Author: ApplianceFixGuide Team

Problem: No Water Detected Entering Tub

How to Fix 6-1 Error

1. First, ensure the hot water supply valve for the dishwasher (usually under the sink) is fully open.
2. Check the water inlet hose for any kinks or blockages.
3. If the water supply is good, the water inlet valve on the dishwasher has failed. Shut off the water supply and disconnect power.
4. The valve is typically located at the front-bottom of the dishwasher. Remove the lower access panel.
5. Disconnect the water line, outlet hose, and wire harness. Replace the valve and reconnect everything.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Suds or Air in Water Pump

How to Fix 6-3 Error

1. This error means too many suds have been detected, usually from using the wrong detergent (like hand soap) or too much detergent.
2. Press the ‘Cancel’ button to drain the dishwasher.
3. Open the door and pour 1 cup of vegetable oil into the bottom of the tub. The oil will break down the suds.
4. Run a ‘Rinse Only’ cycle.
5. To prevent this, only use high-quality automatic dishwasher detergent and use the recommended amount.

Browse all Maytag error codes: Maytag Error Codes

Problem: Float Switch Open / Stuck

How to Fix 6-4 Error

1. This error indicates the float switch, which detects the water level, is stuck in the open (up) position.
2. Open the dishwasher and locate the float assembly (a plastic dome or cylinder) in the bottom of the tub.
3. Check for any debris or food particles that may be holding the float up. Clean the area thoroughly.
4. Lift the float up and down to ensure it moves freely.
5. If the float is free but the error persists, the electrical switch underneath it has failed. Disconnect power, access the switch from below the tub, and replace it.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Flow Meter Disconnected / Damaged

How to Fix 6-7 Error

1. Disconnect the dishwasher from power.
2. The flow meter measures how much water is entering the tub and is part of the case break assembly on the side of the dishwasher.
3. You will need to pull the dishwasher out from the cabinet to access the side.
4. Locate the case break assembly (a large, clear plastic labyrinth). Check the wire harness connection to the flow meter.
5. If the connection is good, the entire case break assembly containing the flow meter needs to be replaced. This involves disconnecting multiple hoses.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Heating Element Doesn’t Work

How to Fix 7-1 Error

1. Disconnect the dishwasher from power at the circuit breaker.
2. Access the heating element from the front-bottom of the dishwasher by removing the lower panels.
3. Disconnect the wires from the heating element terminals.
4. Use a multimeter to test the element for continuity. A good element will have a resistance reading (typically 10-30 ohms). An open circuit (infinite ohms) means the element is bad.
5. If the element is bad, remove the nuts holding it in place and replace it with the new one.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Heating Element Won’t Shut Off

How to Fix 7-2 Error

1. DANGER: This is a serious safety issue. Immediately shut off power to the dishwasher at the circuit breaker to prevent overheating.
2. This error means a relay on the main control board is stuck, continuously sending power to the heating element.
3. The main control board must be replaced. It is usually located at the base of the dishwasher.
4. Access the board, carefully transfer all wire connections to the new board, and install it.
5. Reassemble and restore power.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Temperature Sensor Fault

How to Fix 8-4 Error

1. Disconnect the dishwasher from power.
2. In many Maytag models, the temperature sensor (thermistor) is integrated into the main control board and is not a separate, replaceable part.
3. If you receive this error, it means the main control board has a fault and the entire board needs to be replaced.
4. Access the main control board at the base of the unit, transfer the wiring to the new board, and install it.

Browse all Maytag error codes: Maytag Error Codes

Problem: Water Circulation Pump Issue

How to Fix 8-5 Error

1. Disconnect the dishwasher from power.
2. This error points to a failure of the main wash motor / circulation pump.
3. You will need to pull the dishwasher out and lay it on its back to access the motor from underneath.
4. Disconnect the hoses and wire harnesses connected to the motor assembly.
5. Unbolt the old motor and install the new one.
6. Reconnect all hoses and wiring securely before setting the dishwasher upright and reinstalling.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Leak Detection / Flood Protection Active

How to Fix E15 Error

1. Disconnect the dishwasher from power and shut off the water supply. This error indicates water has leaked into the base pan and activated the flood switch.
2. Pull the dishwasher out from under the counter. Tilt it forward at a 45-degree angle to drain the water from the base pan into a towel.
3. You must find and fix the source of the leak. Common culprits are a cracked drain pump, a loose hose connection, or a bad door seal.
4. Inspect the drain pump and float switch for damage. The float switch can be tested for continuity; it should be open when down and closed when lifted. Replace any faulty parts.
5. Once the leak is repaired and the base pan is dry, reassemble and restore power.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Restricted Drain / Drain Check Valve Fault

How to Fix F4E3 Error

1. Disconnect the dishwasher from power.
2. This error indicates a problem with the drain check valve, which is part of the wash motor/circulation pump assembly.
3. You will need to pull the dishwasher out and likely turn it on its back or side to access the wash motor from underneath.
4. Disconnect the hoses and wire harnesses from the wash motor assembly.
5. Unbolt and remove the entire motor assembly. The check valve is an internal component, so the standard repair is to replace the whole wash motor unit.
6. Install the new motor, reconnect all hoses and wiring, and reassemble.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes