Author: ApplianceFixGuide Team

  • How to Fix Frigidaire Washer Error E5E

    How to Fix Frigidaire Washer Error E5E

    Error Code: E5E Difficulty: Hard

    Problem: Communication problem.

    How to Fix E5E Error (Step-by-Step)

    1. Disconnect the washer from power and confirm the error stays cleared during a full test cycle.
    2. Remove the washer’s top and back panels to access the control boards.
    3. Identify the main control board (top) and the motor control board (bottom).
    4. Trace the communication cable (a multi-wire harness) that connects the two boards.
    5. Check for a secure connection at both ends. Unplug the connectors, inspect for corrosion on the pins, and plug them back in securely.
    6. If connections are good, the motor control board is the next part to replace. Follow the steps for error E5A to replace it.
    7. After replacement, reattach the panels and test the machine and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • (Varies by model) (Main Control Board)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E5D

    How to Fix Frigidaire Washer Error E5D

    Error Code: E5D Difficulty: Hard

    Problem: Communication problem/failure.

    How to Fix E5D Error (Step-by-Step)

    1. Unplug the washer from the electrical outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the top and rear panels to get full access to the internal wiring and control boards.
    3. Locate the main control board (usually at the top) and the motor control board (at the bottom, near the motor).
    4. Carefully inspect the wiring harness that runs between these two boards. Look for any loose connections, pinched wires, or signs of damage.
    5. Disconnect and then firmly reconnect the harness at both the main board and the motor control board ends.
    6. If the wiring appears intact, the motor control board is the most likely component to have failed. Proceed to replace it following the steps for error E5A.
    7. Reassemble the panels and test the washer and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • (Varies by model) (Main Control Board)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E5C

    How to Fix Frigidaire Washer Error E5C

    Error Code: E5C Difficulty: Hard

    Problem: High temperature on the heat sink or a motor-related issue.

    How to Fix E5C Error (Step-by-Step)

    1. Disconnect the washer from its power source and confirm the error stays cleared during a full test cycle.
    2. Access the internal components by removing the rear panel of the washer.
    3. Locate the motor control board near the drive motor at the base of the unit. Photograph the wire connections for reference.
    4. Disconnect the wire harnesses from the board by releasing their locking clips.
    5. Remove the mounting screws and replace the old board with the new one.
    6. Secure the new board and reconnect the wire harnesses as they were originally.
    7. Reattach the rear panel and plug the washer back in to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E5B

    How to Fix Frigidaire Washer Error E5B

    Error Code: E5B Difficulty: Hard

    Problem: High temperature on the heat sink.

    How to Fix E5B Error (Step-by-Step)

    1. Unplug the washer from the wall outlet to prevent electrical shock.
    2. Remove the screws from the rear access panel and set the panel aside.
    3. The motor control board is located near the bottom of the washer, close to the drive motor. Take a picture of the wiring.
    4. Carefully unplug each wire connector from the board, pressing the release tabs.
    5. Unscrew the old motor control board and remove it from the machine.
    6. Mount the new board in the same location and secure it with the screws.
    7. Reconnect all wires correctly, replace the rear panel, and restore power to the washer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E5A

    How to Fix Frigidaire Washer Error E5A

    Error Code: E5A Difficulty: Hard

    Problem: High temperature on the heat sink.

    How to Fix E5A Error (Step-by-Step)

    1. Disconnect the washer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the rear access panel of the washer by taking out the screws holding it in place.
    3. Locate the motor control board, which is a circuit board situated near the main drive motor at the bottom of the machine.
    4. Take a clear photo of the wire connections before proceeding.
    5. Disconnect all wire harnesses from the board. They are secured with locking tabs.
    6. Remove the screws mounting the board to the washer’s frame and install the new board.
    7. Reconnect the wires using your photo as a guide, then replace the rear panel.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E55

    How to Fix Frigidaire Washer Error E55

    Error Code: E55 Difficulty: Hard

    Problem: Motor overheating or an issue with the water temperature sensor.

    How to Fix E55 Error (Step-by-Step)

    1. Unplug the washer and turn off the water supply. Disconnect the hoses.
    2. Carefully lay the washer on its back on a soft surface like a blanket to access the bottom.
    3. Locate the drive motor. First, remove the drive belt by walking it off the large pulley.
    4. Disconnect the wire harness connected to the motor and confirm the error stays cleared during a full test cycle.
    5. Remove the bolts that mount the motor to the washer’s base.
    6. Install the new motor, secure it with the mounting bolts, and reconnect the wire harness.
    7. Reinstall the drive belt, carefully return the washer to an upright position, and reconnect all hoses and power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E48

    How to Fix Frigidaire Washer Error E48

    Error Code: E48 Difficulty: Moderate

    Problem: The control board thinks the door PTC circuit is closed.

    How to Fix E48 Error (Step-by-Step)

    1. Unplug the washer from the wall for safety and confirm the error stays cleared during a full test cycle.
    2. Open the door and locate the metal or plastic clamp ring on the outside of the rubber door seal. Use pliers to expand and remove this clamp.
    3. Fold the rubber door seal back into the drum to access the door lock assembly.
    4. Unscrew the two screws holding the door lock assembly to the front panel of the washer.
    5. Disconnect the wiring harness from the back of the old lock assembly.
    6. Connect the new lock assembly to the wiring harness and secure it to the front panel with the screws.
    7. Re-secure the rubber door seal with the clamp, ensuring it is evenly seated.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E47

    How to Fix Frigidaire Washer Error E47

    Error Code: E47 Difficulty: Moderate

    Problem: The control board thinks the door PTC circuit is open in spin.

    How to Fix E47 Error (Step-by-Step)

    1. Disconnect the washer from the electrical outlet and confirm the error stays cleared during a full test cycle.
    2. Open the washer door and locate the flexible rubber boot. Find the spring clamp that holds it to the front panel.
    3. Carefully pry off the spring clamp and peel the boot away from the door opening, exposing the door lock assembly.
    4. Remove the screws that attach the door lock to the washer’s chassis.
    5. Pull the lock assembly out and disconnect the electrical plug attached to it.
    6. Attach the electrical plug to the new door lock assembly.
    7. Screw the new assembly into place, then carefully work the rubber boot and spring clamp back into their original positions.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E46

    How to Fix Frigidaire Washer Error E46

    Error Code: E46 Difficulty: Hard

    Problem: Control board problem.

    How to Fix E46 Error (Step-by-Step)

    1. Unplug the washing machine to ensure safety and confirm the error stays cleared during a full test cycle.
    2. Remove the top panel by taking out the screws located on the back of the washer.
    3. Find the main control board inside a plastic housing. Take a photo of the wire layout for later reference.
    4. Disconnect the multiple wire harnesses attached to the board by releasing their locking tabs.
    5. Unfasten the screws or clips holding the control board and its housing.
    6. Replace the old board with the new one, making sure it snaps securely into place.
    7. Use your photo to reconnect all wires, then screw the top panel back on and plug in the machine.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes

  • How to Fix Frigidaire Washer Error E45

    How to Fix Frigidaire Washer Error E45

    Error Code: E45 Difficulty: Hard

    Problem: Control board problem or problem with the door lock circuit.

    How to Fix E45 Error (Step-by-Step)

    1. Ensure the washer is completely disconnected from power and confirm the error stays cleared during a full test cycle.
    2. Remove the top cover of the washer to gain access to the internal components.
    3. Locate the main control board, easily identified by the large number of wires connected to it.
    4. Take a picture of the board and its connections to ensure you can reconnect everything correctly.
    5. Disconnect all the wire harnesses from the board. These have small clips that must be depressed to release.
    6. Remove the board from its mountings, which may be screws or plastic clips.
    7. Install the new board, reconnect the wires precisely, and then secure the top panel before restoring power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Frigidaire error codes: Frigidaire Error Codes