Category: Amana

  • How to Fix Amana Refrigerator Error TEMPERATURE ALARM

    How to Fix Amana Refrigerator Error TEMPERATURE ALARM

    Error Code: TEMPERATURE ALARM Difficulty: Hard

    Problem: Indicates that the internal temperature of the refrigerator or freezer has exceeded a safe level.

    How to Fix TEMPERATURE ALARM Error (Step-by-Step)

    1. Unplug the refrigerator from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Locate the thermistor inside the fresh food or freezer compartment. It is usually behind a small plastic cover on the side or back wall.
    3. Gently pry off the cover with a small flathead screwdriver.
    4. Disconnect the wire harness attached to the thermistor and confirm the error stays cleared during a full test cycle.
    5. Remove the old thermistor. It may be held in place by a clip or screw.
    6. Install the new thermistor and reconnect the wire harness and confirm the error stays cleared during a full test cycle.
    7. Snap the cover back into place and plug the refrigerator back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • Thermistor (Temperature Sensor): W10316760
    • Thermistor (Temperature Sensor): WPW10383615

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error DF

    How to Fix Amana Refrigerator Error DF

    Error Code: DF Difficulty: Easy

    Problem: Door Switch Problem or Door Not Closing Properly.

    How to Fix DF Error (Step-by-Step)

    1. Check for any items inside the refrigerator that may be blocking the door from closing completely.
    2. Inspect the door gaskets (the rubber seals around the door) for any food debris or spills and clean them with warm, soapy water.
    3. Ensure the refrigerator is level. Use a level to check and adjust the leveling feet at the bottom of the unit if necessary.
    4. Gently push the door shut to ensure the magnetic seal is engaging properly.
    5. If the door still does not close correctly, check the door hinges for any signs of damage or misalignment.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error DR

    How to Fix Amana Refrigerator Error DR

    Error Code: DR Difficulty: Moderate

    Problem: Door Switch Problem or Door Not Closing Properly.

    How to Fix DR Error (Step-by-Step)

    1. Disconnect the refrigerator from its power source and confirm the error stays cleared during a full test cycle.
    2. Locate the door switch, which is typically a small plunger-style switch located in the door frame.
    3. Use a putty knife or a small flathead screwdriver to gently pry the old switch out of the door frame.
    4. Disconnect the two wires attached to the back of the old switch.
    5. Connect the wires to the terminals on the new door switch.
    6. Carefully press the new switch into the opening in the door frame until it snaps into place.
    7. Reconnect the refrigerator to power and test the new switch by opening and closing the door to see if the interior light turns on and off.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • Door Switch: W11396033

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F4E4

    How to Fix Amana Dryer Error F4E4

    Error Code: F4E4 Difficulty: Easy

    Problem: General error requiring a power cycle.

    How to Fix F4E4 Error (Step-by-Step)

    1. Unplug the dryer’s power cord directly from the wall outlet.
    2. Wait for at least 5 minutes. This allows the internal computer and electronic components to fully reset.
    3. While waiting, ensure the dryer door is securely closed and confirm the error stays cleared during a full test cycle.
    4. Plug the power cord firmly back into the wall outlet.
    5. Select a new drying cycle and press the ‘Start’ button to resume normal operation.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F4E1

    How to Fix Amana Dryer Error F4E1

    Error Code: F4E1 Difficulty: Hard

    Problem: Indicates a problem with the heater or heater relays.

    How to Fix F4E1 Error (Step-by-Step)

    1. Unplug the dryer from the power source to prevent electrical shock.
    2. Remove the top panel of the dryer by taking out the screws at the back or top edge.
    3. Locate the main control board, which is usually housed in a plastic casing at the front of the dryer.
    4. Take a clear picture of the wire connections before disconnecting anything to ensure you can reconnect them correctly.
    5. Carefully disconnect all the wire harnesses from the old control board.
    6. Release the locking tabs or remove the screws holding the control board in place and remove it.
    7. Install the new control board, reconnect all wire harnesses according to your photo, and reassemble the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W11537223

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F3E5

    How to Fix Amana Dryer Error F3E5

    Error Code: F3E5 Difficulty: Hard

    Problem: The moisture sensor has not detected any data for five consecutive loads.

    How to Fix F3E5 Error (Step-by-Step)

    1. Unplug the dryer from its power source and confirm the error stays cleared during a full test cycle.
    2. Open the dryer door to access the lint filter area where the moisture sensor strips are located.
    3. Use a small screwdriver to carefully remove the old sensor strips from their plastic housing.
    4. Clean the mounting area thoroughly with rubbing alcohol and a clean cloth to remove any residue.
    5. Firmly press the new moisture sensor strips into place until they click and are seated securely.
    6. After installation, plug the dryer back in and run a small, damp load to test the new sensors.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W11537223
    • WPW10541265

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F3E4

    How to Fix Amana Dryer Error F3E4

    Error Code: F3E4 Difficulty: Hard

    Problem: Indicates an open or shorted outlet thermistor.

    How to Fix F3E4 Error (Step-by-Step)

    1. Disconnect the dryer from the wall outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Remove the rear panel of the dryer by unscrewing the screws holding it in place.
    3. Locate the outlet thermistor on the heater housing, which looks like a small, black plastic sensor.
    4. Unplug the wire harness connected to the thermistor and confirm the error stays cleared during a full test cycle.
    5. Remove the single screw that fastens the thermistor to the housing and take out the old part.
    6. Place the new thermistor into position, secure it with the screw, and plug in the wire harness.
    7. Reattach the rear panel, plug the dryer in, and run a cycle to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W11537223

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F3E3

    How to Fix Amana Dryer Error F3E3

    Error Code: F3E3 Difficulty: Hard

    Problem: Indicates a fault with the inlet thermistor (temperature sensor).

    How to Fix F3E3 Error (Step-by-Step)

    1. Ensure the dryer is unplugged from the power outlet and confirm the error stays cleared during a full test cycle.
    2. You will need to access the back of the dryer. Remove the rear panel by taking out the screws around its perimeter.
    3. Locate the inlet thermistor, which is a small sensor mounted on the blower housing.
    4. Disconnect the wire connector attached to the thermistor and confirm the error stays cleared during a full test cycle.
    5. Remove the screw holding the thermistor in place and remove the old sensor.
    6. Install the new thermistor, secure it with the screw, and reconnect the wire connector.
    7. Replace the rear panel and plug the dryer in to check if the error is cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WP8577274

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F3E1

    How to Fix Amana Dryer Error F3E1

    Error Code: F3E1 Difficulty: Hard

    Problem: Indicates an issue with the pressure switch.

    How to Fix F3E1 Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to ensure safety.
    2. Locate the pressure switch. It is typically found inside the control panel or on the main housing, connected by a thin hose.
    3. Carefully disconnect the wire harness and the hose from the old pressure switch.
    4. Remove the screws or clips holding the old switch in place and take it out.
    5. Install the new pressure switch, securing it with the screws or clips.
    6. Reconnect the wire harness and the hose to the new switch.
    7. Reassemble any panels you removed and plug the dryer back in to test its operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WP8577274

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error F31

    How to Fix Amana Dryer Error F31

    Error Code: F31 Difficulty: Easy

    Problem: Low or no line voltage is detected, preventing the heater from turning on.

    How to Fix F31 Error (Step-by-Step)

    1. Check that the dryer’s power cord is pushed all the way into the wall outlet.
    2. Go to your home’s main electrical panel (breaker box) and confirm the error stays cleared during a full test cycle.
    3. Locate the circuit breaker dedicated to the dryer. Electric dryers use a double breaker, which is two breakers linked together.
    4. If the breaker is in the middle (tripped) position, you must first push it fully to the ‘OFF’ position.
    5. After turning it fully off, push the breaker firmly to the ‘ON’ position to restore power.
    6. If the breaker trips again as soon as you start the dryer, do not reset it again. There may be a problem with your home’s wiring or the dryer itself that requires a professional electrician.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes