unbalanced load.

    How to Fix F0E9 Error (Step-by-Step)

    1. Unplug the washer and turn off the water supply lines.
    2. Use a putty knife to press in and release the two clips located in the seam between the top and front panels. Hinge the top panel up and back.
    3. You will see four suspension rods, one at each corner, supporting the wash tub.
    4. Working on one corner at a time, slightly lift the tub to relieve tension. Unhook the top of the suspension rod from the tub support, then pull the entire rod assembly up and out of the washer base.
    5. Guide the new suspension rod down into the base, ensuring it is properly seated. Lift the tub again and hook the top of the new rod into place.
    6. Repeat this process for the remaining three rods, replacing them one by one.
    7. Lower the top panel, press down to secure the clips, reconnect power and water, and run a test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F0E8

    How to Fix Amana Washer Error F0E8

    Error Code: F0E8 Difficulty: Moderate

    Problem: Too much residual water has been detected in the washer.

    How to Fix F0E8 Error (Step-by-Step)

    1. Unplug the washer from its power source and turn off the water supply valves.
    2. Place towels on the floor and carefully tilt the washer forward, resting it against a wall for stability to access the bottom.
    3. Locate the drain pump, which is a small component with two large hoses attached.
    4. Put a shallow pan underneath the hoses to catch water. Use pliers to squeeze the clamps on the hoses and slide them off the pump ports.
    5. Disconnect the electrical wire connector from the pump and confirm the error stays cleared during a full test cycle.
    6. Remove the mounting screws that hold the old pump in place and take it out.
    7. Install the new pump, secure it with the screws, and reattach the hoses, clamps, and electrical connector before carefully returning the washer to its upright position.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F0E7

    How to Fix Amana Washer Error F0E7

    Error Code: F0E7 Difficulty: Easy

    Problem: Items were detected in the washer during the Clean Washer cycle.

    How to Fix F0E7 Error (Step-by-Step)

    1. Press the ‘Power’ button to cancel the ‘Clean Washer’ cycle.
    2. Open the washer lid and look inside the drum and confirm the error stays cleared during a full test cycle.
    3. Remove any forgotten items such as clothes, towels, or other laundry.
    4. The ‘Clean Washer’ cycle is meant to clean the inside of the machine and must be run completely empty.
    5. Close the lid securely and confirm the error stays cleared during a full test cycle.
    6. Select the ‘Clean Washer’ cycle again and press ‘Start’ with the now-empty drum.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F0 E2

    How to Fix Amana Washer Error F0 E2

    Error Code: F0 E2 Difficulty: Easy

    Problem: Over Suds Condition

    How to Fix F0 E2 Error (Step-by-Step)

    1. Do not add more detergent. The washer has detected too many suds and is attempting to correct the issue automatically.
    2. Allow the washer to complete its cycle. It may add extra rinses, which will extend the cycle time.
    3. After the cycle finishes, remove the laundry and confirm the error stays cleared during a full test cycle.
    4. To clear out residual suds from the machine, run a ‘Clean Washer’ cycle or a ‘Normal’ cycle on the hottest setting with one cup of white vinegar and no clothes.
    5. In the future, always use detergent specifically labeled for High-Efficiency (HE) machines.
    6. Reduce the amount of HE detergent used per load, as modern detergents are highly concentrated.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F# E#

    How to Fix Amana Washer Error F# E#

    Error Code: F# E# Difficulty: Easy

    Problem: System Code Error

    How to Fix F# E# Error (Step-by-Step)

    1. Press the ‘Power’ button to cancel the cycle and turn off the machine.
    2. Disconnect the washer from the electrical outlet and confirm the error stays cleared during a full test cycle.
    3. Let the washer remain without power for at least 5 minutes to reset the main control board.
    4. During this time, confirm the wall outlet is functional by testing it with a small lamp or other device.
    5. Plug the washer back in, ensuring a firm connection and confirm the error stays cleared during a full test cycle.
    6. Start a ‘Rinse & Spin’ cycle to check if the system error has been resolved.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error ERR

    How to Fix Amana Washer Error ERR

    Error Code: ERR Difficulty: Easy

    Problem: General Error

    How to Fix ERR Error (Step-by-Step)

    1. Press the ‘Start/Stop’ button to pause the current operation.
    2. Press the ‘Power’ button to turn the washer off completely.
    3. Unplug the washer’s power cord from the wall outlet and confirm the error stays cleared during a full test cycle.
    4. Wait for 5 minutes to allow the internal electronics to fully reset.
    5. Plug the power cord securely back into the outlet and confirm the error stays cleared during a full test cycle.
    6. Select a new wash cycle and press ‘Start’ to confirm the error is cleared.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error DOOR LOCKED

    How to Fix Amana Washer Error DOOR LOCKED

    Error Code: DOOR LOCKED Difficulty: Hard

    Problem: Indicates that the washer door is locked and cannot be opened.

    How to Fix DOOR LOCKED Error (Step-by-Step)

    1. Begin by unplugging the washer from the wall outlet to ensure your safety. Turn off the hot and cold water supply valves connected to the washer.
    2. Open the washer door. Use a Phillips screwdriver to remove the two screws that fasten the door lock assembly to the front panel of the machine.
    3. Locate the metal spring clamp that holds the large rubber door boot seal against the front panel. Carefully pry this clamp off using a spring expansion tool or pliers and set it aside.
    4. Gently peel the rubber door boot seal away from the front panel opening. You only need to create enough space to reach your hand behind the panel to access the door lock.
    5. Reach inside the opening and find the door lock assembly. Press the small tab on the wire harness connector to unplug it from the lock. You can now completely remove the old lock assembly from the washer.
    6. Position the new door lock assembly in place and securely plug in the wire harness connector. Align the lock with the screw holes on the front panel and reinstall the two screws you removed earlier.
    7. Carefully re-seat the rubber door boot seal onto the lip of the front panel, ensuring it is smooth and even. Reinstall the metal spring clamp to secure the boot seal. Plug the washer back in, turn the water on, and run a test cycle to confirm the door locks and the error is gone.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10804741
    • W10837741
    • W11307244

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error DONE LIGHT ON

    How to Fix Amana Washer Error DONE LIGHT ON

    Error Code: DONE LIGHT ON Difficulty: Easy

    Problem: Cycle Finished

    How to Fix DONE LIGHT ON Error (Step-by-Step)

    1. Recognize that the ‘Done’ light is a simple notification that the wash cycle has successfully completed.
    2. The machine has finished all washing, rinsing, and spinning stages.
    3. The door will be unlocked and safe to open and confirm the error stays cleared during a full test cycle.
    4. Open the washer door and transfer your clean clothes to the dryer or a clothesline.
    5. For best machine care, leave the washer door open for a while to allow the interior to dry completely.
    6. Press the ‘Power’ button to turn off the display and the machine.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes