Author: ApplianceFixGuide Team

  • How to Fix Amana Washer Error SUD

    How to Fix Amana Washer Error SUD

    Error Code: SUD Difficulty: Easy

    Problem: Suds Detected

    How to Fix SUD Error (Step-by-Step)

    1. Do nothing. The washer will automatically attempt to remove the excess suds.
    2. Wait for the cycle to complete. This may take longer than usual as the machine works to clear the foam.
    3. Once the cycle is finished, remove the laundry and confirm the error stays cleared during a full test cycle.
    4. Run an empty rinse cycle to clear any remaining suds from the tub.
    5. In the future, use less detergent, especially with soft water or lightly soiled loads. Always use High-Efficiency (HE) detergent.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error WASH LIGHT ON OR FLASHING

    How to Fix Amana Washer Error WASH LIGHT ON OR FLASHING

    Error Code: WASH LIGHT ON OR FLASHING Difficulty: Hard

    Problem: Washing

    How to Fix WASH LIGHT ON OR FLASHING Error (Step-by-Step)

    1. Unplug the washer from the wall outlet and turn off both the hot and cold water faucets.
    2. Pull the washer away from the wall to access the back panel.
    3. Use a screwdriver or nut driver to remove the screws securing the top or back panel.
    4. Locate the water inlet valve where the water hoses connect to the washer.
    5. Disconnect the electrical wire harnesses from the valve solenoids and unscrew the hoses.
    6. Remove the screws holding the valve in place and install the new valve.
    7. Reconnect the hoses and wire harnesses, re-secure the back panel, turn on the water, and plug the washer in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W11096268 (Water Inlet Valve)
    • W11220230 (Water Inlet Valve)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error DET

    How to Fix Amana Washer Error DET

    Error Code: DET Difficulty: Easy

    Problem: Detergent cartridge not detected in the dispenser.

    How to Fix DET Error (Step-by-Step)

    1. Open the detergent dispenser drawer completely and confirm the error stays cleared during a full test cycle.
    2. Remove the detergent cartridge from the dispenser and confirm the error stays cleared during a full test cycle.
    3. Check the cartridge for any damage or blockage and confirm the error stays cleared during a full test cycle.
    4. Ensure there is no debris or obstruction in the dispenser housing where the cartridge sits.
    5. Re-insert the cartridge firmly into the dispenser until you hear it click into place.
    6. Close the dispenser drawer and try starting a new cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error DL

    How to Fix Amana Washer Error DL

    Error Code: DL Difficulty: Moderate

    Problem: Door Lock Failure

    How to Fix DL Error (Step-by-Step)

    1. Disconnect the washer from its power source and confirm the error stays cleared during a full test cycle.
    2. Open the washer lid. You may need to use a putty knife to release the clips holding the top panel down.
    3. Locate the lid lock assembly on the underside of the top panel.
    4. Disconnect the wire harness connected to the lid lock and confirm the error stays cleared during a full test cycle.
    5. Remove the screws that secure the old lid lock assembly to the washer’s top.
    6. Install the new lid lock assembly, making sure it is properly aligned, and secure it with the screws.
    7. Reconnect the wire harness, lower the top panel, and restore power to the washer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10838613 (Lid Lock Assembly)
    • W11307244 (Lid Lock Assembly)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error DU

    How to Fix Amana Washer Error DU

    Error Code: DU Difficulty: Easy

    Problem: Door Unlock Failure

    How to Fix DU Error (Step-by-Step)

    1. Press the ‘Pause’ or ‘Cancel’ button to try and unlock the door.
    2. Wait for 5-10 minutes, as the washer may have a time-delay feature for safety.
    3. If the door remains locked, unplug the washer from the power outlet for at least 5 minutes.
    4. Plug the washer back in. This power cycle may reset the control board and release the lock.
    5. Check for any clothing items that might be caught in the door latch, preventing it from opening.
    6. Try running a ‘Drain & Spin’ cycle to see if completing a cycle will unlock the door.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error DRN

    How to Fix Amana Washer Error DRN

    Error Code: DRN Difficulty: Hard

    Problem: Drain Error

    How to Fix DRN Error (Step-by-Step)

    1. Unplug the washer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Place towels on the floor and have a shallow pan or bucket ready to catch water.
    3. Locate the drain pump, usually accessible through the front lower panel or by tilting the machine.
    4. Disconnect the hoses from the pump, allowing any trapped water to drain into your pan.
    5. Disconnect the electrical wires from the pump and confirm the error stays cleared during a full test cycle.
    6. Remove the screws or release the tabs holding the old pump in place and remove it.
    7. Install the new drain pump, reconnect the hoses and wires, and secure the access panel before restoring power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10919003 (Drain Pump)
    • WPW10730972 (Drain Pump)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error OL

    How to Fix Amana Washer Error OL

    Error Code: OL Difficulty: Easy

    Problem: Overload

    How to Fix OL Error (Step-by-Step)

    1. Press the ‘Pause’ or ‘Cancel’ button to stop the cycle.
    2. Open the washer lid and remove several items to reduce the weight of the load.
    3. Redistribute the remaining clothes evenly around the wash plate or agitator.
    4. Ensure the load is balanced and not clumped to one side.
    5. Close the lid and restart the cycle and confirm the error stays cleared during a full test cycle.
    6. For future loads, avoid washing single heavy items and ensure you don’t pack the washer too tightly.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error RL

    How to Fix Amana Washer Error RL

    Error Code: RL Difficulty: Easy

    Problem: Items detected in the washer during the Clean Washer cycle.

    How to Fix RL Error (Step-by-Step)

    1. Press the ‘Pause’ or ‘Cancel’ button to stop the Clean Washer cycle.
    2. Wait for the lid to unlock, which may take a moment.
    3. Open the washer lid and look inside the drum and confirm the error stays cleared during a full test cycle.
    4. Remove any clothing, towels, or other items that were left inside.
    5. Close the lid securely and confirm the error stays cleared during a full test cycle.
    6. Select the ‘Clean Washer’ cycle again and confirm the error stays cleared during a full test cycle.
    7. Press the ‘Start’ button to run the cycle with a completely empty drum.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error UL

    How to Fix Amana Washer Error UL

    Error Code: UL Difficulty: Easy

    Problem: Unbalanced Load

    How to Fix UL Error (Step-by-Step)

    1. The washer has paused automatically. Press the ‘Pause’ or ‘Cancel’ button to ensure the cycle is stopped.
    2. Wait for the spinning to stop completely and for the lid to unlock.
    3. Open the lid and observe the clothes inside. They are likely gathered on one side of the drum.
    4. If washing one large or absorbent item, add a couple of towels to help balance the weight.
    5. Close the lid firmly and confirm the error stays cleared during a full test cycle.
    6. Press the ‘Start’ button to resume the cycle. The washer will attempt to spin again.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Washer Error CL

    How to Fix Bosch Washer Error CL

    Error Code: CL Difficulty: Easy

    Problem: Child Lock Activated.

    How to Fix CL Error (Step-by-Step)

    1. Locate the ‘Child Lock’ button on your washer’s control panel. It is often indicated by a key symbol or labeled clearly.
    2. Press and hold the ‘Child Lock’ button for 3 to 5 seconds.
    3. Observe the display panel. The child lock symbol (usually a key) should disappear, indicating it has been deactivated.
    4. If the symbol persists, try pressing and holding the ‘Spin’ and ‘Finish in’ buttons simultaneously for about 3 seconds.
    5. Once deactivated, you should be able to open the door and operate the washer normally.
    6. Test the functionality by attempting to start a new cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.