Author: ApplianceFixGuide Team

  • How to Fix Whirlpool Washer Error F9E2

    How to Fix Whirlpool Washer Error F9E2

    Problem: Drain pump electrical fault – open circuit or short detected in pump motor

    How to Fix Washer Error

    1. Unplug washer and remove lower front panel.
    2. Locate drain pump assembly mounted at bottom front of tub.
    3. Disconnect pump wiring harness connector.
    4. Measure resistance across pump motor terminals with multimeter (should read 10-20 ohms).
    5. If resistance is infinite (open circuit) or zero (shorted), pump motor has failed.
    6. Verify 120V AC reaches pump connector during drain cycle (use multimeter with washer running).
    7. Inspect wiring harness between pump and control board for damage near vibration points.
    8. Check pump impeller for freedom of movement (remove filter cap and rotate manually).
    9. If electrical tests confirm pump failure, replace drain pump assembly W
    10. After replacement, run diagnostic drain cycle verifying pump operates continuously during drain phase without overheating.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Dishwasher Error F05

    How to Fix Kenmore Dishwasher Error F05

    Problem: Overfill condition detected by float switch

    How to Fix Dishwasher Error

    1. Check float switch assembly for proper movement and continuity.
    2. Inspect drain system for blockages causing backup.
    3. Test overfill protection switch operation.
    4. Verify drain pump is functioning correctly.
    5. Replace control board if sensors test good but error persists.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Whirlpool Washer Error FH

    How to Fix Whirlpool Washer Error FH

    Problem: No water flow detected during fill cycle (older Duet models)

    How to Fix Washer Error

    1. Verify both hot/cold water supply valves are fully open.
    2. Disconnect fill hoses from washer and check household water pressure (>20 PSI required).
    3. Clean inlet valve screens by removing hoses and brushing debris from brass fittings.
    4. Inspect fill hoses for kinks, excessive length (>6 feet), or internal collapse.
    5. Remove top panel and locate flow meter (clear plastic housing with turbine) on inlet valve assembly.
    6. Verify turbine spins freely when water flows (observe during brief fill attempt).
    7. If turbine is stuck, replace water inlet valve assembly W
    8. Check pressure switch hose connection at air dome on tub – must be secure and dry.
    9. If water flows but error persists, replace pressure switch W
    10. After repair, verify washer fills to proper level within 6 minutes on normal cycle.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Washer Error F15

    How to Fix Kenmore Washer Error F15

    Problem: Motor control unit error – communication failure

    How to Fix Washer Error

    1. Turn off power at circuit breaker.
    2. Remove front access panel and motor control board cover.
    3. Inspect motor control board connectors for corrosion or damage.
    4. Check wiring harness between motor control and main control boards.
    5. Test communication signals with multimeter if possible.
    6. Clean all electrical contacts with contact cleaner.
    7. If connections are good but error persists, replace motor control board.
    8. Document all wire connections before disconnecting.
    9. Install new motor control board assembly.
    10. Test motor operation and communication with main control board.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Whirlpool Washer Error Sd

    How to Fix Whirlpool Washer Error Sd

    Problem: Excessive suds detected – suds lock condition preventing proper drainage/spin

    How to Fix Washer Error

    1. Cancel current cycle and select ‘Drain & Spin’ cycle without adding detergent.
    2. Allow washer to complete 2-3 consecutive drain/spin cycles to remove excess suds.
    3. Use only HE (High-Efficiency) detergent going forward – never regular detergent in HE washer.
    4. Measure detergent carefully: 2 tablespoons liquid HE or 1 tablespoon powder HE per load.
    5. Avoid ‘2x concentrated’ or ‘ultra’ detergents unless specifically formulated for HE machines.
    6. Never use fabric softener directly in dispenser – only in designated compartment and never exceeding fill line.
    7. If suds persist after multiple drain cycles, run empty ‘Clean Washer’ cycle with affresh tablet or 1 cup white vinegar.
    8. Inspect dispenser drawer for caked detergent residue – clean thoroughly with warm water.
    9. Verify drain pump filter is clean (debris can trap suds in system).
    10. If suds lock occurs repeatedly with proper detergent usage, check for leaking dispenser actuator allowing continuous detergent flow.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Dishwasher Error F06

    How to Fix Kenmore Dishwasher Error F06

    Problem: Motor control unit (MCU) communication failure

    How to Fix Dishwasher Error

    1. Reset control board by disconnecting power for 15 minutes.
    2. Check all motor harness connections for corrosion or damage.
    3. Test motor windings for proper resistance values.
    4. Inspect MCU board for burned components or bad solder joints.
    5. Replace MCU board if communication cannot be restored.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Whirlpool Washer Error OL

    How to Fix Whirlpool Washer Error OL

    Problem: Overload condition – mechanical load on motor exceeds safe operating limits

    How to Fix Washer Error

    1. Pause cycle and redistribute laundry evenly around tub perimeter.
    2. Remove 2-3 garments if tub is packed tightly (max load should leave 3-4 inches space below tub rim).
    3. Avoid washing single heavy items alone (blankets, rugs) – add towels to balance load.
    4. Check for foreign objects wedged between tubs (coins, tools) causing mechanical binding.
    5. Manually rotate tub assembly with washer unplugged – should spin freely without grinding or excessive resistance.
    6. If tub binds mechanically, remove front panel and inspect for objects trapped between inner/outer tubs.
    7. Verify suspension rods/shocks aren’t broken causing tub to rub against cabinet during spin.
    8. Check drive belt tension – excessive tension increases motor load (should deflect 1/2 inch when pressed midway).
    9. If overload occurs with small loads, suspect failing tub bearing requiring professional repair.
    10. After load adjustment, restart cycle and monitor for smooth acceleration during spin.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Washer Error uL

    How to Fix Whirlpool Washer Error uL

    Problem: Unbalanced load detected during spin cycle – tub vibration exceeds safe limits

    How to Fix Washer Error

    1. Pause cycle when uL appears – washer will attempt automatic rebalancing (may take 5-10 minutes).
    2. If automatic rebalance fails, open lid/door and manually redistribute laundry evenly around tub.
    3. Remove bulky items (comforters, rugs) and wash separately with towels for balance.
    4. Avoid washing single heavy items alone – always add smaller items to distribute weight.
    5. Ensure washer is level front-to-back and side-to-side (use carpenter’s level on top panel).
    6. Adjust leveling legs until all four feet contact floor firmly (rocking indicates instability).
    7. Verify suspension rods/shocks aren’t broken or disconnected (access requires removing cabinet panels).
    8. Check tub glide bearings for excessive wear allowing tub to shift during spin.
    9. If uL occurs repeatedly with balanced loads, suspect failing tub bearing or broken counterweight requiring professional repair.
    10. After redistribution, restart cycle and allow washer to complete automatic rebalance attempts before intervening.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Dryer Error F71

    How to Fix Kenmore Dryer Error F71

    Problem: User interface keypad failure

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Remove control panel faceplate and access cover.
    3. Inspect membrane switch pad for physical damage or debris.
    4. Test each button contact with multimeter for proper continuity.
    5. Clean button contacts with electrical contact cleaner and soft brush.
    6. If membrane switch is damaged, disconnect ribbon cable from control board.
    7. Remove mounting screws and replace entire control panel assembly.
    8. Reconnect ribbon cable and test all button functions.
    9. Clear error code by cycling power and verify operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dishwasher Error F07

    How to Fix Kenmore Dishwasher Error F07

    Problem: Water fill timeout or insufficient water pressure

    How to Fix Dishwasher Error

    1. Verify home water pressure is adequate (minimum 20 PSI).
    2. Check water supply valve is fully open.
    3. Inspect inlet valve screen for mineral deposits or debris.
    4. Test flow meter operation during fill cycle.
    5. Replace water inlet valve if flow is restricted.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes