Category: Amana

  • How to Fix Amana Dryer Error 6E

    How to Fix Amana Dryer Error 6E

    Error Code: 6E Difficulty: Easy

    Problem: Service Required.

    How to Fix 6E Error (Step-by-Step)

    1. Attempt to clear the error by pressing the ‘Cancel’ or ‘Stop’ button on the control panel.
    2. If the code persists, unplug the dryer from the wall outlet or switch off the power at the home’s circuit breaker panel.
    3. Wait for a minimum of 5 minutes before restoring power. This process can reset the dryer’s internal checks.
    4. Plug the dryer back in or flip the circuit breaker on.
    5. Try to initiate a drying cycle and confirm the error stays cleared during a full test cycle.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error 3E

    How to Fix Amana Dryer Error 3E

    Error Code: 3E Difficulty: Easy

    Problem: Service Required.

    How to Fix 3E Error (Step-by-Step)

    1. First, try to clear the code by pressing the ‘Stop’ or ‘Cancel’ button.
    2. If the code remains, perform a power cycle by unplugging the dryer from the electrical outlet or shutting it off at the circuit breaker.
    3. Let the dryer remain without power for at least 5 minutes. This allows the internal computer to perform a hard reset.
    4. Restore power by plugging the unit back in or turning the breaker on.
    5. Select a new cycle and press ‘Start’ to see if the error has cleared.
    6. If the ‘3E’ code returns, it signifies an internal component failure that requires diagnosis and repair by a professional service service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error 3 BEEPS

    How to Fix Amana Dryer Error 3 BEEPS

    Error Code: 3 BEEPS Difficulty: Moderate

    Problem: Can indicate a variety of issues, including a problem with the door switch or water getting into the control panel.

    How to Fix 3 BEEPS Error (Step-by-Step)

    1. Disconnect the dryer from its power source by unplugging it from the wall outlet.
    2. Open the dryer door and locate the door switch, which is typically a small plastic switch around the frame that the door presses when closed.
    3. Check that the plastic peg or actuator on the door itself is not broken and aligns correctly with the switch.
    4. To replace the switch, you may need to remove the dryer’s top or front panel to access its housing and wiring.
    5. Carefully disconnect the wire harness from the old switch, release the locking tabs, and install the new one.
    6. Reassemble the dryer, restore power, and test its operation and confirm the error stays cleared during a full test cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WP3406107

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error 0E

    How to Fix Amana Dryer Error 0E

    Error Code: 0E Difficulty: Moderate

    Problem: Indicates that there is too much water in the appliance. This could be due to a blocked pump or a faulty hot water valve that is not shutting off.

    How to Fix 0E Error (Step-by-Step)

    1. Turn off the hot and cold water supply valves connected to the appliance.
    2. Unplug the dryer from the wall outlet to ensure safety.
    3. Check the drain hose at the back for any visible kinks, twists, or blockages that could restrict water flow.
    4. Place the end of the drain hose into a bucket to catch any trapped water and clear it from the line.
    5. Inspect the water inlet hoses for any signs of damage, wear, or leaks.
    6. This error often points to a faulty internal water pump or a stuck water inlet valve. These repairs involve handling water and electrical parts, so it is recommended to have a professional service service diagnose and complete the repair.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dryer Error -:–

    How to Fix Amana Dryer Error -:–

    Error Code: -:– Difficulty: Easy

    Problem: Dashes in the display can indicate a control panel issue or that the dryer is in a diagnostic mode. A power cycle is recommended.

    How to Fix -:– Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet or turn it off at the circuit breaker.
    2. Wait for 5 minutes to allow the internal electronics to fully discharge and reset.
    3. Plug the dryer back in or switch the circuit breaker on.
    4. Attempt to start a normal drying cycle to see if the code has been cleared.
    5. If the dashes reappear on the display, this indicates a more serious issue with the main control board.
    6. Due to the complexity and risk of working with electronic components, replacement of the control board should be performed by a qualified appliance service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error UL

    How to Fix Amana Washer Error UL

    Error Code: UL Difficulty: Hard

    Problem: Unbalanced Load

    How to Fix UL Error (Step-by-Step)

    1. Unplug the washer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Open the washer lid and redistribute the clothes evenly around the wash plate. Avoid washing single, heavy items by themselves.
    3. Close the lid and plug the washer back in. Try running a spin cycle. If the error persists, proceed to the next step.
    4. To inspect the suspension, you will need to lift the top panel of the washer. Use a putty knife to release the two clips on the front edge.
    5. With the top panel lifted, you can see the four suspension rods, one at each corner of the tub. Check if any of the rods appear broken or disconnected. Gently press down on the tub to see if it bounces excessively, which indicates weak suspension.
    6. To replace a suspension rod, lift the rod up from the tub bracket, then disconnect it from the top support cup. Install the new rod by reversing these steps.
    7. If the suspension rods are intact, the issue may be with the drive hub or gearcase, which typically requires a professional service.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10780048
    • W10821956
    • W11130362

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error RL

    How to Fix Amana Washer Error RL

    Error Code: RL Difficulty: Easy

    Problem: Items detected in the washer during the Clean Washer cycle.

    How to Fix RL Error (Step-by-Step)

    1. Press the ‘Pause’ or ‘Cancel’ button to stop the ‘Clean Washer’ cycle.
    2. Wait for the washer lid to unlock and confirm the error stays cleared during a full test cycle.
    3. Open the lid and remove any clothing or other items that were left inside the washer tub.
    4. Close the lid securely and confirm the error stays cleared during a full test cycle.
    5. Select the ‘Clean Washer’ cycle again and confirm the error stays cleared during a full test cycle.
    6. Press the ‘Start’ button to begin the cycle without any items in the tub.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error OL

    How to Fix Amana Washer Error OL

    Error Code: OL Difficulty: Easy

    Problem: Overload

    How to Fix OL Error (Step-by-Step)

    1. Press the ‘Cancel’ or ‘Power’ button to stop the washer.
    2. Open the washer door and look at the load. Items should be loosely packed and not crammed in.
    3. Remove several items to reduce the size of the load. A washer drum should not be filled more than three-quarters full.
    4. Redistribute the remaining items evenly around the wash plate or agitator to improve balance.
    5. Close the door and restart the cycle and confirm the error stays cleared during a full test cycle.
    6. For future loads, wash bulky items like comforters or blankets in smaller, separate loads.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error DRN

    How to Fix Amana Washer Error DRN

    Error Code: DRN Difficulty: Moderate

    Problem: Drain Error

    How to Fix DRN Error (Step-by-Step)

    1. First, check the drain hose at the back of the washer. Ensure it is not kinked, bent, or clogged.
    2. Make sure the drain hose is not inserted too far into the standpipe; it should only be about 4-5 inches in.
    3. Unplug the washer. You will need to access the drain pump, which is usually located behind a removable front panel at the bottom of the machine.
    4. Place a shallow pan and towels under the pump area to catch residual water. Slowly unscrew the pump’s filter cap to drain the remaining water.
    5. Clean the filter of any debris, such as lint, coins, or small clothing items.
    6. If the filter is clear and the hose is not blocked, the drain pump itself may have failed and will need to be replaced.
    7. To replace the pump, disconnect the hoses and the wire connector, remove the mounting screws, and install the new pump.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10276397
    • W10730972
    • WPW10730972

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error DU

    How to Fix Amana Washer Error DU

    Error Code: DU Difficulty: Easy

    Problem: Door Unlock Failure

    How to Fix DU Error (Step-by-Step)

    1. Press the ‘Cancel’ or ‘Power’ button to end the current cycle.
    2. Wait for 3-5 minutes. The washer’s control board needs time to process the cancel command and disengage the lock.
    3. If the door remains locked, unplug the washer from the wall outlet.
    4. Let the washer sit without power for at least 5 minutes.
    5. Plug the washer back in. The door should unlock after the machine powers on.
    6. Check for any small items that could be preventing the lock from disengaging properly.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes