Category: Amana

  • How to Fix Amana Washer Error DLO

    How to Fix Amana Washer Error DLO

    Error Code: DLO Difficulty: Hard

    Problem: Lid is not locking. This could be due to an obstruction or detergent buildup.

    How to Fix DLO Error (Step-by-Step)

    1. First, check for any clothing items, towels, or other obstructions that might be caught between the lid and the washer body, preventing it from closing properly.
    2. Unplug the washer from the power source and confirm the error stays cleared during a full test cycle.
    3. Clean the area around the lid lock and the strike with a damp cloth to remove any detergent or fabric softener buildup.
    4. Inspect the lid lock mechanism for any visible damage or signs of wear.
    5. If the area is clear and clean and the lock still won’t engage, the lid lock assembly likely needs to be replaced.
    6. To replace the lock, you will need to access it by removing the top console or panel of the washer. Disconnect the wire harness, remove the screws holding the old lock, and install the new one.
    7. Reassemble the washer, plug it in, and test the new lock by starting a cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10838613
    • W11253733
    • W11307244

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error DL

    How to Fix Amana Washer Error DL

    Error Code: DL Difficulty: Hard

    Problem: Door Lock Failure

    How to Fix DL Error (Step-by-Step)

    1. Unplug the washer from the electrical outlet to ensure safety.
    2. Wait at least 2-3 minutes to allow all electrical charge to dissipate.
    3. The door lock assembly is typically located behind the front panel of the washer, near the door opening. You may need to remove the top panel and/or the front panel to access it.
    4. Carefully inspect the wiring connecting to the door lock assembly. Look for any loose or damaged wires.
    5. If the wiring appears secure, the lock assembly itself is likely faulty and needs to be replaced.
    6. Disconnect the wiring harness from the old lock, remove the mounting screws, and install the new lock assembly in its place.
    7. Reassemble the washer panels, plug the machine back in, and test the door lock.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10838613
    • W11253733
    • W11307244

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error DET

    How to Fix Amana Washer Error DET

    Error Code: DET Difficulty: Easy

    Problem: Detergent cartridge not detected in the dispenser.

    How to Fix DET Error (Step-by-Step)

    1. Open the detergent dispenser drawer and confirm the error stays cleared during a full test cycle.
    2. Check to ensure the detergent cartridge is properly seated in its compartment.
    3. Remove the cartridge and inspect it for any clogs or blockages.
    4. Re-insert the cartridge firmly into the dispenser until you hear a click.
    5. Close the dispenser drawer and try starting the cycle again.
    6. If the issue persists, ensure you are using the correct type of detergent cartridge for your model.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error WASH LIGHT ON OR FLASHING

    How to Fix Amana Washer Error WASH LIGHT ON OR FLASHING

    Error Code: WASH LIGHT ON OR FLASHING Difficulty: Easy

    Problem: Washing

    How to Fix WASH LIGHT ON OR FLASHING Error (Step-by-Step)

    1. Do not be alarmed, this is not an error code. This light simply indicates that the washer is currently in the middle of a wash cycle.
    2. Allow the cycle to complete normally and confirm the error stays cleared during a full test cycle.
    3. The light will turn off once the washing cycle has finished.
    4. If you need to stop the cycle, press the ‘Cancel’ or ‘Power’ button.
    5. Wait for the machine to drain completely before attempting to open the door.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error SUD

    How to Fix Amana Washer Error SUD

    Error Code: SUD Difficulty: Easy

    Problem: Suds Detected

    How to Fix SUD Error (Step-by-Step)

    1. Do not add any more detergent. The washer will automatically attempt to resolve the suds issue.
    2. The machine will pause the cycle and may add extra rinses to clear the suds. This will extend the cycle time.
    3. Run a rinse and spin cycle to help clear the remaining suds.
    4. In the future, use only HE (High-Efficiency) detergent as recommended for your washer.
    5. Measure detergent carefully according to the load size and soil level to prevent over-sudsing.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error SPIN LIGHT FLASHING

    How to Fix Amana Washer Error SPIN LIGHT FLASHING

    Error Code: SPIN LIGHT FLASHING Difficulty: Hard

    Problem: Spinning

    How to Fix SPIN LIGHT FLASHING Error (Step-by-Step)

    1. Unplug the washer from the electrical outlet and confirm the error stays cleared during a full test cycle.
    2. Open the washer lid to access the lid lock assembly.
    3. Remove the screws holding the lid lock (Part W10810403) in place.
    4. Carefully disconnect the wire harness attached to the old lid lock.
    5. Connect the new lid lock to the wire harness and secure it with the screws.
    6. To address potential imbalance issues, also replace the four suspension rods (Part W10780048) at each corner of the tub.
    7. Plug the washer back in and start a spin cycle to test the new lid lock and suspension.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10810403

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error FANFRESH®

    How to Fix Amana Washer Error FANFRESH®

    Error Code: FANFRESH® Difficulty: Hard

    Problem: The FanFresh® option is activated, which periodically tumbles the load after the cycle ends to keep clothes fresh.

    How to Fix FANFRESH® Error (Step-by-Step)

    1. This is a feature, not an error. The FanFresh® light indicates the option is active, tumbling clothes after a cycle to keep them fresh. To stop it, simply press the Power or Cancel button.
    2. If this light appears without the option being selected, it may indicate a software glitch.
    3. Try resetting the machine by unplugging it from the power outlet for five minutes.
    4. Plug the washer back in and start a new cycle to see if the issue is resolved.
    5. A persistent, incorrect light could signal a deeper issue with the main control board or the drive motor.
    6. A service would need to test these components for electrical faults.
    7. Replacing either the control board or the main drive motor is a complex repair that involves significant disassembly of the appliance.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error SD

    How to Fix Amana Washer Error SD

    Error Code: SD Difficulty: Easy

    Problem: Suds Detected

    How to Fix SD Error (Step-by-Step)

    1. Pause the current wash cycle and confirm the error stays cleared during a full test cycle.
    2. Allow the washer some time (about 30 minutes) to break down the excess suds on its own.
    3. Once the suds have dissipated, resume the wash cycle and confirm the error stays cleared during a full test cycle.
    4. For future washes, ensure you are using a high-efficiency (HE) detergent.
    5. Reduce the amount of detergent used, especially for smaller or lightly soiled loads.
    6. Run an empty ‘Clean Washer’ cycle with a washing machine cleaner to remove any detergent residue.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error RINSE LIGHT ON

    How to Fix Amana Washer Error RINSE LIGHT ON

    Error Code: RINSE LIGHT ON Difficulty: Moderate

    Problem: Rinsing

    How to Fix RINSE LIGHT ON Error (Step-by-Step)

    1. Unplug the washer and turn off the hot and cold water supply valves.
    2. Disconnect the water inlet hoses from the back of the machine.
    3. Remove the screws on the back panel to access the water inlet valve (Part W11220230).
    4. Take note of the electrical connections on the old valve before disconnecting them.
    5. Squeeze the clamps on the internal water hoses and slide them off the valve nozzles.
    6. Remove the screws holding the old valve in place and install the new one.
    7. Reconnect the hoses and electrical connections, then turn on the water and power to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F7E5

    How to Fix Amana Washer Error F7E5

    Error Code: F7E5 Difficulty: Hard

    Problem: Shifter fault.

    How to Fix F7E5 Error (Step-by-Step)

    1. Disconnect the washer from the electrical outlet to ensure your safety.
    2. Shut off the hot and cold water faucets that supply the washing machine.
    3. Lean the washer back against a wall to get access to the components underneath.
    4. Find the shifter/actuator, which is a small motor assembly mounted to the bottom of the wash tub.
    5. Unplug the electrical connector from the actuator and remove the mounting screws.
    6. Swap the old actuator with the new one, making sure to secure it with the screws and reconnect the wiring.
    7. Carefully set the washer upright, reconnect the power and water, and test its operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes