Author: ApplianceFixGuide Team

Error Code: ER Difficulty: Hard

Problem: Membrane switch failure.

How to Fix ER Error (Step-by-Step)

1. Unplug the dryer from the wall outlet to ensure your safety by completely disconnecting the power.
2. Remove the screws securing the top panel of the dryer, which are typically located at the back or on the sides. Lift the top panel off to access the control console.
3. Carefully take photos of the wire connections to the main control board for reference. Locate the thin, flat ribbon cable that connects the membrane switch to the control board and gently unplug it.
4. Remove the control knob if present, and then unscrew the main control board and its housing from the front console. This will expose the back of the membrane switch keypad.
5. The old membrane switch is attached with adhesive. Carefully peel the old, faulty keypad off the front of the control console. Clean any residue off the surface before applying the new one.
6. Align the new membrane switch carefully with the button cutouts on the console and press it firmly into place. Re-secure the control board and its housing, then reconnect the ribbon cable to the board.
7. Reassemble the dryer by securing the top panel with its screws. Plug the dryer back into the power outlet and run a test cycle to confirm that the new keypad is working correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: EHE Difficulty: Hard

Problem: A safety line alarm has been triggered, indicating a faulty main board.

How to Fix EHE Error (Step-by-Step)

1. Turn off the circuit breaker for the dryer and confirm the error stays cleared during a full test cycle.
2. Remove the top panel of the dryer to get to the main control board.
3. Take a picture of the wire connections to the board for reference.
4. Disconnect all the wires from the old control board and confirm the error stays cleared during a full test cycle.
5. Remove the screws that are holding the control board in place.
6. Put the new main control board in and secure it with the screws.
7. Reconnect all the wires according to the picture you took and reassemble the dryer.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: EF8 Difficulty: Moderate

Problem: Stuck key on the user interface.

How to Fix EF8 Error (Step-by-Step)

1. Unplug the dryer from the wall outlet and confirm the error stays cleared during a full test cycle.
2. Use a soft cloth and a mild cleaner to wipe down the user interface and buttons.
3. Check for any debris or sticky residue around the buttons that might be causing them to stick.
4. Gently press each button to ensure it moves freely and doesn’t get stuck.
5. If a button is still stuck, you may need to replace the user interface control board.
6. To do this, you will need to remove the top panel of the dryer to access the board.
7. Disconnect the wiring and replace the old board with the new one.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: EF6 Difficulty: Hard

Problem: Control reset.

How to Fix EF6 Error (Step-by-Step)

1. Disconnect the dryer from the power source and confirm the error stays cleared during a full test cycle.
2. Remove the top panel of the dryer to access the main control board.
3. Carefully disconnect all the wire harnesses connected to the control board.
4. Remove the screws holding the control board in place and take out the old board.
5. Install the new control board and secure it with the screws.
6. Reconnect all the wire harnesses to the new board and confirm the error stays cleared during a full test cycle.
7. Reassemble the dryer and plug it back in to test.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: EF3 Difficulty: Moderate

Problem: Maximum drying time has been reached, but clothes are still wet.

How to Fix EF3 Error (Step-by-Step)

1. Unplug the dryer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
2. Check the lint filter and clean it thoroughly if it’s clogged.
3. Inspect the dryer vent hose for any kinks or blockages and clear them.
4. Locate the moisture sensor bars inside the dryer drum, usually near the lint filter housing.
5. Clean the moisture sensor bars with a cotton ball and rubbing alcohol to remove any residue.
6. If the issue persists, the moisture sensor may need to be replaced.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: ED Difficulty: Hard

Problem: Faulty main control board.

How to Fix ED Error (Step-by-Step)

1. Unplug the dryer’s power cord from the electrical outlet for safety.
2. Remove the top panel of the dryer by taking out the screws from the back and sliding the panel off.
3. Locate the main control board. It is typically a green circuit board in a plastic housing mounted to the side of the dryer’s frame.
4. To avoid incorrect wiring, take a clear picture of the board and all its connections before you proceed.
5. Disconnect all the wire harnesses attached to the board. Then, remove the mounting screws and lift the faulty control board out of the dryer.
6. Set the new main control board in place and fasten it with the screws. Reconnect all the wire harnesses, referring to your picture to ensure they are in the correct locations.
7. Reattach the top panel, plug the dryer in, and run a test cycle to confirm that the new board has fixed the issue.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: EBF Difficulty: Hard

Problem: Console control problem.

How to Fix EBF Error (Step-by-Step)

1. Begin by unplugging the dryer from the wall to cut off all electrical power.
2. Remove the dryer’s top panel by unscrewing the retaining screws at the rear of the machine.
3. Identify the console control board, which is the circuit board directly behind the control panel buttons and display.
4. Photograph the connections between the console board and the main control board to ensure correct reassembly.
5. Disconnect the wire harnesses and ribbon cables from the console board. Remove the screws or unclip the tabs holding it to the control panel and remove it.
6. Fit the new console control board into place and secure it. Reattach all wiring, double-checking the connections against your photo.
7. Put the top panel back on the dryer and secure it. Restore power and test the dryer’s control functions.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: EBE Difficulty: Hard

Problem: Console control problem.

How to Fix EBE Error (Step-by-Step)

1. Disconnect the dryer from its power source by unplugging the power cord.
2. Remove the top panel to get access to the control area. This usually involves removing a few screws from the back of the dryer.
3. Locate the console control, also known as the user interface board. This is the board that your buttons and display are attached to.
4. Take a picture of the ribbon cables and wire harnesses connected to the console control board.
5. Carefully disconnect the wiring from the old board. Remove any screws or release clips holding it in place and remove it from the console.
6. Install the new console control board, securing it properly. Reconnect the ribbon cables and wire harnesses as they were in your photo.
7. Reassemble the dryer by reattaching the top panel. Plug the dryer in and check if the controls and display are now functioning correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: EAE Difficulty: Hard

Problem: Line safe relay sensing failure.

How to Fix EAE Error (Step-by-Step)

1. Ensure your safety by unplugging the dryer from the power outlet.
2. Access the internal components by removing the screws on the back of the dryer and lifting off the top panel.
3. Locate the main control board. This board contains the relay that is causing the error.
4. Take a clear photo of all the wire connections on the board to use as a reference.
5. Disconnect each wire harness from the control board. Be gentle to avoid damaging the connectors. Remove the screws holding the board and take it out.
6. Place the new control board into the dryer and secure it with the screws. Carefully plug all the wire harnesses back into their correct spots, using your photo as a guide.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: EA5 Difficulty: Hard

Problem: Fatal error of the main control.

How to Fix EA5 Error (Step-by-Step)

1. Turn off the power to the dryer by unplugging it from the wall outlet.
2. Remove the top panel of the dryer by taking out the screws located on the back edge.
3. Identify the main control board inside the dryer. It is usually a green circuit board inside a plastic case.
4. Before touching any wires, take a detailed photograph to remember where each connector goes.
5. Carefully unplug all the wire harnesses connected to the control board. Remove the screws that hold the board in its housing and lift it out.
6. Position the new control board in place and secure it with the mounting screws. Reconnect all the wire harnesses according to your reference photo.
7. Replace the top panel and its screws. Plug the dryer back in and test its operation by starting a new cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes