Author: ApplianceFixGuide Team

  • How to Fix Bosch Washer Error E02

    How to Fix Bosch Washer Error E02

    Error Code: E02 Difficulty: Hard

    Problem: Motor fault.

    How to Fix E02 Error (Step-by-Step)

    1. Disconnect the washer from the power outlet to ensure safety.
    2. Access the rear of the machine by unscrewing and removing the back panel.
    3. Locate the drive motor at the bottom of the drum.
    4. Carefully inspect the wiring harness connected to the motor. Ensure the plug is securely seated and that no wires are loose, burnt, or damaged.
    5. Identify the carbon brushes on the motor. They are small, rectangular blocks that contact the motor’s commutator.
    6. Unscrew the brush holders and gently remove the carbon brushes. If they are worn down to less than a quarter of an inch, they need to be replaced.
    7. If the wiring and brushes are in good condition, the motor itself may be faulty and require replacement.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E06

    How to Fix Bosch Washer Error E06

    Error Code: E06 Difficulty: Moderate

    Problem: Door is not closed.

    How to Fix E06 Error (Step-by-Step)

    1. First, ensure the washer door is completely closed and that no clothing is caught between the door and the seal.
    2. Unplug the washing machine from the electrical outlet for safety.
    3. Open the door and inspect the door latch mechanism on the door itself and the door strike on the washer body. Look for any visible signs of damage, cracks, or foreign objects.
    4. Examine the door hinge for any looseness or damage that could prevent proper alignment.
    5. To inspect the door lock assembly, you will need to peel back the door boot seal from the front panel around the lock area.
    6. Unscrew the two screws holding the door lock assembly in place and carefully pull it out.
    7. Check the electrical connections to the door lock. If they appear secure and the lock shows no physical damage, the lock assembly itself may have failed and needs to be replaced.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 00425059
    • 00605590
    • 00613824

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E10

    How to Fix Bosch Washer Error E10

    Error Code: E10 Difficulty: Easy

    Problem: Blocked pump.

    How to Fix E10 Error (Step-by-Step)

    1. Press the ‘Start/Pause’ button to stop the current cycle.
    2. Locate the small service flap at the bottom front of the washer.
    3. Place a shallow tray and a towel underneath the flap to catch residual water.
    4. Carefully open the flap. You will see a drain hose and a large filter cap.
    5. Slowly unscrew the filter cap, allowing the water to drain out completely into the tray.
    6. Once drained, fully remove the cap and inspect the filter and the pump housing for any blockages like lint, coins, or other debris. Clear any obstructions you find.
    7. Screw the filter cap back on tightly, secure the drain hose, and close the service flap.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E16

    How to Fix Bosch Washer Error E16

    Error Code: E16 Difficulty: Moderate

    Problem: Door is open or not locked properly.

    How to Fix E16 Error (Step-by-Step)

    1. Firmly close the washer door to ensure it is latched. Listen for a distinct ‘click’.
    2. Check for any laundry items that might be caught in the door, preventing it from closing properly.
    3. Unplug the washer from the power source and confirm the error stays cleared during a full test cycle.
    4. Open the door and carefully examine the plastic door hook and the metal door strike for any signs of breakage or misalignment.
    5. To access the door lock mechanism, carefully pull back the rubber door seal around the lock area.
    6. Remove the screws that secure the door lock assembly to the front panel.
    7. Gently pull the lock out and check the wiring connector. If the connection is secure and there’s no visible damage, the door lock assembly likely needs to be replaced.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 00618716

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E17

    How to Fix Bosch Washer Error E17

    Error Code: E17 Difficulty: Moderate

    Problem: Water supply error; pump time has exceeded its limits.

    How to Fix E17 Error (Step-by-Step)

    1. Ensure that the water supply faucets connected to the washer are fully turned on.
    2. Pull the washer away from the wall to inspect the water inlet hoses. Make sure they are not kinked, bent, or crushed.
    3. Turn off the water supply faucets and unscrew the inlet hoses from the back of the washer.
    4. Check the small filter screens inside the hose connections and at the washer’s water inlet valve ports. Clean any sediment or debris found.
    5. Reconnect the hoses securely and turn the water back on, checking for leaks.
    6. If the error persists, the water inlet valve, which electrically controls water flow, may be faulty and require replacement.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 00422244
    • 00428210

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E18

    How to Fix Bosch Washer Error E18

    Error Code: E18 Difficulty: Moderate

    Problem: Drainage Error; blockage in the filter or drainage system.

    How to Fix E18 Error (Step-by-Step)

    1. Begin by cleaning the drain pump filter, which is located behind the service flap at the bottom front of the washer. Place a towel and a shallow dish below it to catch water before unscrewing the filter cap.
    2. Remove any lint, coins, or other debris from the filter and the pump cavity.
    3. Inspect the main drain hose at the back of the machine for any kinks or sharp bends that could restrict water flow.
    4. Disconnect the drain hose from the household drain pipe and check for any clogs at the connection point or within the hose itself.
    5. If the filter and hose are clear, the blockage may be in the internal sump hose connecting the tub to the pump. This requires removing the front or back panel for access.
    6. If all hoses are clear, the drain pump itself may have failed and will need to be replaced.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E20

    How to Fix Bosch Washer Error E20

    Error Code: E20 Difficulty: Hard

    Problem: Unexpected heating during the cycle.

    How to Fix E20 Error (Step-by-Step)

    1. Disconnect the washer from both the power outlet and the water supply.
    2. Locate the heating element, which is typically found at the bottom of the washtub.
    3. Carefully disconnect the wires attached to the heating element terminals.
    4. Remove the nuts or screws that are securing the heating element in place.
    5. Gently pull the old heating element out of its housing. You may need to wiggle it slightly to release it from the seal.
    6. Insert the new heating element, ensuring the rubber seal is properly seated to prevent leaks.
    7. Reconnect the wiring and securely fasten the new element with the original nuts or screws.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E23

    How to Fix Bosch Washer Error E23

    Error Code: E23 Difficulty: Easy

    Problem: AquaStop Hose has been activated; indicates a leak.

    How to Fix E23 Error (Step-by-Step)

    1. Unplug the washing machine from the power source immediately and confirm the error stays cleared during a full test cycle.
    2. Turn off the water supply to the washer at the wall valves.
    3. Inspect the base of the machine for any visible signs of water leakage.
    4. Check the AquaStop hose connections at both the tap and the machine to ensure they are tight.
    5. Tilt the machine slightly to drain any water that may have collected in the base pan, which can trigger the sensor.
    6. After ensuring there are no active leaks and the base is dry, plug the machine back in and turn on the water supply.
    7. Run a short test cycle to confirm the error is cleared and no new leaks appear.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E25

    How to Fix Bosch Washer Error E25

    Error Code: E25 Difficulty: Easy

    Problem: Turbidity sensor issue.

    How to Fix E25 Error (Step-by-Step)

    1. Cancel the current wash cycle and drain the water from the machine.
    2. Clean the drain pump filter, which is usually located behind a small door at the bottom front of the washer.
    3. Remove any lint, debris, or foreign objects that may be obstructing the filter.
    4. Check the drain hose for any kinks or blockages that could be affecting the water drainage.
    5. Run a cleaning cycle with a washing machine cleaner to remove any residue from the turbidity sensor.
    6. Ensure you are using the correct amount and type of detergent for your water hardness and load size.
    7. Restart the washer on a new cycle to see if the issue is resolved.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error E26

    How to Fix Bosch Washer Error E26

    Error Code: E26 Difficulty: Hard

    Problem: Analogue pressure sensor issue.

    How to Fix E26 Error (Step-by-Step)

    1. Turn off the washer and unplug it from the electrical outlet.
    2. Access the analogue pressure sensor, which is usually located at the top of the machine, connected to a thin tube.
    3. Disconnect the electrical connector from the sensor carefully and confirm the error stays cleared during a full test cycle.
    4. Detach the pressure tube from the sensor. Be gentle to avoid damaging the tube.
    5. Remove the screws or clips holding the sensor in place and take out the old sensor.
    6. Install the new analogue pressure sensor and secure it with the screws or clips.
    7. Reattach the pressure tube and the electrical connector, then reassemble the washer panels.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.