Category: Amana

  • How to Fix Amana Dryer Error F2E1

    How to Fix Amana Dryer Error F2E1

    Error Code: F2E1 Difficulty: Moderate

    Problem: A button on the control panel is stuck or the user interface is faulty.

    How to Fix F2E1 Error (Step-by-Step)

    1. Unplug the dryer from its power source to ensure your safety.
    2. Remove the screws located on the back of the control console that hold it in place.
    3. Gently tilt the top of the control console forward to access the user interface board mounted inside.
    4. Take a photo of the wire connections to ensure you can reconnect them correctly.
    5. Carefully unplug all the wire harnesses connected to the faulty user interface board.
    6. Remove the screws that mount the board to the control console and lift the old board out.
    7. Install the new user interface board, secure it with the screws, reconnect all wire harnesses based on your photo, and reattach the control console.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W11194456
    • W11388023

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F29

    How to Fix Amana Dryer Error F29

    Error Code: F29 Difficulty: Moderate

    Problem: General error requiring a power cycle.

    How to Fix F29 Error (Step-by-Step)

    1. Disconnect the power cord from the wall outlet before beginning the repair.
    2. Open the dryer door to access the area around the opening.
    3. Remove the screws holding the top panel of the dryer on, located at the rear of the machine, and slide the top panel off.
    4. Locate the door switch, which is typically found near the top of the door opening.
    5. Disconnect the wire harness that plugs into the door switch.
    6. Depress the small locking tabs on the side of the switch and push it out from the front panel.
    7. Snap the new door switch into place from the front, reconnect the wire harness from behind, and reassemble the top panel.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F28

    How to Fix Amana Dryer Error F28

    Error Code: F28 Difficulty: Hard

    Problem: General error requiring a power cycle.

    How to Fix F28 Error (Step-by-Step)

    1. First, attempt a simple reset by unplugging the dryer from the power outlet for 5-10 minutes, then plugging it back in.
    2. If the error persists, unplug the dryer again and remove the top panel to access the internal components.
    3. Locate the main Central Control Unit (CCU), which is the primary circuit board for the dryer.
    4. Visually inspect the CCU for any burn marks, loose connections, or signs of damage.
    5. Check the wiring harness connecting the CCU to the Motor Control Unit (MCU) and other components, ensuring all plugs are seated firmly.
    6. If all connections appear secure and there is no visible damage, the CCU is likely faulty and needs to be replaced.
    7. Carefully disconnect all wire harnesses from the old board, remove it, install the new CCU, and reconnect everything exactly as it was.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • Motor Control Unit (MCU)
    • Central Control Unit (CCU)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F25

    How to Fix Amana Dryer Error F25

    Error Code: F25 Difficulty: Hard

    Problem: The inlet thermistor is shorted.

    How to Fix F25 Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet to prevent any electrical shock.
    2. Pull the dryer away from the wall and remove the screws securing the rear access panel.
    3. Locate the heater housing, which is a silver metal box, and find the intake thermistor mounted on it.
    4. Carefully disconnect the two wires attached to the thermistor terminals.
    5. Remove the screw that holds the thermistor to the heater housing and pull the old thermistor out.
    6. Place the new intake thermistor into the mounting hole, secure it with the screw, and reconnect the wires.
    7. Reattach the rear access panel, plug the dryer back in, and test for proper operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F23

    How to Fix Amana Dryer Error F23

    Error Code: F23 Difficulty: Hard

    Problem: Fault in the exhaust/outlet thermistor.

    How to Fix F23 Error (Step-by-Step)

    1. Ensure the dryer is completely unplugged from the power source.
    2. Remove the screws from the back of the dryer that hold the top panel in place, then slide the panel off.
    3. Remove the control panel console by taking out its mounting screws.
    4. Open the dryer door and remove the screws located inside the door frame that secure the front panel.
    5. Carefully lean the front panel forward, locate the thermistor on the blower housing, and disconnect its wire harness.
    6. Use a screwdriver to remove the single screw mounting the thermistor to the housing and remove the old part.
    7. Secure the new thermistor with the screw, plug in the wire harness, and reassemble the front panel, control console, and top panel.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error ERR

    How to Fix Amana Dryer Error ERR

    Error Code: ERR Difficulty: Moderate

    Problem: The dryer door is not completely closed or latched.

    How to Fix ERR Error (Step-by-Step)

    1. First, open the dryer door and close it firmly to ensure the latch is fully engaged. Check for any clothing or items obstructing the door.
    2. If the error continues, unplug the dryer from the power outlet.
    3. Open the dryer door and locate the door switch assembly inside the door frame.
    4. Use a putty knife to release the two clips holding the top panel down, located in the gap between the top and front panels. Hinge the top panel up and back.
    5. From the inside, locate the door switch. Unscrew it from the front panel and disconnect its wire harness.
    6. Connect the new door switch (Parts: 279570, WPW10610880), screw it back into the front panel.
    7. Lower the top panel and snap it back into place. Plug the dryer in and test by starting a cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WPW10610880

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error E2

    How to Fix Amana Dryer Error E2

    Error Code: E2 Difficulty: Moderate

    Problem: Indicates a shorted thermistor, causing the dryer to misread the temperature.

    How to Fix E2 Error (Step-by-Step)

    1. Unplug the dryer from the power source to prevent electrical shock.
    2. Remove the lower front panel to gain access to the internal components. This panel is often held by two screws at the bottom or clips at the top.
    3. Find the thermistor mounted on the exhaust blower housing. It’s a small plastic sensor with two wires leading to it.
    4. Carefully unplug the wire connector from the old thermistor and confirm the error stays cleared during a full test cycle.
    5. Use a nut driver or screwdriver to remove the single screw securing the thermistor to the housing.
    6. Place the new thermistor (Part: WP8577274) into the housing, fasten it with the screw, and plug the wire connector back in until it clicks.
    7. Reattach the lower panel, restore power to the dryer, and verify the fix by starting a new cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error E1

    How to Fix Amana Dryer Error E1

    Error Code: E1 Difficulty: Moderate

    Problem: Indicates an issue with the thermistor, specifically an open circuit. This can be caused by a faulty thermistor or a wiring problem.

    How to Fix E1 Error (Step-by-Step)

    1. Disconnect the dryer from the wall outlet to ensure safety.
    2. Access the thermistor, which is typically located on the blower housing. You may need to remove the lower front access panel by unscrewing it or releasing clips at the top.
    3. Locate the thermistor on the blower housing. It is a small black or gray component with a two-wire connector.
    4. Disconnect the wire harness attached to the thermistor. Squeeze the tab on the connector to release it.
    5. Remove the single screw, usually a quarter-inch hex head, that holds the thermistor in place.
    6. Install the new thermistor (Part: WP8577274), secure it with the screw, and firmly reconnect the wire harness.
    7. Reassemble the access panel, plug the dryer back in, and run a test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error CHECK VENT

    How to Fix Amana Dryer Error CHECK VENT

    Error Code: CHECK VENT Difficulty: Easy

    Problem: Indicates that the dryer vent is clogged or there is restricted airflow.

    How to Fix CHECK VENT Error (Step-by-Step)

    1. Pull out the dryer’s lint screen and clean it of all lint. If it has a waxy buildup from dryer sheets, wash it with a soft brush and soapy water, then let it dry completely.
    2. Unplug the dryer from the wall to ensure your safety during the next steps.
    3. Carefully pull the dryer away from the wall and detach the vent hose from the back of the machine.
    4. Clear any lint buildup from the dryer’s exhaust port and from the inside of the vent hose itself.
    5. Inspect the vent hose for any sections that are crushed or kinked, as this can severely limit airflow. Straighten them out.
    6. Use a specialized vent cleaning kit with a long brush to clean out the entire length of the ductwork that runs to the exterior of your home.
    7. Go outside and ensure the external vent flap is clean and can open and close without obstruction.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error 88

    How to Fix Amana Dryer Error 88

    Error Code: 88 Difficulty: Easy

    Problem: All display segments are lit up. This is a normal part of the diagnostic test mode to ensure the display is working correctly.

    How to Fix 88 Error (Step-by-Step)

    1. This display is not an error but indicates the dryer is in a check test mode.
    2. To exit this mode, press and hold the ‘Start’ or ‘Cancel’ button for a few seconds.
    3. If the display does not return to normal, the next step is to reset the machine’s main board.
    4. Unplug the dryer from its power source for at least 2 minutes.
    5. Plug the dryer back in. The display should now be clear and ready for normal cycle selection.
    6. If the ’88’ display is stuck and will not clear after a power cycle, the display control board may be faulty and require professional service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes