Author: ApplianceFixGuide Team

How to Fix Bosch Refrigerator Error E21
Error Code: E21 Difficulty: Hard

Problem: Communication error between the display control module and the ice and water dispenser control module.

How to Fix E21 Error (Step-by-Step)
1. Unplug the refrigerator from the wall outlet to ensure your safety.
2. Attempt a system reset by leaving the refrigerator unplugged for 10-15 minutes to allow the internal electronics to discharge, then plug it back in. If the error persists, proceed to the next step.
3. Access the display control module, which is typically located behind the main user interface on the exterior of the refrigerator door. This may require carefully prying off a plastic cover or removing a few screws.
4. Locate the ice and water dispenser control module, usually found inside the dispenser housing itself. You will likely need to remove the dispenser drip tray and front panel to access it.
5. Carefully inspect the wiring harness that connects the display module to the dispenser module. Look for any pinched, frayed, or disconnected wires. Securely reconnect any loose plugs you find.
6. If the wiring appears intact, one of the control modules has likely failed. It is recommended to replace the dispenser control module first. Disconnect the wire connectors from the old module, remove it from its mounting, and install the new one in its place.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Bosch refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Bosch refrigerator temperature sensor
  
  Common replacement category: Temperature sensor / thermistor
  
  Fit note: Exact OEM part number varies by full Bosch refrigerator model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for temperature, alarm, and cooling-sensor faults after the door seal, vents, and settings are checked.
  
  Search Amazon for Bosch refrigerator temperature sensor
- Bosch refrigerator evaporator fan motor
  
  Common replacement category: Evaporator fan motor
  
  Fit note: Exact OEM part number varies by full Bosch refrigerator model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for airflow, fan, and uneven-cooling symptoms after ice buildup and obstructions are ruled out.
  
  Search Amazon for Bosch refrigerator evaporator fan motor
- Bosch refrigerator electronic control board
  
  Common replacement category: Main electronic control board
  
  Fit note: Exact OEM part number varies by full Bosch refrigerator model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for repeated electronic, display, or cooling-control faults after connectors and power are checked.
  
  Search Amazon for Bosch refrigerator electronic control board
Before ordering: match the part to the complete Bosch refrigerator model number on the appliance tag.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.
- [OK]Water inlet valve, ice maker, or fan failures keep returning
- [OK]Defrost heater, thermostat, or sensor faults stack up
- [OK]Compressor or sealed-system repair is not economical
- [OK]Food-loss risk is becoming a pattern
Recommended Refrigerator Replacement Options
Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators
As an Amazon Associate, we earn from qualifying purchases.
Browse all Bosch error codes: Bosch Error Codes
May 13, 2026
How to Fix Bosch Dishwasher Error WATER TAP SYMBOL
Error Code: WATER TAP SYMBOL Difficulty: Hard

Problem: Problem with the water supply.

How to Fix WATER TAP SYMBOL Error (Step-by-Step)
1. Turn off the power to the dishwasher at your circuit breaker and shut off the water supply valve, which is usually located under the sink.
2. Check the water supply hose for any kinks or sharp bends that could be restricting water flow. Straighten the hose if necessary.
3. Unscrew the water supply hose from the dishwasher’s water inlet valve. Place a towel underneath to catch any residual water. Check the small filter screen inside the valve for any debris or sediment and clean it with a small brush and water.
4. If the filter is clean and the hose is not kinked, the water inlet valve itself may be faulty. This part is located at the front, typically behind the bottom kick plate.
5. To replace the valve, disconnect the power clip and the water supply line. Remove the two screws holding it in place. Install the new valve by securing it with the screws, reattaching the water line, and plugging in the power clip.
6. If replacing the inlet valve does not solve the issue, the problem could be with the main water inlet assembly, which is a more complex component inside the dishwasher.
7. After performing the repairs, reconnect the main water supply hose, turn the water and power back on, and run a test cycle to ensure the dishwasher fills with water correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Bosch dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.
  
  Search Amazon for Bosch dishwasher water inlet valve
- Bosch dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.
  
  Search Amazon for Bosch dishwasher drain pump
- Bosch dishwasher circulation pump
  
  Common replacement category: Circulation pump / wash motor
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.
  
  Search Amazon for Bosch dishwasher circulation pump
Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
May 13, 2026
How to Fix Bosch Dishwasher Error WASHING SYMBOL
Error Code: WASHING SYMBOL Difficulty: Easy

Problem: Indicates that the main wash portion of the cycle is currently active.

How to Fix WASHING SYMBOL Error (Step-by-Step)
1. No action is needed and confirm the error stays cleared during a full test cycle.
2. This symbol simply means your dishwasher is in the middle of a wash cycle.
3. Wait for the cycle to complete and confirm the error stays cleared during a full test cycle.
4. The light will turn off once the washing and drying process is finished.
5. You can then open the door and unload your clean dishes.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Bosch dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.
  
  Search Amazon for Bosch dishwasher water inlet valve
- Bosch dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.
  
  Search Amazon for Bosch dishwasher drain pump
- Bosch dishwasher circulation pump
  
  Common replacement category: Circulation pump / wash motor
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.
  
  Search Amazon for Bosch dishwasher circulation pump
Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.
What to Check Next on This Bosch Dishwasher

Bosch dishwasher symptom: Use the symbol or code as a starting point, then match the repair path to what the dishwasher is actually doing.
1. Confirm whether the display is a normal cycle/status symbol or a recurring fault that stops operation.
2. Check water supply, filter, sump, spray arms, drain path, and door latch before replacing electronic parts.
3. If the same problem returns after basic checks, inspect the matching sensor, pump, heater, wiring, or control path based on the symptom.
If the symptom returns after these checks, use the full Bosch model number from the door tag before ordering any part. The same display message can point to different parts depending on the exact model and what the dishwasher does during fill, wash, drain, or dry.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
May 13, 2026
How to Fix Bosch Dishwasher Error VARIOSPEED PLUS SYMBOL
Error Code: VARIOSPEED PLUS SYMBOL Difficulty: Easy

Problem: An option that can reduce the cleaning time of a cycle significantly while maintaining cleaning and drying performance.

How to Fix VARIOSPEED PLUS SYMBOL Error (Step-by-Step)
1. Find the VarioSpeed Plus symbol on the control panel. This is a selectable option, not an error code.
2. Understand that this function is designed to reduce the duration of most wash cycles by up to 66% while still delivering excellent cleaning and drying results.
3. To use this feature, first choose a primary wash program like Auto, Normal, or Heavy Duty.
4. After selecting the main program, press the VarioSpeed Plus button. The symbol will light up to indicate it is active.
5. Be aware that in order to achieve the same cleaning results in less time, the dishwasher will use more water and energy.
6. Press the Start button to begin the accelerated cycle. The new, shorter remaining time will be shown on the display.
7. If you prefer to run the standard, more economical cycle, simply do not press the VarioSpeed Plus button after selecting your program.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Bosch Dishwasher

Bosch Dishwasher Error VARIOSPEED PLUS SYMBOL: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
2. 2. Confirm whether the display is a normal option/status indicator or a recurring fault that interrupts filling, washing, draining, drying, locking, or controls.
3. 3. Treat VarioSpeed Plus as a cycle option/status symbol first: confirm it is selected intentionally, cancel the option if needed, then diagnose only if the light is stuck, the program will not respond, or cycle timing becomes abnormal.
4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
5. 5. Run a short test cycle and watch the exact stage where the symptom returns; the stage matters more than the label by itself.
6. 6. Replace a part only after the same symptom repeats and model-specific checks point to that part category. Match any replacement to the complete Bosch dishwasher model number on the door tag.
If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the appliance tag. The same display clue can point to different components depending on the exact model and when the failure appears.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Bosch dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.
  
  Search Amazon for Bosch dishwasher water inlet valve
- Bosch dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.
  
  Search Amazon for Bosch dishwasher drain pump
- Bosch dishwasher circulation pump
  
  Common replacement category: Circulation pump / wash motor
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.
  
  Search Amazon for Bosch dishwasher circulation pump
Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
May 13, 2026
How to Fix Bosch Dishwasher Error TIMELIGHT
Error Code: TIMELIGHT Difficulty: Easy

Problem: A feature on fully integrated models that projects the remaining cycle time and status onto the floor.

How to Fix TIMELIGHT Error (Step-by-Step)
1. Observe the time and status information projected onto the floor in front of your fully integrated dishwasher.
2. Understand that this feature, called TimeLight, is a normal part of the dishwasher’s operation and not an error.
3. The projection provides useful information that is otherwise hidden, such as the remaining time in the wash cycle, the current cycle stage (e.g., washing, rinsing, drying), or other status symbols.
4. There is no action required to turn this feature on or off; it operates automatically whenever a wash cycle is running.
5. The projection will disappear from the floor once the cycle is completely finished and the dishwasher is ready to be unloaded.
6. This feature is only present on specific high-end, fully-integrated Bosch models.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Bosch dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.
  
  Search Amazon for Bosch dishwasher water inlet valve
- Bosch dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.
  
  Search Amazon for Bosch dishwasher drain pump
- Bosch dishwasher circulation pump
  
  Common replacement category: Circulation pump / wash motor
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.
  
  Search Amazon for Bosch dishwasher circulation pump
Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.
What to Check Next on This Bosch Dishwasher

Bosch Dishwasher Error TIMELIGHT: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.
If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
May 13, 2026
How to Fix Bosch Dishwasher Error SILENCE/NIGHT MODE SYMBOL
Error Code: SILENCE/NIGHT MODE SYMBOL Difficulty: Easy

Problem: A program that reduces the noise level of the dishwasher by using a lower spray pressure and an extended cleaning phase.

How to Fix SILENCE/NIGHT MODE SYMBOL Error (Step-by-Step)
1. Locate the Silence or Night Mode symbol on your dishwasher’s control panel, often represented by a moon or a ‘shushing’ face icon.
2. Recognize this as a selectable wash program designed to operate at a lower noise level, ideal for running at night or in open-plan living spaces.
3. To use this mode, press the power button and then select the Silence/Night Mode program.
4. Load your dishwasher and add detergent as you would for a normal cycle.
5. Close the door and press Start. The dishwasher will run using a lower spray pressure and extended cycle time to minimize noise.
6. Note that while the cycle is quieter, it will take longer to complete than a standard program.
7. To return to normal operation for your next load, simply select a different wash program (e.g., Auto, Normal) instead of the Silence/Night Mode.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Bosch dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.
  
  Search Amazon for Bosch dishwasher water inlet valve
- Bosch dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.
  
  Search Amazon for Bosch dishwasher drain pump
- Bosch dishwasher circulation pump
  
  Common replacement category: Circulation pump / wash motor
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.
  
  Search Amazon for Bosch dishwasher circulation pump
Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.
What to Check Next on This Bosch Dishwasher

Bosch Dishwasher Error SILENCE/NIGHT MODE SYMBOL: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.
If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
May 13, 2026
How to Fix Bosch Dishwasher Error SHINE & DRY SYMBOL
Error Code: SHINE & DRY SYMBOL Difficulty: Easy

Problem: An option that uses more water during the rinse cycle and extends the drying phase to prevent watermarks and improve drying results.

How to Fix SHINE & DRY SYMBOL Error (Step-by-Step)
1. Notice the Shine & Dry symbol on the control panel. This is an optional setting you can select, not an error message.
2. Understand that this function improves the drying performance, especially for plastics, and enhances the shine on glassware.
3. To activate this option, first select your desired main wash program (e.g., Auto, Normal, Heavy).
4. Before starting the cycle, press the button corresponding to the Shine & Dry symbol. An indicator light will usually confirm it has been selected.
5. Be aware that selecting this option will increase the final rinse temperature and extend the drying phase, which may increase the overall cycle time and energy consumption.
6. If you do not need enhanced drying for a particular load, simply do not select the option after choosing your main program.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Bosch dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.
  
  Search Amazon for Bosch dishwasher water inlet valve
- Bosch dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.
  
  Search Amazon for Bosch dishwasher drain pump
- Bosch dishwasher circulation pump
  
  Common replacement category: Circulation pump / wash motor
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.
  
  Search Amazon for Bosch dishwasher circulation pump
Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.
What to Check Next on This Bosch Dishwasher

Bosch Dishwasher Error SHINE & DRY SYMBOL: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
3. 3. Start with the heat and temperature path: water circulation, heater circuit, NTC sensor, wiring, and control output.
4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.
If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
May 13, 2026
How to Fix Bosch Dishwasher Error SALT SYMBOL (S-SHAPED ARROWS)
Error Code: SALT SYMBOL (S-SHAPED ARROWS) Difficulty: Easy

Problem: The dishwasher salt reservoir needs to be refilled.

How to Fix SALT SYMBOL (S-SHAPED ARROWS) Error (Step-by-Step)
1. Identify the Salt symbol, which looks like two S-shaped arrows, lit up on the control panel. This means the water softener needs more dishwasher salt.
2. Open the dishwasher door and pull out the bottom rack completely to access the floor of the dishwasher tub.
3. Locate the salt reservoir cap, which is a large, round cap, and unscrew it by turning it counter-clockwise.
4. If this is the first time you are adding salt, you must first fill the reservoir with about 1 liter of water.
5. Place the funnel that came with your dishwasher into the opening. Slowly pour in dishwasher-specific salt until the reservoir is full.
6. Remove the funnel and clean any excess salt from around the opening. Screw the cap back on tightly in a clockwise direction.
7. Run a short rinse or wash cycle immediately after refilling the salt to wash away any spilled salt granules and to activate the softener.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Bosch dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.
  
  Search Amazon for Bosch dishwasher water inlet valve
- Bosch dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.
  
  Search Amazon for Bosch dishwasher drain pump
- Bosch dishwasher circulation pump
  
  Common replacement category: Circulation pump / wash motor
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.
  
  Search Amazon for Bosch dishwasher circulation pump
Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.
What to Check Next on This Bosch Dishwasher

Salt symbol: The salt indicator is tied to the water-softening system. It usually needs refill or setting checks before parts are considered.
1. Refill the salt reservoir with dishwasher salt only, then wipe spilled salt from the tub before running a rinse or short cycle.
2. Check the water hardness setting if the light returns quickly or dishes show film despite enough salt.
3. If the reservoir is full but the symbol never clears, inspect the cap, float or sensor area, wiring, and control input before replacing parts.
If the symptom returns after these checks, use the full Bosch model number from the door tag before ordering any part. The same display message can point to different parts depending on the exact model and what the dishwasher does during fill, wash, drain, or dry.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
May 13, 2026
How to Fix Bosch Dishwasher Error RINSE AID SYMBOL (SUN/STARBURST)
Error Code: RINSE AID SYMBOL (SUN/STARBURST) Difficulty: Easy

Problem: The rinse aid dispenser needs to be refilled.

How to Fix RINSE AID SYMBOL (SUN/STARBURST) Error (Step-by-Step)
1. Locate the Rinse Aid symbol, which looks like a sun or starburst, illuminated on your dishwasher’s display. This indicates the rinse aid level is low.
2. Open the dishwasher door completely. Find the rinse aid dispenser, which is a round compartment typically located next to the main detergent dispenser on the inside of the door.
3. Turn the dispenser cap counter-clockwise to open it. Some models may have a lid that flips open instead.
4. Slowly pour liquid rinse aid into the opening until the indicator window or level gauge shows it is full. Be careful not to overfill.
5. Wipe up any spilled rinse aid with a cloth to prevent excess foaming during the next wash cycle.
6. Securely close the dispenser by replacing the cap and turning it clockwise until it locks, or by snapping the lid shut.
7. The illuminated symbol on the display will turn off after the next wash cycle begins.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Bosch dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.
  
  Search Amazon for Bosch dishwasher water inlet valve
- Bosch dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.
  
  Search Amazon for Bosch dishwasher drain pump
- Bosch dishwasher circulation pump
  
  Common replacement category: Circulation pump / wash motor
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.
  
  Search Amazon for Bosch dishwasher circulation pump
Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.
What to Check Next on This Bosch Dishwasher

Bosch Dishwasher Error RINSE AID SYMBOL (SUN/STARBURST): Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.
If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
May 13, 2026
How to Fix Bosch Dishwasher Error RED LIGHT ON FLOOR (INFOLIGHT)
Error Code: RED LIGHT ON FLOOR (INFOLIGHT) Difficulty: Easy

Problem: The dishwasher is currently operating.

How to Fix RED LIGHT ON FLOOR (INFOLIGHT) Error (Step-by-Step)
1. Observe the steady red light projected onto the floor below your dishwasher.
2. Recognize that this light, known as InfoLight, is a normal operational feature and not an error indicator.
3. Understand that the red light’s purpose is to show that a wash cycle is currently in progress. This is especially useful for fully integrated models where the control panel is not visible.
4. Do not attempt to open the dishwasher while this light is on, as hot water and steam may be released.
5. Wait for the wash and dry cycle to complete. The red light will automatically turn off once the cycle has finished.
6. Once the light is off, it is safe to open the dishwasher and unload your clean dishes.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Bosch dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.
  
  Search Amazon for Bosch dishwasher water inlet valve
- Bosch dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.
  
  Search Amazon for Bosch dishwasher drain pump
- Bosch dishwasher circulation pump
  
  Common replacement category: Circulation pump / wash motor
  
  Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
  
  Confidence: Medium
  This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.
  
  Search Amazon for Bosch dishwasher circulation pump
Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.
What to Check Next on This Bosch Dishwasher

Bosch Dishwasher Error RED LIGHT ON FLOOR (INFOLIGHT): Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.
1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.
If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
May 13, 2026