Author: ApplianceFixGuide Team

  • How to Fix Frigidaire Washer Error E93

    How to Fix Frigidaire Washer Error E93

    Error Code: E93 Difficulty: Moderate

    Problem: Console or Main Board control problem/failure.

    How to Fix E93 Error (Step-by-Step)

    1. Disconnect the washer from its power supply by unplugging it.
    2. Open the control console to access the user interface board. This may require removing screws from the top or back of the console.
    3. Take a photo of the current wire setup for easy reassembly.
    4. Disconnect the wire harnesses attached to the user interface board.
    5. Remove the screws that are holding the board to the console panel.
    6. Position the new user interface board and secure it with the screws.
    7. Reconnect the wire harnesses as they were previously, close the console, and restore power to the washer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E91

    How to Fix Frigidaire Washer Error E91

    Error Code: E91 Difficulty: Hard

    Problem: User interface board or UI/main board communication failure.

    How to Fix E91 Error (Step-by-Step)

    1. Power down the washer completely by unplugging it from the wall outlet.
    2. Access both the main control board (usually at the bottom or back) and the user interface board (in the top console).
    3. Carefully inspect the wiring harness that runs between the two boards.
    4. Look for any signs of pinched, broken, or disconnected wires.
    5. Reseat the connections on both ends of the harness to ensure a firm connection.
    6. If the wiring looks good, the issue is likely one of the boards. Replacing the user interface board is often easier for homeowners.
    7. If replacing the UI board doesn’t solve the issue, the main control board will likely need to be replaced.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • (Varies by model) (User Interface Board)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E83

    How to Fix Frigidaire Washer Error E83

    Error Code: E83 Difficulty: Moderate

    Problem: Console control problem.

    How to Fix E83 Error (Step-by-Step)

    1. Unplug the washer from the electrical outlet to prevent electric shock.
    2. Gain access to the console control by removing the top panel or disassembling the front console area.
    3. Before disconnecting anything, take a clear photo of the wiring connections to the user interface board for reference.
    4. Gently unplug the wire connectors from the board and confirm the error stays cleared during a full test cycle.
    5. Remove the mounting screws or unclip the tabs holding the board in place and remove the old board.
    6. Install the new user interface board, making sure it is securely seated.
    7. Reattach the wire connectors to the correct terminals on the new board and reassemble the console.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E82

    How to Fix Frigidaire Washer Error E82

    Error Code: E82 Difficulty: Moderate

    Problem: Console control problem.

    How to Fix E82 Error (Step-by-Step)

    1. Disconnect the washer from the wall outlet to ensure your safety.
    2. To access the user interface board, you will likely need to remove the top panel or the control console housing.
    3. Take a picture of the wire connections to the board before proceeding.
    4. Carefully disconnect all the wire harnesses and any grounding wires from the old user interface board.
    5. Remove the screws or release the plastic tabs that secure the board to the control panel.
    6. Mount the new user interface board in the same position.
    7. Reconnect all wiring harnesses based on the photo you took, secure the control panel, and plug the washer back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E76

    How to Fix Frigidaire Washer Error E76

    Error Code: E76 Difficulty: Easy

    Problem: NTC temperature for the cold water valve is over the limits.

    How to Fix E76 Error (Step-by-Step)

    1. Check that your cold water supply hose is connected to the ‘Cold’ water inlet on the back of the washer.
    2. Ensure the cold water faucet is turned on completely and confirm the error stays cleared during a full test cycle.
    3. Verify that the water coming from your cold water supply is actually cold. If you have a plumbing issue causing warm water in the cold line, this error can occur.
    4. Straighten any kinks in the cold water hose that could be restricting flow.
    5. Disconnect the cold water hose from the washer and check the small filter screen inside the inlet port for any debris or sediment, and clean it if necessary.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E75

    How to Fix Frigidaire Washer Error E75

    Error Code: E75 Difficulty: Moderate

    Problem: Water temperature sensor circuit failure.

    How to Fix E75 Error (Step-by-Step)

    1. Unplug the washing machine from its power source and confirm the error stays cleared during a full test cycle.
    2. Turn off the water supply and disconnect the hot and cold water hoses.
    3. Locate the water temperature sensor, which is typically found near the water inlet valve or on the heating element at the base of the tub.
    4. Carefully inspect the wiring connected to the sensor for any visible signs of damage, corrosion, or loose connections.
    5. Disconnect the wire harness from the sensor and confirm the error stays cleared during a full test cycle.
    6. Remove the old sensor by unscrewing or unclipping it from its housing.
    7. Install the new sensor, reconnect the wiring harness, and reassemble the washer panels.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E71

    How to Fix Frigidaire Washer Error E71

    Error Code: E71 Difficulty: Moderate

    Problem: Wash NTC (heater) failure.

    How to Fix E71 Error (Step-by-Step)

    1. Disconnect the washer from the electrical outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Drain any remaining water from the machine by placing the drain hose lower than the tub level into a bucket.
    3. Access the heating element, usually located at the bottom of the washtub from the front or rear panel.
    4. The water temperature sensor (NTC) is mounted on or near the heating element.
    5. Carefully disconnect the wiring from the sensor and confirm the error stays cleared during a full test cycle.
    6. Unclip or unscrew the old sensor and gently pull it out. You may need to wiggle it to break the seal.
    7. Insert the new sensor, ensuring a snug fit, reconnect the wiring, and reassemble the access panel.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E70

    How to Fix Frigidaire Washer Error E70

    Error Code: E70 Difficulty: Moderate

    Problem: Cold water is not entering or the control board is not seeing the correct water supply.

    How to Fix E70 Error (Step-by-Step)

    1. Ensure both hot and cold water supply valves are fully open and that the water inlet hoses are not kinked or clogged.
    2. Unplug the washer from the power source and confirm the error stays cleared during a full test cycle.
    3. Turn off the water supply valves and confirm the error stays cleared during a full test cycle.
    4. Access the water inlet valve at the back of the washer where the hoses connect.
    5. Disconnect the hoses and the wire harnesses from the valve.
    6. Remove the screws holding the old valve in place and install the new one.
    7. Reconnect the wire harnesses and water hoses, then turn the water supply back on and plug in the washer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 124294111 (Water Temperature Sensor)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E67

    How to Fix Frigidaire Washer Error E67

    Error Code: E67 Difficulty: Hard

    Problem: Incorrect input voltage on the microprocessor.

    How to Fix E67 Error (Step-by-Step)

    1. Unplug the washer from the electrical outlet to prevent any risk of electric shock.
    2. Turn off the main water supply valves leading to the washer.
    3. Access the main control board, which is typically located inside the top panel or behind the rear access panel.
    4. Carefully disconnect all the wire harnesses attached to the board, taking a photo beforehand can help with reassembly.
    5. Remove the screws or clips holding the old control board in place and gently lift it out.
    6. Install the new main control board, securing it with the screws or clips.
    7. Reconnect all the wire harnesses to the new board, referencing the photo you took earlier to ensure correct placement.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E5F

    How to Fix Frigidaire Washer Error E5F

    Error Code: E5F Difficulty: Hard

    Problem: Communication problem/failure.

    How to Fix E5F Error (Step-by-Step)

    1. Unplug the washing machine for safety and confirm the error stays cleared during a full test cycle.
    2. Remove the top and rear access panels to expose the electronics.
    3. Locate the main control board and the motor control board. A wiring harness connects them.
    4. Visually inspect the entire length of this harness for any breaks, burns, or loose pins in the connectors.
    5. Reseat the connectors firmly on both boards to rule out a loose connection.
    6. If the wiring is undamaged, the fault is likely with one of the boards, most commonly the motor control board. Replace the motor control board following the steps for error E5A.
    7. Reassemble the washer and test its function and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • (Varies by model) (Main Control Board)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes