Category: Amana

  • How to Fix Amana Dryer Error F9FE

    How to Fix Amana Dryer Error F9FE

    Error Code: F9FE Difficulty: Hard

    Problem: Accessory brownout detected.

    How to Fix F9FE Error (Step-by-Step)

    1. Attempt to resolve the issue with a power cycle. Disconnect the dryer from the wall outlet or turn off the circuit breaker that supplies its power for 5 minutes.
    2. Unplug the dryer again for safety and confirm the error stays cleared during a full test cycle.
    3. A ‘brownout’ detection means the control board received insufficient voltage to operate correctly. This could be due to an issue with your home’s electrical supply or a fault in the dryer’s internal electronics.
    4. You can check that the dryer is plugged into the correct type of outlet and that the plug is secure. Also, avoid using extension cords.
    5. If the home’s voltage is stable, the error indicates a failure within the dryer’s main control board.
    6. Due to the electrical diagnosis required, it is recommended to have a certified service inspect the dryer and replace the necessary components.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dryer

    Focused repair path: dryer airflow, heating, sensor, motor, door switch, belt, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before inspection, then clear the lint screen, blower area, vent run, and exterior hood before replacing heat parts.
    2. Confirm whether the dryer starts, tumbles, heats, and advances through the cycle; the missing function narrows the repair path.
    3. For heat faults, inspect airflow first, then the thermal fuse, thermistor, element or gas ignition path, wiring, and control output.
    4. For start or tumble faults, check the door switch, belt switch, motor circuit, harness, and control connections before ordering parts.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • W10542001
    • W10756689
    • W11417009

    When It’s Better to Replace Than Repair

    Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
    Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
    For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Thermal fuse or heater failures keep returning
    • [OK]Belt, roller, or motor repairs exceed unit value
    • [OK]Door switch or control issues stack with other faults
    • [OK]Older dryer has long dry times even after vent cleaning

    Recommended Dryer Replacement Options

    Electric Dryers

    240V Vented Models

    • Most common electric replacement type
    • Confirm 3-prong vs 4-prong cord needs
    • Verify vent path and laundry-space depth

    Shop Electric Dryers

    Gas Dryers

    Natural Gas Dryer Options

    • Confirm gas supply and shutoff location
    • Use qualified installation when required
    • Do not substitute electric for gas without planning

    Compare Gas Dryers

    Compact and Ventless

    Small-Space Dryer Choices

    • Good for apartments and tight closets
    • Confirm ventless condensation requirements
    • Check capacity before replacing full-size units

    View Compact Dryers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F9FF

    How to Fix Amana Dryer Error F9FF

    Error Code: F9FF Difficulty: Hard

    Problem: Accessory power surge detected.

    How to Fix F9FF Error (Step-by-Step)

    1. Begin by resetting the dryer’s electronics. Unplug the appliance from the power outlet or switch off the circuit breaker for 5 minutes.
    2. Disconnect the dryer from power before any further inspection and confirm the error stays cleared during a full test cycle.
    3. Replacing the main control board is an intricate job that requires careful handling of electronic parts and wiring.
    4. To avoid risk of injury or further damage to the appliance, it is best to entrust this repair to a qualified service professional.
    5. Turn the appliance off, wait about 2 minutes, then turn it back on.
    6. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
    7. Make sure all doors, lids, and hoses are fully closed and seated correctly.

    What to Check Next on This Amana Dryer

    Focused repair path: dryer airflow, heating, sensor, motor, door switch, belt, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before inspection, then clear the lint screen, blower area, vent run, and exterior hood before replacing heat parts.
    2. Confirm whether the dryer starts, tumbles, heats, and advances through the cycle; the missing function narrows the repair path.
    3. For heat faults, inspect airflow first, then the thermal fuse, thermistor, element or gas ignition path, wiring, and control output.
    4. For start or tumble faults, check the door switch, belt switch, motor circuit, harness, and control connections before ordering parts.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • W10542001
    • W10756689
    • W11417009

    When It’s Better to Replace Than Repair

    Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
    Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
    For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Thermal fuse or heater failures keep returning
    • [OK]Belt, roller, or motor repairs exceed unit value
    • [OK]Door switch or control issues stack with other faults
    • [OK]Older dryer has long dry times even after vent cleaning

    Recommended Dryer Replacement Options

    Electric Dryers

    240V Vented Models

    • Most common electric replacement type
    • Confirm 3-prong vs 4-prong cord needs
    • Verify vent path and laundry-space depth

    Shop Electric Dryers

    Gas Dryers

    Natural Gas Dryer Options

    • Confirm gas supply and shutoff location
    • Use qualified installation when required
    • Do not substitute electric for gas without planning

    Compare Gas Dryers

    Compact and Ventless

    Small-Space Dryer Choices

    • Good for apartments and tight closets
    • Confirm ventless condensation requirements
    • Check capacity before replacing full-size units

    View Compact Dryers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error FC E1

    How to Fix Amana Dryer Error FC E1

    Error Code: FC E1 Difficulty: Easy

    Problem: The appliance could not connect to the router. This could be due to a connection timeout, poor signal strength, a failed router, or an issue with the Wi-Fi module in the appliance.

    How to Fix FC E1 Error (Step-by-Step)

    1. Check your home’s Wi-Fi router to ensure it is powered on and has a stable internet connection. Other devices in your home should be able to connect to it.
    2. Move the router closer to the dryer if possible, or remove any obstructions that might be blocking the signal, such as thick walls or other large appliances.
    3. Try to restart your router by unplugging it from power for one minute and then plugging it back in. Wait for it to fully reboot before checking the dryer again.
    4. On your dryer’s control panel, navigate to the Wi-Fi settings and attempt to reconnect to your home network. You may need to re-enter your Wi-Fi password.
    5. Ensure you are connecting to a 2.4GHz network, as many appliances are not compatible with 5GHz networks.
    6. If the connection still fails, try resetting the network settings on your dryer through the settings menu.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dryer

    Focused repair path: dryer airflow, heating, sensor, motor, door switch, belt, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before inspection, then clear the lint screen, blower area, vent run, and exterior hood before replacing heat parts.
    2. Confirm whether the dryer starts, tumbles, heats, and advances through the cycle; the missing function narrows the repair path.
    3. For heat faults, inspect airflow first, then the thermal fuse, thermistor, element or gas ignition path, wiring, and control output.
    4. For start or tumble faults, check the door switch, belt switch, motor circuit, harness, and control connections before ordering parts.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana dryer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dryer thermal fuse
      Common replacement category: Thermal fuse
      Fit note: Exact OEM part number varies by complete Amana dryer model number. Confirm compatibility before buying.
      Why this category can matter: no-heat or no-start symptoms after venting and power checks.

      Search Amazon for Whirlpool dryer thermal fuse

    • Whirlpool dryer heating element
      Common replacement category: Heating element
      Fit note: Exact OEM part number varies by complete Amana dryer model number. Confirm compatibility before buying.
      Why this category can matter: electric dryer no-heat symptoms after airflow checks.

      Search Amazon for Whirlpool dryer heating element

    • Whirlpool dryer control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana dryer model number. Confirm compatibility before buying.
      Why this category can matter: cycle-control or repeated electronic faults after wiring checks.

      Search Amazon for Whirlpool dryer control board

    Before ordering: match the part to the complete Amana dryer model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
    Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
    For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Thermal fuse or heater failures keep returning
    • [OK]Belt, roller, or motor repairs exceed unit value
    • [OK]Door switch or control issues stack with other faults
    • [OK]Older dryer has long dry times even after vent cleaning

    Recommended Dryer Replacement Options

    Electric Dryers

    240V Vented Models

    • Most common electric replacement type
    • Confirm 3-prong vs 4-prong cord needs
    • Verify vent path and laundry-space depth

    Shop Electric Dryers

    Gas Dryers

    Natural Gas Dryer Options

    • Confirm gas supply and shutoff location
    • Use qualified installation when required
    • Do not substitute electric for gas without planning

    Compare Gas Dryers

    Compact and Ventless

    Small-Space Dryer Choices

    • Good for apartments and tight closets
    • Confirm ventless condensation requirements
    • Check capacity before replacing full-size units

    View Compact Dryers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error WET

    How to Fix Amana Dryer Error WET

    Error Code: WET Difficulty: Easy

    Problem: The drying cycle has just begun, and the load is still wet.

    How to Fix WET Error (Step-by-Step)

    1. This is an informational message, not an error code. It appears at the beginning of a sensor-based drying cycle.
    2. The ‘WET’ indicator simply means that the moisture sensors inside the dryer drum have detected that the clothes are still wet.
    3. No action is required from you. The dryer is operating as intended.
    4. The message will disappear on its own as the clothes begin to dry and the moisture level decreases.
    5. You can allow the cycle to continue normally. The dryer will automatically adjust the drying time based on the sensor readings.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    What to Check Next on This Amana Dryer

    Focused repair path: dryer airflow, heating, sensor, motor, door switch, belt, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before inspection, then clear the lint screen, blower area, vent run, and exterior hood before replacing heat parts.
    2. Confirm whether the dryer starts, tumbles, heats, and advances through the cycle; the missing function narrows the repair path.
    3. For heat faults, inspect airflow first, then the thermal fuse, thermistor, element or gas ignition path, wiring, and control output.
    4. For start or tumble faults, check the door switch, belt switch, motor circuit, harness, and control connections before ordering parts.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana dryer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dryer thermal fuse
      Common replacement category: Thermal fuse
      Fit note: Exact OEM part number varies by complete Amana dryer model number. Confirm compatibility before buying.
      Why this category can matter: no-heat or no-start symptoms after venting and power checks.

      Search Amazon for Whirlpool dryer thermal fuse

    • Whirlpool dryer heating element
      Common replacement category: Heating element
      Fit note: Exact OEM part number varies by complete Amana dryer model number. Confirm compatibility before buying.
      Why this category can matter: electric dryer no-heat symptoms after airflow checks.

      Search Amazon for Whirlpool dryer heating element

    • Whirlpool dryer control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana dryer model number. Confirm compatibility before buying.
      Why this category can matter: cycle-control or repeated electronic faults after wiring checks.

      Search Amazon for Whirlpool dryer control board

    Before ordering: match the part to the complete Amana dryer model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
    Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
    For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Thermal fuse or heater failures keep returning
    • [OK]Belt, roller, or motor repairs exceed unit value
    • [OK]Door switch or control issues stack with other faults
    • [OK]Older dryer has long dry times even after vent cleaning

    Recommended Dryer Replacement Options

    Electric Dryers

    240V Vented Models

    • Most common electric replacement type
    • Confirm 3-prong vs 4-prong cord needs
    • Verify vent path and laundry-space depth

    Shop Electric Dryers

    Gas Dryers

    Natural Gas Dryer Options

    • Confirm gas supply and shutoff location
    • Use qualified installation when required
    • Do not substitute electric for gas without planning

    Compare Gas Dryers

    Compact and Ventless

    Small-Space Dryer Choices

    • Good for apartments and tight closets
    • Confirm ventless condensation requirements
    • Check capacity before replacing full-size units

    View Compact Dryers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error DC

    How to Fix Amana Dryer Error DC

    Error Code: DC Difficulty: Easy

    Problem: The dryer door is open.

    How to Fix DC Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to ensure your safety.
    2. Locate the door switch, which is typically found just inside the dryer door frame.
    3. Use a putty knife or a thin screwdriver to gently pry the top of the dryer open. Release the two clips that hold the top down, one on each side.
    4. With the top panel lifted, you will see the door switch and its wiring harness. Disconnect the wiring harness from the switch.
    5. Remove the screws that hold the door switch in place. The old switch can now be removed.
    6. Install the new door switch, making sure to secure it with the screws you just removed.
    7. Reconnect the wiring harness, lower the top panel, and snap it back into place. Plug the dryer back in and test the door.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dryer

    Focused repair path: dryer airflow, heating, sensor, motor, door switch, belt, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before inspection, then clear the lint screen, blower area, vent run, and exterior hood before replacing heat parts.
    2. Confirm whether the dryer starts, tumbles, heats, and advances through the cycle; the missing function narrows the repair path.
    3. For heat faults, inspect airflow first, then the thermal fuse, thermistor, element or gas ignition path, wiring, and control output.
    4. For start or tumble faults, check the door switch, belt switch, motor circuit, harness, and control connections before ordering parts.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    When It’s Better to Replace Than Repair

    Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
    Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
    For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Thermal fuse or heater failures keep returning
    • [OK]Belt, roller, or motor repairs exceed unit value
    • [OK]Door switch or control issues stack with other faults
    • [OK]Older dryer has long dry times even after vent cleaning

    Recommended Dryer Replacement Options

    Electric Dryers

    240V Vented Models

    • Most common electric replacement type
    • Confirm 3-prong vs 4-prong cord needs
    • Verify vent path and laundry-space depth

    Shop Electric Dryers

    Gas Dryers

    Natural Gas Dryer Options

    • Confirm gas supply and shutoff location
    • Use qualified installation when required
    • Do not substitute electric for gas without planning

    Compare Gas Dryers

    Compact and Ventless

    Small-Space Dryer Choices

    • Good for apartments and tight closets
    • Confirm ventless condensation requirements
    • Check capacity before replacing full-size units

    View Compact Dryers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error HE

    How to Fix Amana Dryer Error HE

    Error Code: HE Difficulty: Moderate

    Problem: There is a heating error, potentially due to a restricted vent system or an issue with the thermistor.

    How to Fix HE Error (Step-by-Step)

    1. Disconnect the dryer from the power source. Safety first! and confirm the error stays cleared during a full test cycle.
    2. Pull the dryer away from the wall to access the exhaust vent. Disconnect the vent from the dryer and the wall, and inspect it for any blockages. Clean it out thoroughly.
    3. If the vent is clear, the issue may be the heating element. To access it, you’ll need to remove the back panel of the dryer.
    4. Locate the heating element, which is a metal canister containing coils. Visually inspect the coils for any breaks. If you see a break, the element needs to be replaced.
    5. If there are no visible breaks, test the heating element and the thermistor for continuity using a multimeter. A reading of infinity indicates a faulty part that needs replacement.
    6. To replace a part, disconnect the wires, remove the screws holding it in place, and install the new one.
    7. Reassemble the dryer, reconnect the vent, and plug it back in to test its operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WPY503978
    • WP31001590
    • WP35001191

    When It’s Better to Replace Than Repair

    Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
    Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
    For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Thermal fuse or heater failures keep returning
    • [OK]Belt, roller, or motor repairs exceed unit value
    • [OK]Door switch or control issues stack with other faults
    • [OK]Older dryer has long dry times even after vent cleaning

    Recommended Dryer Replacement Options

    Electric Dryers

    240V Vented Models

    • Most common electric replacement type
    • Confirm 3-prong vs 4-prong cord needs
    • Verify vent path and laundry-space depth

    Shop Electric Dryers

    Gas Dryers

    Natural Gas Dryer Options

    • Confirm gas supply and shutoff location
    • Use qualified installation when required
    • Do not substitute electric for gas without planning

    Compare Gas Dryers

    Compact and Ventless

    Small-Space Dryer Choices

    • Good for apartments and tight closets
    • Confirm ventless condensation requirements
    • Check capacity before replacing full-size units

    View Compact Dryers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error TS / T5

    How to Fix Amana Dryer Error TS / T5

    Error Code: TS / T5 Difficulty: Moderate

    Problem: Thermistor error. This indicates a problem with the temperature sensor.

    How to Fix TS / T5 Error (Step-by-Step)

    1. Turn off the power to the dryer at the circuit breaker.
    2. The thermistor is located on the blower housing. You will need to remove the back panel of the dryer to access it.
    3. Once you have located the thermistor, disconnect the two wires attached to it.
    4. Use a multimeter to test the thermistor for resistance. At room temperature, it should read around 10,000 ohms. A significantly different reading, or a reading of infinity, means the thermistor is bad and needs to be replaced.
    5. To replace the thermistor, simply unscrew it, and screw the new one in its place.
    6. Reconnect the wires, reattach the back panel, and restore power to the dryer.
    7. Run a test cycle to ensure the dryer is heating properly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dryer

    Focused repair path: dryer airflow, heating, sensor, motor, door switch, belt, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before inspection, then clear the lint screen, blower area, vent run, and exterior hood before replacing heat parts.
    2. Confirm whether the dryer starts, tumbles, heats, and advances through the cycle; the missing function narrows the repair path.
    3. For heat faults, inspect airflow first, then the thermal fuse, thermistor, element or gas ignition path, wiring, and control output.
    4. For start or tumble faults, check the door switch, belt switch, motor circuit, harness, and control connections before ordering parts.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • WP35001191
    • DC32-00007A

    When It’s Better to Replace Than Repair

    Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
    Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
    For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Thermal fuse or heater failures keep returning
    • [OK]Belt, roller, or motor repairs exceed unit value
    • [OK]Door switch or control issues stack with other faults
    • [OK]Older dryer has long dry times even after vent cleaning

    Recommended Dryer Replacement Options

    Electric Dryers

    240V Vented Models

    • Most common electric replacement type
    • Confirm 3-prong vs 4-prong cord needs
    • Verify vent path and laundry-space depth

    Shop Electric Dryers

    Gas Dryers

    Natural Gas Dryer Options

    • Confirm gas supply and shutoff location
    • Use qualified installation when required
    • Do not substitute electric for gas without planning

    Compare Gas Dryers

    Compact and Ventless

    Small-Space Dryer Choices

    • Good for apartments and tight closets
    • Confirm ventless condensation requirements
    • Check capacity before replacing full-size units

    View Compact Dryers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error 1-1

    How to Fix Amana Dishwasher Error 1-1

    Error Code: 1-1 Difficulty: Hard

    Problem: Stuck key detected in keypad or keypad connection.

    How to Fix 1-1 Error (Step-by-Step)

    1. Disconnect Power: Turn off the circuit breaker or unplug the dishwasher from the wall outlet to ensure your safety.
    2. Access the Control Panel: Open the dishwasher door and remove the screws, typically Torx T-15, that hold the inner door panel to the outer door panel.
    3. Separate Door Panels: Gently separate the inner and outer door panels to expose the control panel and main control board.
    4. Photograph Wiring: Before disconnecting anything, take a clear picture of the wire harness connections to the control board for easy reference during reassembly.
    5. Disconnect and Remove Old Part: Carefully unplug the wire harnesses from the control board. Release any clips or screws holding the control panel assembly in place and remove it.
    6. Install New Part: Position the new control panel or control board, securing it with the original clips or screws.
    7. Reconnect and Reassemble: Using your photo as a guide, reconnect the wire harnesses to the new control board. Rejoin the inner and outer door panels and secure them with the screws.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.

      Search Amazon for Whirlpool dishwasher drain pump

    • Whirlpool dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.

      Search Amazon for Whirlpool dishwasher water inlet valve

    • Whirlpool dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating error-code or control faults after wiring and latch checks.

      Search Amazon for Whirlpool dishwasher control board

    Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error 1-2

    How to Fix Amana Dishwasher Error 1-2

    Error Code: 1-2 Difficulty: Hard

    Problem: Control software issue – damaged or corrupted memory on control board or incompatible software.

    How to Fix 1-2 Error (Step-by-Step)

    1. Disconnect the dishwasher from power by unplugging it from the wall outlet or shutting off the corresponding circuit breaker in your home’s electrical panel.
    2. Open the dishwasher door and remove the screws holding the inner door panel to the outer panel. These are typically located around the perimeter of the inner door.
    3. Carefully separate the inner and outer door panels to expose the internal components. The main control board is usually a green circuit board housed in a plastic case, often located at the top or side of the door assembly.
    4. Take a clear photo of the wiring connections on the old control board to use as a reference. This will ensure you reconnect everything correctly on the new board.
    5. Gently disconnect all wire harnesses attached to the old control board. Most connectors have a small locking tab that needs to be pressed to release the plug.
    6. Remove the screws or release the clips holding the old control board in its housing and carefully take it out.
    7. Install the new control board, secure it in place, and reconnect all the wire harnesses by referring to the photo you took earlier. Ensure each connector is firmly seated.
    8. Reassemble the dishwasher door panels, restore power to the appliance, and run a test cycle to confirm the repair.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.

      Search Amazon for Whirlpool dishwasher drain pump

    • Whirlpool dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.

      Search Amazon for Whirlpool dishwasher water inlet valve

    • Whirlpool dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating error-code or control faults after wiring and latch checks.

      Search Amazon for Whirlpool dishwasher control board

    Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error 2-1

    How to Fix Amana Dishwasher Error 2-1

    Error Code: 2-1 Difficulty: Hard

    Problem: Control software issue – damaged or corrupted memory on control board, or incompatible software.

    How to Fix 2-1 Error (Step-by-Step)

    1. Disconnect the dishwasher from power by turning off the circuit breaker or unplugging the unit from the wall outlet.
    2. Remove the screws securing the inner door panel to the outer door panel. The location and number of screws will vary by model, but they are typically around the perimeter of the inner door.
    3. With the screws removed, carefully separate the inner and outer door panels to expose the dishwasher’s internal components. Locate the main control board, which is usually a green circuit board housed in a plastic case.
    4. Take a clear photo of the wiring connections on the control board for reference. Carefully disconnect each wire harness from the old control board. Release any locking tabs on the connectors before pulling.
    5. Remove the screws or release the plastic tabs holding the old control board in its housing and remove it from the dishwasher.
    6. Place the new control board into the housing and secure it with the screws or tabs. Using your photo as a guide, reconnect all the wire harnesses to the correct terminals on the new board, ensuring they click securely into place.
    7. Reassemble the dishwasher door by aligning the inner and outer panels and reinstalling all the screws. Restore power to the dishwasher and run a test cycle to ensure the new control board is functioning correctly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.

      Search Amazon for Whirlpool dishwasher drain pump

    • Whirlpool dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.

      Search Amazon for Whirlpool dishwasher water inlet valve

    • Whirlpool dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating error-code or control faults after wiring and latch checks.

      Search Amazon for Whirlpool dishwasher control board

    Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes